Tiger Products Co., Ltd TWR-180 manual Starting the Tractor, Brake and Differential Lock Setting

Page 56

OPERATION

OPERATION

DANGER!

 

This Implement is wider than the Tractor. Be careful when operating or transporting

 

 

this equipment to prevent the Implement from running into or striking sign posts, guard

 

rails, concrete abutments or other solid objects. Such an impact could cause the

 

Implement and Tractor to pivot violently resulting in loss of steering control, serious

 

injury, or even death. Never allow the Implement to contact obstacles. (S3PT-12)

9.1 Starting the Tractor

The procedure to start the tractor is model specific. Refer to the tractor operator’s manual for starting procedures for your particular tractor. Consult an authorized dealer if the starting procedure is unclear. Ensure the 3-point control lever is in the lowered position and the PTO is disengaged before starting the tractor.

9.2 Brake and Differential Lock Setting

Make sure the tractor brakes are in good operating condition. Tractor brakes can be set to operate independently allowing single rear wheel braking action or locked together to provide simultaneous rear wheel braking. FOR MOST DRIVING AND MOWING CONDITIONS, THE BRAKE PEDALS SHOULD BE LOCKED TOGETHER TO PROVIDE THE MOST EFFECTIVE BRAKING ACTION.

WARNING! Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes. When operating down a hill or on wet or rain slick roads, the braking distance increases; use extreme care and reduce your speed in these conditions. When operating in traffic, always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy.

Always disengage the tractor differential lock when turning. When engaged the differential lock will prevent or limit the tractor from turning. During normal mowing conditions, locking the differential provides no benefit and should not be used.

TWR-180 / TWR-120 12/04

Operation Section 4-22

© 2004 Alamo Group Inc.

Page 55 Page 57
Image 56
Page 55 Page 57
Contents TWR-180 TWR-120 To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety SafetySafety SG-10 Abide by the following rules Keep Away from Rotating Elements to prevent entanglement Possible serious injury or deathImplement, an operator on prescription or over-the-counter Straighten or Weld on Blades Since this will Likely Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Or even death. STI-4 Parts InformationSafety QTY Description TWR-180 / TWR-120 12/04 Safety Section See Inside Fornt Cover Serial Plate Safety On 10 Units Only TWR-180 / TWR-120 12/04 Safety Section TWR-180 / TWR-120 12/04 Safety Section Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionAssembly Section Connection to Tractor AssemblyGeneral Wing Lift Spacer Plates Adjustable Skids Center Wheel Standard Spacer PlatesDriveline Shield Chains Laminated TiresCenter Section Wheel Standards Transport Light Kit Hydraulic Phasing Cylinders Rephasing GrooveSpool Valve Kit Operation Section Operation Operation Tiger Rotary Mower Operation InstructionsOperation Medias de seguridad. SG-3Mower Standard Equipment And Specifications Operator’s alertness and coordination and therefore affect Operator RequirementsTractor and Implement. Drugs and alcohol will affect an Tractor Safety Devices Tractor RequirementsTractor Requirements and Capabilities Rops and Seat BeltTractor Horsepower Front End WeightDrawbar Tractor HydraulicsTire Spacing Minimum Width Power Take Off PTOTire Spacing Getting on and OFF the Tractor Boarding the TractorDismounting the Tractor Falling off can result in serious injury or death . SG-10Starting the Tractor Operation Connecting the Mower to the Tractor Safety Tow ChainHydraulic Cylinder Priming Setting the MowerHydraulic Line Support Setting Cutting Height Setting Deck PitchDriveline Attachment Driveline Length CheckDriveline in maximum compressed position Bottoming Out Check ProcedureEngagement Check Procedure CV Driveline Maximum Angle Check Procedure Constant Velocity CV DrivelinePRE-OPERATION Inspection and Service Entanglement, injury or death. SRM-3Tractor Pre-Operation Inspection/Service Mower Pre-Operation Inspection/ServiceOperation Operation Driving the Tractor and Mower Traffic around you and watch out for the other guy. SG-19Brake and Differential Lock Setting Starting the TractorOperating the Mower Wings Transport PositionDriving the Tractor and Mower Crossing Ditches and Steep Inclines Resuming mowing. SGM-5 Operating the Tractor and MowerForeign Debris Hazards Bystander/Passersby Precautions Stop Mowing if Passersby are Within 100 Yards UnlessFrom the blades. SRM-7 Engaging the Power Take Off PTOPTO RPM and Ground Speed Operating the Mower Mowing . S G M Operation Disconnecting the Mower from the Tractor Mower Storage Transporting the Tractor and Mower Tires and WheelsTransporting on Public Roadways OperationOperation Hauling the Tractor and Mower Trouble Shooting Guide Maintenance Section Slip Clutches MaintenanceDisassembly Maintenance Nuts and Bolts HydraulicsHubs and Spindles Tires Blade Removal Blade InstallationBlade Servicing Blade Carrier Installation Blade Carrier RemovalMaintenance Grease Schedule Cutter Frame StorageWarranty Information TigerONE Last Word TWR-180-/TWR-120 12/04 C314TG010C

TWR-120, TWR-180 specifications

Tiger Products Co., Ltd has established itself as a leader in the manufacturing of advanced welding and cutting equipment. Among its innovative offerings are the TWR-180 and TWR-120 models, which have quickly gained attention for their superior technology, robust features, and reliable performance.

The TWR-180 is designed for high-capacity operations, featuring an impressive welding output that makes it suitable for a variety of applications in industries such as automotive, construction, and heavy machinery. One of the standout features of the TWR-180 is its dual pulse technology, which allows for precise control over welding depth and heat input. This technology not only enhances the quality of welds but also minimizes material distortion, making it ideal for intricate designs and complex assemblies.

In addition to its advanced welding capabilities, the TWR-180 includes digital control systems that provide operators with real-time feedback on welding parameters. This user-friendly interface is complemented by programmable memory settings that allow users to save specific welding configurations, thereby enhancing productivity. The TWR-180 is also equipped with a high-efficiency cooling system that prevents overheating during extended use, ensuring that the equipment remains operational without interruptions.

On the other hand, the TWR-120 is specifically tailored for smaller-scale projects while maintaining professional-grade performance. The compact design of the TWR-120 makes it easy to transport and set up, which is vital for on-site applications. It features a simplified control panel that allows for quick adjustments, making it accessible for operators with varying levels of expertise.

Despite its smaller size, the TWR-120 does not compromise on power; it is equipped with innovative inverter technology that maximizes energy efficiency while providing stable output across various welding tasks. This model is particularly appealing to small businesses and workshops looking for a reliable yet versatile welding solution.

Both the TWR-180 and TWR-120 utilize advanced arc stabilization technologies that enhance the quality of the weld, reduce spatter, and improve overall efficiency. These characteristics, combined with exceptional durability and low maintenance requirements, highlight Tiger Products Co., Ltd's commitment to delivering top-tier equipment that meets the needs of diverse industries.

In summary, the TWR-180 and TWR-120 reflect Tiger Products Co., Ltd’s dedication to innovation, quality, and user-centric design. Whether for high-capacity operations or smaller-scale tasks, these models provide exceptional performance and reliability that set them apart in the competitive welding equipment market.
Top Page Image Contents