Tiger Products Co., Ltd TWR-120, TWR-180 manual Setting Cutting Height, Setting Deck Pitch

Page 47

OPERATION

6.1 SETTING CUTTING HEIGHT

The cut height for the center section is set by extending or shortening the depth collar located on the center lift cylinder. Cutting height for the wing cylinders will be automatically controlled by the hydraulic phasing system. Depth stops are also provided on the wing cylinders as back up for fine adjustments.

IMPORTANT: If depth control stops are not set at the same height as the center cylinder, internal damage may occur to the phasing cylinders.

The cutter should always be operated in the highest position that will produce the desired cutting results. Operating at increased heights will minimize the chances of blades contacting the ground and discharging debris.

Hydraulic Cylinder Depth Collar Adjustment

6.2 Setting Deck Pitch

To facilitate safe and efficient operation, the mower should be operated with the deck approximately 3/4”

LOWER IN THE FRONT THAN THE REAR.

Operating the mower at this pitch will allow the mower to cut the grass only once and requires less work from the tractor. In addition, a more even distribution of the clippings from the rear of the mower will be achieved with this deck pitch.

OPERATION

Adjust the lift rods linking the tongue to the rear axle until the front of the mower is at least 3/4” lower in the front that than the rear. To lower the front, lengthen the lift rods and to raise the front shorten the rods. IMPORTANT: Adjust the lift rods the same amount and maintain equal tension in the rods. Improper adjustment may cause rods to snap or bend. Retighten the jamnuts after the deck pitch has been set.

Leveling Rod Adjustments

Lift Rod

Adjustment

TWR-180 / TWR-120 12/04

Operation Section 4-13

© 2004 Alamo Group Inc.

Page 46 Page 48
Image 47
Page 46 Page 48
Contents TWR-180 TWR-120 To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety SafetySafety SG-10 Abide by the following rules Possible serious injury or death Keep Away from Rotating Elements to prevent entanglementImplement, an operator on prescription or over-the-counter Straighten or Weld on Blades Since this will Likely Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Parts Information Or even death. STI-4Safety QTY Description TWR-180 / TWR-120 12/04 Safety Section See Inside Fornt Cover Serial Plate Safety On 10 Units Only TWR-180 / TWR-120 12/04 Safety Section TWR-180 / TWR-120 12/04 Safety Section Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionAssembly Section Connection to Tractor AssemblyGeneral Wing Lift Spacer Plates Laminated Tires Adjustable SkidsCenter Wheel Standard Spacer Plates Driveline Shield ChainsCenter Section Wheel Standards Transport Light Kit Rephasing Groove Hydraulic Phasing CylindersSpool Valve Kit Operation Section Operation Tiger Rotary Mower Operation Instructions OperationMedias de seguridad. SG-3 OperationMower Standard Equipment And Specifications Operator’s alertness and coordination and therefore affect Operator RequirementsTractor and Implement. Drugs and alcohol will affect an Rops and Seat Belt Tractor Safety DevicesTractor Requirements Tractor Requirements and CapabilitiesTractor Hydraulics Tractor HorsepowerFront End Weight DrawbarTire Spacing Minimum Width Power Take Off PTOTire Spacing Falling off can result in serious injury or death . SG-10 Getting on and OFF the TractorBoarding the Tractor Dismounting the TractorStarting the Tractor Safety Tow Chain Operation Connecting the Mower to the TractorHydraulic Cylinder Priming Setting the MowerHydraulic Line Support Setting Deck Pitch Setting Cutting HeightDriveline Length Check Driveline AttachmentDriveline in maximum compressed position Bottoming Out Check ProcedureEngagement Check Procedure Constant Velocity CV Driveline CV Driveline Maximum Angle Check ProcedureEntanglement, injury or death. SRM-3 PRE-OPERATION Inspection and ServiceMower Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceOperation Operation Traffic around you and watch out for the other guy. SG-19 Driving the Tractor and MowerStarting the Tractor Brake and Differential Lock SettingTransport Position Operating the Mower WingsDriving the Tractor and Mower Crossing Ditches and Steep Inclines Resuming mowing. SGM-5 Operating the Tractor and MowerForeign Debris Hazards Stop Mowing if Passersby are Within 100 Yards Unless Bystander/Passersby PrecautionsFrom the blades. SRM-7 Engaging the Power Take Off PTOPTO RPM and Ground Speed Operating the Mower Mowing . S G M Operation Disconnecting the Mower from the Tractor Mower Storage Tires and Wheels Transporting the Tractor and MowerOperation Transporting on Public RoadwaysOperation Hauling the Tractor and Mower Trouble Shooting Guide Maintenance Section Slip Clutches MaintenanceDisassembly Maintenance Hydraulics Nuts and BoltsHubs and Spindles Tires Blade Removal Blade InstallationBlade Servicing Blade Carrier Removal Blade Carrier InstallationMaintenance Grease Schedule Storage Cutter FrameTiger Warranty InformationONE Last Word TWR-180-/TWR-120 12/04 C314TG010C

TWR-120, TWR-180 specifications

Tiger Products Co., Ltd has established itself as a leader in the manufacturing of advanced welding and cutting equipment. Among its innovative offerings are the TWR-180 and TWR-120 models, which have quickly gained attention for their superior technology, robust features, and reliable performance.

The TWR-180 is designed for high-capacity operations, featuring an impressive welding output that makes it suitable for a variety of applications in industries such as automotive, construction, and heavy machinery. One of the standout features of the TWR-180 is its dual pulse technology, which allows for precise control over welding depth and heat input. This technology not only enhances the quality of welds but also minimizes material distortion, making it ideal for intricate designs and complex assemblies.

In addition to its advanced welding capabilities, the TWR-180 includes digital control systems that provide operators with real-time feedback on welding parameters. This user-friendly interface is complemented by programmable memory settings that allow users to save specific welding configurations, thereby enhancing productivity. The TWR-180 is also equipped with a high-efficiency cooling system that prevents overheating during extended use, ensuring that the equipment remains operational without interruptions.

On the other hand, the TWR-120 is specifically tailored for smaller-scale projects while maintaining professional-grade performance. The compact design of the TWR-120 makes it easy to transport and set up, which is vital for on-site applications. It features a simplified control panel that allows for quick adjustments, making it accessible for operators with varying levels of expertise.

Despite its smaller size, the TWR-120 does not compromise on power; it is equipped with innovative inverter technology that maximizes energy efficiency while providing stable output across various welding tasks. This model is particularly appealing to small businesses and workshops looking for a reliable yet versatile welding solution.

Both the TWR-180 and TWR-120 utilize advanced arc stabilization technologies that enhance the quality of the weld, reduce spatter, and improve overall efficiency. These characteristics, combined with exceptional durability and low maintenance requirements, highlight Tiger Products Co., Ltd's commitment to delivering top-tier equipment that meets the needs of diverse industries.

In summary, the TWR-180 and TWR-120 reflect Tiger Products Co., Ltd’s dedication to innovation, quality, and user-centric design. Whether for high-capacity operations or smaller-scale tasks, these models provide exceptional performance and reliability that set them apart in the competitive welding equipment market.
Top Page Image Contents