Tiger FLX10, FLX15 manual Tighten Instructions for 618 Hubs

Page 92
(SG-15)

MAINTENANCE

MAINTENANCE

2.1 Tighten Instructions for 618 Hubs

Proper Settings for the tapered roller bearings is described in the following procedure. Always use a new cotter pin when making adjustments to the hubs.

1.Tighten the castle nut to 20 foot pounds while turning hub. Then back the nut off 1/2 of a turn. Spin the hub

2or 3 times. While slowly turning hub clockwise, hand tighten the castle nut until castle nut notch lines up with hole in axle. If notch will not line up, back off nut to next notch.

2.Put the cotter pin in the axle hole. Before bending the cotter pin spin the hub. The hub should free wheel from 1 to 2 full turns.

3.If the hub soins the right amount, finish installing the cotter pin by bending the ends.

4.Coat the inside of the dust cap with a thin coat of grease by using your gloved finger. Then install on hub using the right dust cap driver.

5.Wipe off all excess grease from hub and axle.

IMPORTANT: There should not be any drage noticed when spinning a tire installed on a hub. If the axle nut is too tight, the rollers of the wheel bearings will remove the grease from the bearing races, decreasing the life of the bearings.

2.2 Hydraulics

Periodically clean dirt and debris from the bottom side of the depth stop ring.

Inspect hydraulic hoses, fitting and cylinders for wear or leaks. Use a piece of cardboard or wood rather than hands to search for suspected leaks. Replace if necessary.

Before applying pressure to the hydraulic system, be sure all connections are tight and that the hoses are not damaged.

DANGER! Do not operate this Equipment with hydraulic oil leaking. Oil is expensive and its presence could present a hazard. Do not check for leaks with your hand! Use a piece of heavy paper or cardboard. High-pressure oil streams from breaks in the line could penetrate the skin and cause tissue damage including gangrene. If oil does penetrate the skin, have the injury treated immediately by a physician knowledgeable and skilled in this procedure.

FLX15/10 04/06

Maintenance Section 5-4

 

© 2006 Alamo Group Inc.

Image 92
Contents FLX15/FLX10 To the OWNER/OPERATOR/DEALER DEALER’S Predelivery Service Guide Table of Contents Safety Section Safety 2006Alamo Group Inc SG-11 Following rules Keep Away from Rotating Elements to prevent entanglement Safety Safety Safety Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety Safety Canister Manual Inside QTY Description Safety Safety Safety Item 16 Patent Numbers Safety Item 23 Multi-Hazard Decal Safety FLX15/10 04/06 Safety Section Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Before Operating this Machine Page Assembly Section Assembly From Shipping Position FLX15/10Connection to Tractor AdjustmentsSetting the Castor Wheels Driveline Attachment Connection to Cutter Connecting Strut To Cutter Assembly Assembly Assembly PRE Customer Delivery Checklist GeneralOperation Section Operation Peligro Mower Standard Equipment And Specifications Operation Operator Requirements Personal Protective Equipment PPETractor Safety Devices Tractor RequirementsTractor Requirements and Capabilities Rops and Seat BeltTractor Horsepower Front End WeightDrawbar Tractor HydraulicsPower Take Off PTO Tire SpacingDismounting the Tractor Getting on and OFF the TractorBoarding the Tractor Connecting the FLEX-ARM to the Tractor Starting the TractorConnecting the FLEX-ARM Tongue to the Tractor Connecting the Cutter Precision Hitch to the FLEX-ARM Connecting Mower Hydraulic Lines to the Tractor Setting the Mower Setting Deck Pitch Driveline AttachmentCV Driveline Maximum Angle Check Procedure Constant Velocity CV DrivelinePRE-OPERATION Inspection and Service Lighting Kit RelocatedTractor Pre-Operation Inspection/Service Mower Pre-Operation Inspection/ServiceOperation Operation Cutting Component Inspection Damaged PanDriving the Tractor and Mower Operating the Mower Wings Brake and Differential Lock SettingStarting the Tractor Center Section Transport Lock Pin Driving the Tractor, Flex Arm, and Mower Crossing Ditches and Steep Inclines Operating the TRACTOR,FLEX ARM, and Mower Foreign Debris HazardsBystander/Passersby Precautions Stop Mowing if Passersby are Within 100 Yards UnlessEngaging the Power Take Off PTO PTO RPM and Ground SpeedOperating the Flex Arm & Mower Mowing . S G M Correct Mower Deck Positioning Wrong Mower Deck Positioning Disconnecting FLEX-ARM & Mower from the Tractor Shutting Down the MowerFLEX-ARM & Mower Storage Transporting the TRACTOR, FLEX-ARM, and Mower Tires and Wheels Transporting on Public Roadways Operation Uneven surfaces. STI-1 Hauling the Tractor, Flex Arm and Mower By the following rulesOperation Trouble Shooting Guide Cutter Trouble Shooting Guide FLX15/10 Symptom Problem CorrectionMaintenance Section Maintenance MaintenanceWheel Hub Greasing and Installation Tighten Instructions for 618 Hubs Lubrication Gearboxes Universal Joint Assemblies Lubrication Chart Ramlok Disassembly Procedure Maintenance Warranty Information ONE Last Word FLX15/10 04/06 A101-010C

FLX15, FLX10 specifications

Tiger FLX10 and FLX15 are advanced multi-functional devices that have been designed to cater to diverse industrial and commercial needs. These machines stand out in their respective sectors due to their superior features, cutting-edge technologies, and robust characteristics, making them suitable for various applications.

The Tiger FLX10 brings a host of features that enhance productivity and efficiency. At its core, it integrates a powerful multi-core processor that ensures high-speed performance, allowing users to handle complex tasks with ease. The device is equipped with an intuitive user interface, which simplifies navigation and allows for seamless operation. The FLX10 also boasts impressive multitasking capabilities, enabling users to run multiple applications simultaneously without any lag, thus streamlining workflows.

On the other hand, the FLX15 takes performance a notch higher with its enhanced processing power and memory capacity. It is tailored for more demanding applications, making it ideal for industries requiring high-level data processing and analytics. This model features advanced connectivity options, including Wi-Fi, Bluetooth, and USB ports, facilitating easy integration with other devices and systems. Additionally, the FLX15 supports robust security features, safeguarding sensitive data and ensuring compliance with industry standards.

Both models incorporate advanced technologies that improve functionality. For instance, they utilize state-of-the-art thermal management systems, ensuring optimal performance even in high-temperature environments. The machines are designed with energy efficiency in mind, reducing power consumption while maintaining high output levels, which is a significant consideration for environmentally conscious users.

In terms of durability, both the Tiger FLX10 and FLX15 are constructed using high-quality materials, making them resistant to wear and tear. Their rugged design ensures longevity, minimizing downtime and maintenance costs. Furthermore, these devices come equipped with comprehensive support and warranty options, providing users with peace of mind regarding their investment.

In summary, the Tiger FLX10 and FLX15 are exemplary devices that embody modern technological advancements in industrial applications. With their powerful performance, user-friendly interfaces, advanced connectivity, and robust durability, they stand out as reliable solutions in today’s fast-paced business environment. Both models are well-positioned to meet the evolving demands of various sectors, making them valuable assets for companies looking to enhance their operational efficiency.