Walker S14 manual Maintenance Instructions

Page 74

Maintenance Instructions

ADJUSTMENTS

2.Securely block the tractor up so the drive tires are off the ground.

3.Adjust the tracking adjustment nuts at the front of both control rods so that 2 or 3 threads are visible, then loosen the jam nuts on the ball joints at the back of the control rods.

ControlArm

ControlRods

Transmission Control Rod and Arm Location

(Front Body Hidden for Clarity)

Ball Joint

Maximum Speed

Adjustment Set Screw

 

Jam Nut

 

Control Rod

Locating Stud

Transmission

Control Arm

Tracking Adjustment Nut

(Adjusts Length of Control Rod)

Tracking Adjustment Components

WARNING

The following adjustments are made with the engine running. Keep all body parts and tools away from rotating and hot components, and secure all loose cloth- ing.

4.With the body lowered and the FSC in NEU- TRAL-PARK,start the engine. With the engine at normal operating speed, check for movement of the drive wheels.

5.Lift the body to access the steering adjustment components.

NOTE: It may be necessary to tighten the FSC friction adjustment if the transmissions are moved out of neutral when the body is raised. Refer to Step 7 - Forward Speed Control Friction Adjustment later in this section for location of the FSC friction adjustment nut.

6.Using a wrench on one tracking adjustment nut, rotate the control rod clockwise just until the wheel on that side begins to move forward. Then, counting the turns required, rotate the control rod counterclockwise just until the wheel stops and then begins to move in re- verse. Rotate the control rod back clockwise half the number of turns required to make the wheel go from moving forward to reverse. The transmission is now centered in the neutral win- dow. Tighten the jam nut on the ball joint and repeat the same procedure on the other trans- mission.

7.Turn off the engine, and then lower the drive tires onto the ground.

