Tiger Products Co., Ltd TWR-180 Tractor Requirements and Capabilities, Rops and Seat Belt

Page 40

OPERATION

OPERATION

2. TRACTOR REQUIREMENTS

The tractor used to operate the mower must have the power capacity to lift, pull, and operate the Power Take Off (PTO) at the mower’s rated speed while traveling at a ground speed between 2 and 5 MPH. Operating the mower with a tractor that does not meet the following requirements may cause tractor or mower damage and be a potential danger to the operator and passersby.

Tractor Requirements and Capabilities

¾ASAE approved Roll-Over Protective Structure (ROPS) or ROPS cab and seat belt.

¾Tractor Safety Devices

Slow Moving Vehicle (SMV) emblem, lighting,

 

 

PTO master shield

¾Tractor Horsepower -Minimum

TWR-180 65 HP; TWR-120 50 HP

 

-Recommended

TWR-180 85 HP; TWR-120 75 HP

¾Drawbar

Set length according to operating speed and driveline type, rated

 

 

to carry weight of the mower, safety chain attachment point

¾Hydraulics

-Minimum

3 single acting circuits @ 1750 psi

 

-Phasing

1 double acting circuit and 2 single acting circuits @ 1750 psi

¾Front End Weights..…….............…........... As needed to maintain 20% weight on front axle

¾Power Take Off

Operating speed and shaft size depends on operating speed

 

 

and driveline type of the mower.

¾Tire Spacing

Set tires minimum width of 60” inside to inside of tires.

2.1 ROPS and Seat Belt

A Roll-Over-Protective-Structure (ROPS) and seat belt are essential to protect the operator from falling off the tractor, especially during a roll over where the driver could be crushed and killed. The ROPS and seat belt must be used in conjunction with one another. Only operate the tractor with the ROPS in the raised position and seat belt fastened. Tractor models not equipped with a ROPS and seat belt should have these life saving features installed by an authorized tractor dealer.

WARNING! Operate this Equipment only with a Tractor equipped with an approved roll-over- protective system (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the Tractor--particularly during a turnover when the

operator could be pinned under the ROPS. (SG-7)

2.2 Tractor Safety Devices

If transporting or operating the tractor and mower near a public roadway, the tractor must be equipped with proper warning lighting and a Slow Moving Vehicle (SMV) emblem which are clearly visible from the rear of the unit. Lights and a SMV emblem must be equipped directly on implements if the visibility of the tractor warning signals are obscured.

Maintain all manufacturer equipped safety shields and guards. Always replace shields and guards that were removed for access to connect, service, or repair the tractor or mower. Never operate the tractor PTO with the PTO master shield missing or in the raised position.

TWR-180 / TWR-120 12/04

Operation Section 4-6

© 2004 Alamo Group Inc.

