Tiger FLX15, FLX10 manual Connection to Cutter

Page 39

WARNING!

ASSEMBLY

When attaching the PTO yoke to the Tractor PTO shaft, it is important that the spring activated locking collar slides freely and the locking balls are seated securely in the groove of the PTO shaft. A driveline not attached correctly to the Tractor PTO shaft could slip off and result in personal injury and damage to the cutter.

Remove any tape from the splined shaft, and any booklets from the driveline. Install the shaft spacer (A101-157) onto the splined shaft tight against the steady bearing collar. Slide the clamp collar end of the tractor shaft onto the splined shaft and insert the tapered pin into the yoke. Push the yoke onto the shaft until the groove lines up with the hole and the pin extends through. Tighten the locknut to squeeze the yoke onto the shaft. The protective cone on the steady bearing may need to by unclipped to access the locknut.

6. Connection to Cutter

Remove the hitch clevis from the hitch swivel on the cutter if equipped. Insert the 3/4" bolts into the castor wheels to lock in place.

To align the precision hitch, board the tractor and start the engine. Back the tractor and FLEX-ARM to the cutter until arm hitch tongue is close enough to the cutter swivel. Then use the Flex Arm to extend the precision hitch tongue towards the cutter hitch swivel about a foot. Turn off the tractor engine, place the tractor in park, and set the parking brake before dismounting. Dismount and view to see how far is

needed to go. Keep extending the flex arm in foot 3/4" Bolt increments or as much length needed until holes are

aligned. Once the cutter is connected remove the stabilizer bolts from the castor wheels to free the castor wheels. The stabilizer bolts are to be removed at all times except when backing the flex arm to connect the cutter. Castor wheels should not be left in the lock position after the cutter is attached, the stabilizer bolts are not transport pins, bodily injury or damage to the implement can result if left in.

FLX15/10 04/06

Introduction Section 3-5

© 2006 Alamo Group Inc.

ASSEMBLY

Page 38 Page 40
Image 39
Page 38 Page 40
Contents FLX15/FLX10 To the OWNER/OPERATOR/DEALER DEALER’S Predelivery Service Guide Table of Contents Safety Section Safety 2006Alamo Group Inc SG-11 Following rules Keep Away from Rotating Elements to prevent entanglement Safety Safety Safety Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety Safety Canister Manual Inside QTY Description Safety Safety Safety Item 16 Patent Numbers Safety Item 23 Multi-Hazard Decal Safety FLX15/10 04/06 Safety Section Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Before Operating this Machine Page Assembly Section From Shipping Position FLX15/10 AssemblyAdjustments Setting the Castor WheelsConnection to Tractor Driveline Attachment Connection to Cutter Connecting Strut To Cutter Assembly Assembly Assembly General PRE Customer Delivery ChecklistOperation Section Operation Peligro Mower Standard Equipment And Specifications Operation Personal Protective Equipment PPE Operator RequirementsRops and Seat Belt Tractor Safety DevicesTractor Requirements Tractor Requirements and CapabilitiesTractor Hydraulics Tractor HorsepowerFront End Weight DrawbarTire Spacing Power Take Off PTOGetting on and OFF the Tractor Boarding the TractorDismounting the Tractor Starting the Tractor Connecting the FLEX-ARM to the TractorConnecting the FLEX-ARM Tongue to the Tractor Connecting the Cutter Precision Hitch to the FLEX-ARM Connecting Mower Hydraulic Lines to the Tractor Setting the Mower Driveline Attachment Setting Deck PitchConstant Velocity CV Driveline CV Driveline Maximum Angle Check ProcedureLighting Kit Relocated PRE-OPERATION Inspection and ServiceMower Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceOperation Operation Damaged Pan Cutting Component InspectionDriving the Tractor and Mower Brake and Differential Lock Setting Starting the TractorOperating the Mower Wings Center Section Transport Lock Pin Driving the Tractor, Flex Arm, and Mower Crossing Ditches and Steep Inclines Foreign Debris Hazards Operating the TRACTOR,FLEX ARM, and MowerStop Mowing if Passersby are Within 100 Yards Unless Bystander/Passersby PrecautionsPTO RPM and Ground Speed Engaging the Power Take Off PTOOperating the Flex Arm & Mower Mowing . S G M Correct Mower Deck Positioning Wrong Mower Deck Positioning Shutting Down the Mower Disconnecting FLEX-ARM & Mower from the TractorFLEX-ARM & Mower Storage Transporting the TRACTOR, FLEX-ARM, and Mower Tires and Wheels Transporting on Public Roadways Operation Uneven surfaces. STI-1 By the following rules Hauling the Tractor, Flex Arm and MowerOperation Trouble Shooting Guide Cutter Symptom Problem Correction Trouble Shooting Guide FLX15/10Maintenance Section Maintenance MaintenanceWheel Hub Greasing and Installation Tighten Instructions for 618 Hubs Lubrication Gearboxes Universal Joint Assemblies Lubrication Chart Ramlok Disassembly Procedure Maintenance Warranty Information ONE Last Word FLX15/10 04/06 A101-010C

FLX15, FLX10 specifications

Tiger FLX10 and FLX15 are advanced multi-functional devices that have been designed to cater to diverse industrial and commercial needs. These machines stand out in their respective sectors due to their superior features, cutting-edge technologies, and robust characteristics, making them suitable for various applications.

The Tiger FLX10 brings a host of features that enhance productivity and efficiency. At its core, it integrates a powerful multi-core processor that ensures high-speed performance, allowing users to handle complex tasks with ease. The device is equipped with an intuitive user interface, which simplifies navigation and allows for seamless operation. The FLX10 also boasts impressive multitasking capabilities, enabling users to run multiple applications simultaneously without any lag, thus streamlining workflows.

On the other hand, the FLX15 takes performance a notch higher with its enhanced processing power and memory capacity. It is tailored for more demanding applications, making it ideal for industries requiring high-level data processing and analytics. This model features advanced connectivity options, including Wi-Fi, Bluetooth, and USB ports, facilitating easy integration with other devices and systems. Additionally, the FLX15 supports robust security features, safeguarding sensitive data and ensuring compliance with industry standards.

Both models incorporate advanced technologies that improve functionality. For instance, they utilize state-of-the-art thermal management systems, ensuring optimal performance even in high-temperature environments. The machines are designed with energy efficiency in mind, reducing power consumption while maintaining high output levels, which is a significant consideration for environmentally conscious users.

In terms of durability, both the Tiger FLX10 and FLX15 are constructed using high-quality materials, making them resistant to wear and tear. Their rugged design ensures longevity, minimizing downtime and maintenance costs. Furthermore, these devices come equipped with comprehensive support and warranty options, providing users with peace of mind regarding their investment.

In summary, the Tiger FLX10 and FLX15 are exemplary devices that embody modern technological advancements in industrial applications. With their powerful performance, user-friendly interfaces, advanced connectivity, and robust durability, they stand out as reliable solutions in today’s fast-paced business environment. Both models are well-positioned to meet the evolving demands of various sectors, making them valuable assets for companies looking to enhance their operational efficiency.
Top Page Image Contents