Tiger FLX10, FLX15 manual Stop Mowing if Passersby are Within 100 Yards Unless

Page 14
(STI-2)
(STI-1)

SAFETY

SAFETY

DANGER!

DANGER!

WARNING!

DANGER!

Always disconnect the main PTO Driveline from the Tractor before performing service on the Mower. Never work on the Mower with the tractor PTO driveline connected and running. Blades or Drivelines could turn without warning and cause immediate entanglement, injury or death.

(SRM-3)

Do not turn so sharp or lift mower so high to produce a severe "knocking" of the Driveline which will cause accelerated wear and breakage of drive train components and could result inpossible injury from the separated Driveline sections. (SRM-4)

Do not let the Blades turn when the Mower Deck is raised for any reason, including clearance or for turning. Raising the Mower deck exposes the Cutting Blades which creates a potentially serious hazard and could cause serious injury or even death from objects thrown from the Blades. (SRM-7)

Rotary Mowers are capable under adverse conditions of throwing objects for great distances (100 yards or more) and causing serious injury or death. Follow

safetymessagescarefully

STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESS:

-Front and Rear Deflectors, Chain Guards, or Bands are installed and in good, workable condition;

-Mower sections or Wings are running close to and parallel to the ground without exposed Blades;

-Passerby are outside the existing thrown-object zone;

-All areas have been thoroughly inspected and all foreign material such as rocks, cans, glass, and general debris has been removed.

NOTE: Where there are grass and weeds high enough to hide debris

that could be struck by the blades, the area should be: inspected and large debris removed, mowed at an intermediate height, inspected, closely with any remaining debris being removed, and mowed again at desired final height. (This will also reduce power requiredto mow, reduce wear and tear on the Mower drivetrain, spread cut material better, eliminate streaking, and make the final cut more uniform.)

(SRM-1)

DANGER! Be particularly careful when transporting the Implement using the tractor. Turn curves or go up or down hills only at a low speed and at a gradual steering angle. Make certain that at least 20% of the tractor’s weight is on the front wheels to maintain safe steerage. Slow down on rough or uneven surfaces.

DANGER! When the Wings are folded for transport, the center of gravity is raised and the possibility of overturn is increased. Drive slowly and use extremecaution when turning on hillsides. Overturning the Implement could cause the Implement to overturn the Tractor and vice versa resulting in serious injury or even death. Never fold wings on a hillside...the Implement may overturn.

FLX15/10 04/06

Safety Section 1-10

© 2006 Alamo Group Inc.