Page 39 Page 41
Image 40
Page 39 Page 41
Contents TWR-180 TWR-120 To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety SafetySafety SG-10 Abide by the following rules Keep Away from Rotating Elements to prevent entanglement Possible serious injury or deathImplement, an operator on prescription or over-the-counter Straighten or Weld on Blades Since this will Likely Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Or even death. STI-4 Parts InformationSafety QTY Description TWR-180 / TWR-120 12/04 Safety Section See Inside Fornt Cover Serial Plate Safety On 10 Units Only TWR-180 / TWR-120 12/04 Safety Section TWR-180 / TWR-120 12/04 Safety Section Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionAssembly Section General AssemblyConnection to Tractor Wing Lift Spacer Plates Adjustable Skids Center Wheel Standard Spacer PlatesDriveline Shield Chains Laminated TiresCenter Section Wheel Standards Transport Light Kit Hydraulic Phasing Cylinders Rephasing GrooveSpool Valve Kit Operation Section Operation Operation Tiger Rotary Mower Operation InstructionsOperation Medias de seguridad. SG-3Mower Standard Equipment And Specifications Tractor and Implement. Drugs and alcohol will affect an Operator RequirementsOperator’s alertness and coordination and therefore affect Tractor Safety Devices Tractor RequirementsTractor Requirements and Capabilities Rops and Seat BeltTractor Horsepower Front End WeightDrawbar Tractor HydraulicsTire Spacing Power Take Off PTOTire Spacing Minimum Width Getting on and OFF the Tractor Boarding the TractorDismounting the Tractor Falling off can result in serious injury or death . SG-10Starting the Tractor Operation Connecting the Mower to the Tractor Safety Tow ChainHydraulic Line Support Setting the MowerHydraulic Cylinder Priming Setting Cutting Height Setting Deck PitchDriveline Attachment Driveline Length CheckEngagement Check Procedure Bottoming Out Check ProcedureDriveline in maximum compressed position CV Driveline Maximum Angle Check Procedure Constant Velocity CV DrivelinePRE-OPERATION Inspection and Service Entanglement, injury or death. SRM-3Tractor Pre-Operation Inspection/Service Mower Pre-Operation Inspection/ServiceOperation Operation Driving the Tractor and Mower Traffic around you and watch out for the other guy. SG-19Brake and Differential Lock Setting Starting the TractorOperating the Mower Wings Transport PositionDriving the Tractor and Mower Crossing Ditches and Steep Inclines Foreign Debris Hazards Operating the Tractor and MowerResuming mowing. SGM-5 Bystander/Passersby Precautions Stop Mowing if Passersby are Within 100 Yards UnlessPTO RPM and Ground Speed Engaging the Power Take Off PTOFrom the blades. SRM-7 Operating the Mower Mowing . S G M Operation Disconnecting the Mower from the Tractor Mower Storage Transporting the Tractor and Mower Tires and WheelsTransporting on Public Roadways OperationOperation Hauling the Tractor and Mower Trouble Shooting Guide Maintenance Section Disassembly MaintenanceSlip Clutches Maintenance Nuts and Bolts HydraulicsHubs and Spindles Tires Blade Servicing Blade InstallationBlade Removal Blade Carrier Installation Blade Carrier RemovalMaintenance Grease Schedule Cutter Frame StorageWarranty Information TigerONE Last Word TWR-180-/TWR-120 12/04 C314TG010C

TWR-120, TWR-180 specifications

Tiger Products Co., Ltd has established itself as a leader in the manufacturing of advanced welding and cutting equipment. Among its innovative offerings are the TWR-180 and TWR-120 models, which have quickly gained attention for their superior technology, robust features, and reliable performance.

The TWR-180 is designed for high-capacity operations, featuring an impressive welding output that makes it suitable for a variety of applications in industries such as automotive, construction, and heavy machinery. One of the standout features of the TWR-180 is its dual pulse technology, which allows for precise control over welding depth and heat input. This technology not only enhances the quality of welds but also minimizes material distortion, making it ideal for intricate designs and complex assemblies.

In addition to its advanced welding capabilities, the TWR-180 includes digital control systems that provide operators with real-time feedback on welding parameters. This user-friendly interface is complemented by programmable memory settings that allow users to save specific welding configurations, thereby enhancing productivity. The TWR-180 is also equipped with a high-efficiency cooling system that prevents overheating during extended use, ensuring that the equipment remains operational without interruptions.

On the other hand, the TWR-120 is specifically tailored for smaller-scale projects while maintaining professional-grade performance. The compact design of the TWR-120 makes it easy to transport and set up, which is vital for on-site applications. It features a simplified control panel that allows for quick adjustments, making it accessible for operators with varying levels of expertise.

Despite its smaller size, the TWR-120 does not compromise on power; it is equipped with innovative inverter technology that maximizes energy efficiency while providing stable output across various welding tasks. This model is particularly appealing to small businesses and workshops looking for a reliable yet versatile welding solution.

Both the TWR-180 and TWR-120 utilize advanced arc stabilization technologies that enhance the quality of the weld, reduce spatter, and improve overall efficiency. These characteristics, combined with exceptional durability and low maintenance requirements, highlight Tiger Products Co., Ltd's commitment to delivering top-tier equipment that meets the needs of diverse industries.

In summary, the TWR-180 and TWR-120 reflect Tiger Products Co., Ltd’s dedication to innovation, quality, and user-centric design. Whether for high-capacity operations or smaller-scale tasks, these models provide exceptional performance and reliability that set them apart in the competitive welding equipment market.
Top Page Image Contents