70

Image 74
Contents Operator’s Manual Foreword Table of Contents Maintenance Schedule Chart Important Tips for Care Identifying Number Locations General InformationGlossary Fill In By PurchaserServicing of Engine and Drivetrain Components Electrical System SpecificationsEngine TransmissionTire Pressure PSI KPA Blade DriveTire Size Width in. cm Dimensions Tractor and Mower Length in. cmWeight lb kg Height in. cmSeat Mower DeckDrive Belts Component Identification Front View and Right Side ViewRear View and Left Side View Top View Body Raised Do not mow with bystanders in the area Safety Instructions Before OperatingBefore Operating Safety Instructions Before Operating Safety Instructions Operating Safety Instructions Operating Safety Instructions Maintenance Location Gearbox Cover Gear Drive Decks Only Part Number Safety InstructionsLocation Top of Fuel Tank Part Number Location Chassis Member Behind Transaxles Part NumberLocation Deck Gearbox Cover Part Number Location Each End of Mower Deck Part NumberLocation Deck Discharge Shield SD Decks Only Part Number Location LH Fender Part Number Location RH Fender Part NumberBattery Service Assembly InstructionsSetup Instructions Deck Caster Wheels Installation Battery InstallationBattery Installation Mower Deck Assembly Batteries Produce Explosive GasesPTO Shaft Guard Installation Deck Caster Wheel InstallationDischarge Shield Installation On Side Discharge Deck Deck Counterweight Spring Installation Deck InstallationMower Deck Installation PTO Shaft ConnectionDeck Leveling Machine must be shut off during this procedureDeck Leveling Fill Fuel Tank Refer to Lubrication for Transaxle LubricationBlades in Maintenance Instructions Control IDENTIFICATION, LOCATION, and Function Ignition Switch Key PositionsOperating Instructions Engine ChokeSteering Levers Engine ThrottleChoke and Throttle Location Forward Speed Control FSC Blade Clutch PTOParking Brake Hydro Lockout Arm LocationHourmeter Left Wheel Steering Leverright Wheel Operating Controls Top View from Drivers Point of ViewEngaged Adjusting Ground Speed and SteeringStarting the Engine Forward Speed Control Friction Adjustment Beginning Recommendations areCorrect Operator Hand Position On the Controls Blade Clutch Engaged Stopping the MachineHydro Lockout Arm Freewheel Position Cutting Height AdjustmentTransaxle Lockouts Hydro Lockout Arm Normal Operating PositionRecommendations for Mowing Side Discharge Deflector Shield Lowest Position No Driving ZoneRecommendations for TILT-UP Deck OPERATION/TRANSPORT GHS Model Only GHS Flow and ComponentsGeneral Information Rotating Blower BladesClogging Checklist ForwardFull Signal Horn Using the Tilt-Up DeckPowerfil Tailgate Dumping Dumping Catcher into Dump Bag Using the Dump BagPositioning Dump Bag on Catcher Service Item 100 400 Every Maintenance InstructionsMaintenance procedures requiring special training or HoursImportant Tips for Care of the Subaru Engine Not Screwed LubricationEach USE Oil Drain Location View from Lower Right Side of Tractor Grease Fitting and Oil Point LubricationDeck and Carrier Frame Illustrated Maintenance Instructions Expansion Reservoir Location Mower Deck Gearbox LubricationTransaxle Lubrication Guard Engine Air Cleaner System Components CleaningAir Cleaner Components Shown with Cover Removed Air Filter Element Replacement Fuel Filter and Fuel Shut-off Valve Location Proper Orientation of Air Cleaner CoverFuel Filter Cooling System Airflow Keep Rotating Engine Cooling Air Intake Screen CleanCooling Air Intake Screen GHS Exhaust Screen Battery Transaxle HousingTransaxle Housing and Cooling Fins Transaxle Cooling FansWheel Nut Torque Charging the BatteryTire Pressure Sharpen Mower BladesMower Blade Profile for Sharpening Blade Balanced on Magnetic Wall-Mounted BalancerIgnition Drive BeltsSpark Plug Forward Speed Control Friction Lock REPLACING/REPAIRING Belt LocationsEngine Belt Engaged Engine BeltEngine Belt Disengaged PTO Drive Belt Engaged PTO Drive BeltPTO Drive Belt Disengaged Ground Drive Belt Ground Drive Belt Assembly DisengagedGround Drive Belt Assembly Engaged PTO Shear Pin Blade Overload Shear BoltsCutting Blade Shear Bolts Mower Blades Transmission Control AdjustmentsSteering Lever Position Adjustment Lever AlignmentCorrect FSC Lever NEUTRAL-PARK Position Steering Handles AdjustmentFSC Lever Position Adjustment Maintenance Instructions FSC Neutral Switch Location FSC Friction Adjustment Test FSC Friction Adjustment NutPTO Clutch Engaged PTO Clutch Disengaged Blade Brake Band Adjustment Blade Brake Band Adjustment Clutch Disengaged Side View of Catcher Box Adjusting the Grass-PakSwitchPinch Point Spring Loaded Door With a little advance warning before overfillingOperator’s Notes Operator’s Notes Limited Warranty For Walker Model S14 Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970

S14 specifications

The Walker S14 is an innovative piece of technology designed to enhance mobility and independence for individuals facing mobility challenges. This advanced mobility device integrates cutting-edge features and technologies to deliver a safe and comfortable user experience.

One of the standout characteristics of the Walker S14 is its lightweight yet robust design. Constructed from high-quality materials, the walker provides durability without sacrificing portability. It can easily be maneuvered both indoors and outdoors, making it suitable for various environments.

A significant technological advancement in the Walker S14 is its adjustable height feature. Users can customize the walker to their preferred height, ensuring optimal support and reducing strain on the body. This feature is particularly beneficial for individuals with varying mobility needs, as it promotes a proper walking posture.

Safety is a top priority in the design of the Walker S14. It is equipped with a reliable braking system that enhances stability when stationary. The walker features ergonomic hand grips that provide comfort and reduce the risk of slipping. Additionally, its non-slip wheels are designed to provide a reliable grip on various surfaces, contributing to a safer walking experience.

In terms of storage and convenience, the Walker S14 includes a built-in storage pouch, allowing users to carry personal items or essential belongings. This feature is particularly useful for users who wish to maintain their independence while being able to access their belongings easily.

The Walker S14 is also praised for its sleek and modern aesthetic. With a variety of color options, users can choose a design that reflects their personality while still benefiting from the practicality of the mobility device.

Moreover, the Walker S14 is designed for easy folding and portability. Whether for storage or transport, users can quickly collapse the walker to fit it in tight spaces or vehicles without any hassle.

Overall, the Walker S14 combines innovative technology, user-centric design, and robust safety features to provide an unparalleled walking experience. It empowers individuals with mobility challenges to navigate their surroundings with confidence, fostering independence and a better quality of life.