Image 14
Contents FLX15/FLX10 To the OWNER/OPERATOR/DEALER DEALER’S Predelivery Service Guide Table of Contents Safety Section Safety 2006Alamo Group Inc SG-11 Following rules Keep Away from Rotating Elements to prevent entanglement Safety Safety Safety Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety Safety Canister Manual Inside QTY Description Safety Safety Safety Item 16 Patent Numbers Safety Item 23 Multi-Hazard Decal Safety FLX15/10 04/06 Safety Section Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Before Operating this Machine Page Assembly Section Assembly From Shipping Position FLX15/10Connection to Tractor AdjustmentsSetting the Castor Wheels Driveline Attachment Connection to Cutter Connecting Strut To Cutter Assembly Assembly Assembly PRE Customer Delivery Checklist GeneralOperation Section Operation Peligro Mower Standard Equipment And Specifications Operation Operator Requirements Personal Protective Equipment PPETractor Requirements and Capabilities Tractor Safety DevicesTractor Requirements Rops and Seat BeltDrawbar Tractor HorsepowerFront End Weight Tractor HydraulicsPower Take Off PTO Tire SpacingDismounting the Tractor Getting on and OFF the TractorBoarding the Tractor Connecting the FLEX-ARM to the Tractor Starting the TractorConnecting the FLEX-ARM Tongue to the Tractor Connecting the Cutter Precision Hitch to the FLEX-ARM Connecting Mower Hydraulic Lines to the Tractor Setting the Mower Setting Deck Pitch Driveline AttachmentCV Driveline Maximum Angle Check Procedure Constant Velocity CV DrivelinePRE-OPERATION Inspection and Service Lighting Kit RelocatedTractor Pre-Operation Inspection/Service Mower Pre-Operation Inspection/ServiceOperation Operation Cutting Component Inspection Damaged PanDriving the Tractor and Mower Operating the Mower Wings Brake and Differential Lock SettingStarting the Tractor Center Section Transport Lock Pin Driving the Tractor, Flex Arm, and Mower Crossing Ditches and Steep Inclines Operating the TRACTOR,FLEX ARM, and Mower Foreign Debris HazardsBystander/Passersby Precautions Stop Mowing if Passersby are Within 100 Yards UnlessEngaging the Power Take Off PTO PTO RPM and Ground SpeedOperating the Flex Arm & Mower Mowing . S G M Correct Mower Deck Positioning Wrong Mower Deck Positioning Disconnecting FLEX-ARM & Mower from the Tractor Shutting Down the MowerFLEX-ARM & Mower Storage Transporting the TRACTOR, FLEX-ARM, and Mower Tires and Wheels Transporting on Public Roadways Operation Uneven surfaces. STI-1 Hauling the Tractor, Flex Arm and Mower By the following rulesOperation Trouble Shooting Guide Cutter Trouble Shooting Guide FLX15/10 Symptom Problem CorrectionMaintenance Section Maintenance MaintenanceWheel Hub Greasing and Installation Tighten Instructions for 618 Hubs Lubrication Gearboxes Universal Joint Assemblies Lubrication Chart Ramlok Disassembly Procedure Maintenance Warranty Information ONE Last Word FLX15/10 04/06 A101-010C

FLX15, FLX10 specifications

Tiger FLX10 and FLX15 are advanced multi-functional devices that have been designed to cater to diverse industrial and commercial needs. These machines stand out in their respective sectors due to their superior features, cutting-edge technologies, and robust characteristics, making them suitable for various applications.

The Tiger FLX10 brings a host of features that enhance productivity and efficiency. At its core, it integrates a powerful multi-core processor that ensures high-speed performance, allowing users to handle complex tasks with ease. The device is equipped with an intuitive user interface, which simplifies navigation and allows for seamless operation. The FLX10 also boasts impressive multitasking capabilities, enabling users to run multiple applications simultaneously without any lag, thus streamlining workflows.

On the other hand, the FLX15 takes performance a notch higher with its enhanced processing power and memory capacity. It is tailored for more demanding applications, making it ideal for industries requiring high-level data processing and analytics. This model features advanced connectivity options, including Wi-Fi, Bluetooth, and USB ports, facilitating easy integration with other devices and systems. Additionally, the FLX15 supports robust security features, safeguarding sensitive data and ensuring compliance with industry standards.

Both models incorporate advanced technologies that improve functionality. For instance, they utilize state-of-the-art thermal management systems, ensuring optimal performance even in high-temperature environments. The machines are designed with energy efficiency in mind, reducing power consumption while maintaining high output levels, which is a significant consideration for environmentally conscious users.

In terms of durability, both the Tiger FLX10 and FLX15 are constructed using high-quality materials, making them resistant to wear and tear. Their rugged design ensures longevity, minimizing downtime and maintenance costs. Furthermore, these devices come equipped with comprehensive support and warranty options, providing users with peace of mind regarding their investment.

In summary, the Tiger FLX10 and FLX15 are exemplary devices that embody modern technological advancements in industrial applications. With their powerful performance, user-friendly interfaces, advanced connectivity, and robust durability, they stand out as reliable solutions in today’s fast-paced business environment. Both models are well-positioned to meet the evolving demands of various sectors, making them valuable assets for companies looking to enhance their operational efficiency.