Tiger Products Co., Ltd TWR-120, TWR-180 manual Hubs and Spindles

Page 77

MAINTENANCE

Hubs and Spindles

Greasing and Installation

It is recommended that hubs are dismantled, cleaned and repackede every year. Use the diagram and following instructions for maintaining the wheel hubs. Whenever a worn or damaged seal is replaced the bearing assembly should be cleaned and repacked with a good grade of wheel grease.

Always wear protective gloves when handling grease.

CAUTION!

AXLE

SEAL

ROLLER BEARING

RACE

HUB

RACE

ROLLER BEARING

COTTER PIN

WASHER

CASTLE NUT

DUST CAP

1.Using a grease packer, pack both roller bearings with a good grade of wheel grease. The bearings should be thoroughly coated with grease. Spread grease on the outside of the bearing with your gloved finger. Ensure that no dirt or filings contact the grease or the bearings.

2.Pack the inside of the hub with grease. Grease needs to cover complete surface area inside hub but does not need to fill cavity.

3.Smear grease on both races.

4.Install the large bearing into the back of the hub and rotate the bearing several times.

5.Install the dust/grease seal using the right size seal driver. Spread a film of grease on the dust seal rubber and on the axle where the seal fits.

6.Position the hub on the axle and firmly push into place then pull hub towards you about 1". Slowly rotate hub while gently pushing the hub back onto the axle.

7.Check dust seal to ensure seal rubber is positioned correctly.

8.Install the small or outer bearing.

TWR-180/TWR-120 12/04

Maintenance Section 5-5

 

 

© 2004 Alamo Group Inc.

 

MAINTENANCE

Page 76 Page 78
Image 77
Page 76 Page 78
Contents TWR-180 TWR-120 To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety SafetySafety SG-10 Abide by the following rules Possible serious injury or death Keep Away from Rotating Elements to prevent entanglementImplement, an operator on prescription or over-the-counter Straighten or Weld on Blades Since this will Likely Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Parts Information Or even death. STI-4Safety QTY Description TWR-180 / TWR-120 12/04 Safety Section See Inside Fornt Cover Serial Plate Safety On 10 Units Only TWR-180 / TWR-120 12/04 Safety Section TWR-180 / TWR-120 12/04 Safety Section Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionAssembly Section Connection to Tractor AssemblyGeneral Wing Lift Spacer Plates Center Wheel Standard Spacer Plates Adjustable SkidsDriveline Shield Chains Laminated TiresCenter Section Wheel Standards Transport Light Kit Rephasing Groove Hydraulic Phasing CylindersSpool Valve Kit Operation Section Operation Tiger Rotary Mower Operation Instructions OperationMedias de seguridad. SG-3 OperationMower Standard Equipment And Specifications Operator’s alertness and coordination and therefore affect Operator RequirementsTractor and Implement. Drugs and alcohol will affect an Tractor Requirements Tractor Safety DevicesTractor Requirements and Capabilities Rops and Seat BeltFront End Weight Tractor HorsepowerDrawbar Tractor HydraulicsTire Spacing Minimum Width Power Take Off PTOTire Spacing Boarding the Tractor Getting on and OFF the TractorDismounting the Tractor Falling off can result in serious injury or death . SG-10Starting the Tractor Safety Tow Chain Operation Connecting the Mower to the TractorHydraulic Cylinder Priming Setting the MowerHydraulic Line Support Setting Deck Pitch Setting Cutting HeightDriveline Length Check Driveline AttachmentDriveline in maximum compressed position Bottoming Out Check ProcedureEngagement Check Procedure Constant Velocity CV Driveline CV Driveline Maximum Angle Check ProcedureEntanglement, injury or death. SRM-3 PRE-OPERATION Inspection and ServiceMower Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceOperation Operation Traffic around you and watch out for the other guy. SG-19 Driving the Tractor and MowerStarting the Tractor Brake and Differential Lock SettingTransport Position Operating the Mower WingsDriving the Tractor and Mower Crossing Ditches and Steep Inclines Resuming mowing. SGM-5 Operating the Tractor and MowerForeign Debris Hazards Stop Mowing if Passersby are Within 100 Yards Unless Bystander/Passersby PrecautionsFrom the blades. SRM-7 Engaging the Power Take Off PTOPTO RPM and Ground Speed Operating the Mower Mowing . S G M Operation Disconnecting the Mower from the Tractor Mower Storage Tires and Wheels Transporting the Tractor and MowerOperation Transporting on Public RoadwaysOperation Hauling the Tractor and Mower Trouble Shooting Guide Maintenance Section Slip Clutches MaintenanceDisassembly Maintenance Hydraulics Nuts and BoltsHubs and Spindles Tires Blade Removal Blade InstallationBlade Servicing Blade Carrier Removal Blade Carrier InstallationMaintenance Grease Schedule Storage Cutter FrameTiger Warranty InformationONE Last Word TWR-180-/TWR-120 12/04 C314TG010C

TWR-120, TWR-180 specifications

Tiger Products Co., Ltd has established itself as a leader in the manufacturing of advanced welding and cutting equipment. Among its innovative offerings are the TWR-180 and TWR-120 models, which have quickly gained attention for their superior technology, robust features, and reliable performance.

The TWR-180 is designed for high-capacity operations, featuring an impressive welding output that makes it suitable for a variety of applications in industries such as automotive, construction, and heavy machinery. One of the standout features of the TWR-180 is its dual pulse technology, which allows for precise control over welding depth and heat input. This technology not only enhances the quality of welds but also minimizes material distortion, making it ideal for intricate designs and complex assemblies.

In addition to its advanced welding capabilities, the TWR-180 includes digital control systems that provide operators with real-time feedback on welding parameters. This user-friendly interface is complemented by programmable memory settings that allow users to save specific welding configurations, thereby enhancing productivity. The TWR-180 is also equipped with a high-efficiency cooling system that prevents overheating during extended use, ensuring that the equipment remains operational without interruptions.

On the other hand, the TWR-120 is specifically tailored for smaller-scale projects while maintaining professional-grade performance. The compact design of the TWR-120 makes it easy to transport and set up, which is vital for on-site applications. It features a simplified control panel that allows for quick adjustments, making it accessible for operators with varying levels of expertise.

Despite its smaller size, the TWR-120 does not compromise on power; it is equipped with innovative inverter technology that maximizes energy efficiency while providing stable output across various welding tasks. This model is particularly appealing to small businesses and workshops looking for a reliable yet versatile welding solution.

Both the TWR-180 and TWR-120 utilize advanced arc stabilization technologies that enhance the quality of the weld, reduce spatter, and improve overall efficiency. These characteristics, combined with exceptional durability and low maintenance requirements, highlight Tiger Products Co., Ltd's commitment to delivering top-tier equipment that meets the needs of diverse industries.

In summary, the TWR-180 and TWR-120 reflect Tiger Products Co., Ltd’s dedication to innovation, quality, and user-centric design. Whether for high-capacity operations or smaller-scale tasks, these models provide exceptional performance and reliability that set them apart in the competitive welding equipment market.
Top Page Image Contents