Walker S14 manual General Information, Rotating Blower Blades

Page 43

Operating Instructions

General Information

The Grass Handling System (GHS) consists of a rear discharge mower deck connected to a 12.5 in. (32 cm) blower and a rear mounted grass catcher with 7.0 bushel (246 liters) capacity. The GHS blow- er operates any time the mower blade clutch is en- gaged and moves grass through the rear discharge deck chute into the grass catcher. Blower airflow is exhausted out the back of the grass catcher, through a filtering screen. When the grass catcher is full and needs to be emptied, a “full” signal horn alerts the operator. When the “full” signal horn sounds, it is important to stop mowing to prevent overfilling and clogging of the blower system.

IMPORTANT: Normally, the GHS blower operates with no maintenance or cleaning required. However, under certain operating conditions, the inside of the blower housing may accumulate a deposit of dirt, causing wear and binding of the blower wheel. Normally, dirt buildup occurs when mowing a com­ bination of dirty and damp grass, especially in the springtime. When operating in these condi­tions, check the blower wheel frequently for binding and clean the blower housing as required. Refer to CLEANING the GHS Blower in Maintenance

Instructions.

NOTE: In Autumn, when using the GHS mower to vacuum leaves, it is recommended to raise the front of the mower deck 2 to 3 notches [1 to 1-1/2 in. (25 to 38 mm)] higher than the rear. This will avoid “bulldozing” leaves, particularly when the leaves are piled in a thick layer. To make this ad­justment, the hitch pins in the two (2) front deck support pins are repositioned 2 to 3 notches higher while leaving the rear pins in their original position.

DANGER

NEVER operate the GHS catcher with the back door open. Objects may be thrown out the back of the catcher with sufficient force to cause serious injury to bystand­ers or property damage.

DANGER

ROTATING BLOWER BLADES

NEVER operate the GHS blower with the blower discharge chute uncovered (grass catcher in the dump position) since dangerous projectiles may be thrown. NEVER put hands into the blower discharge chute for any reason. Use a stick or similar instrument to remove any material if clogging has occurred.

CAUTION

NEVER leave grass clippings in the grass catcher after mowing. Damp clippings generate heat as they decompose. This MAY cause spontaneous combustion.

39

Image 43
Contents Operator’s Manual Foreword Table of Contents Maintenance Schedule Chart Important Tips for Care Fill In By Purchaser General InformationGlossary Identifying Number LocationsServicing of Engine and Drivetrain Components Transmission SpecificationsEngine Electrical SystemTire Size Blade DriveTire Pressure PSI KPA Height in. cm Dimensions Tractor and Mower Length in. cmWeight lb kg Width in. cmDrive Belts Mower DeckSeat Front View and Right Side View Component IdentificationRear View and Left Side View Top View Body Raised Before Operating Safety Instructions Before OperatingDo not mow with bystanders in the area Safety Instructions Before Operating Safety Instructions Operating Safety Instructions Operating Safety Instructions Maintenance Location Chassis Member Behind Transaxles Part Number Safety InstructionsLocation Top of Fuel Tank Part Number Location Gearbox Cover Gear Drive Decks Only Part NumberLocation Deck Discharge Shield SD Decks Only Part Number Location Each End of Mower Deck Part NumberLocation Deck Gearbox Cover Part Number Location RH Fender Part Number Location LH Fender Part NumberSetup Instructions Assembly InstructionsBattery Service Batteries Produce Explosive Gases Battery InstallationBattery Installation Mower Deck Assembly Deck Caster Wheels InstallationDischarge Shield Installation On Side Discharge Deck Deck Caster Wheel InstallationPTO Shaft Guard Installation PTO Shaft Connection Deck InstallationMower Deck Installation Deck Counterweight Spring InstallationDeck Leveling Machine must be shut off during this procedureDeck Leveling Refer to Lubrication for Transaxle Lubrication Fill Fuel TankBlades in Maintenance Instructions Engine Choke Ignition Switch Key PositionsOperating Instructions Control IDENTIFICATION, LOCATION, and FunctionBlade Clutch PTO Engine ThrottleChoke and Throttle Location Forward Speed Control FSC Steering LeversHydro Lockout Arm Location Parking BrakeHourmeter Operating Controls Top View from Drivers Point of View Left Wheel Steering Leverright WheelStarting the Engine Adjusting Ground Speed and SteeringEngaged Beginning Recommendations are Forward Speed Control Friction AdjustmentCorrect Operator Hand Position On the Controls Stopping the Machine Blade Clutch EngagedHydro Lockout Arm Normal Operating Position Cutting Height AdjustmentTransaxle Lockouts Hydro Lockout Arm Freewheel PositionRecommendations for Mowing No Driving Zone Side Discharge Deflector Shield Lowest PositionRecommendations for TILT-UP Deck OPERATION/TRANSPORT GHS Flow and Components GHS Model OnlyRotating Blower Blades General InformationForward Clogging ChecklistPowerfil Using the Tilt-Up DeckFull Signal Horn Tailgate Dumping Positioning Dump Bag on Catcher Using the Dump BagDumping Catcher into Dump Bag Hours Maintenance InstructionsMaintenance procedures requiring special training or Service Item 100 400 EveryImportant Tips for Care of the Subaru Engine Each USE LubricationNot Screwed Grease Fitting and Oil Point Lubrication Oil Drain Location View from Lower Right Side of TractorDeck and Carrier Frame Illustrated Maintenance Instructions Transaxle Lubrication Mower Deck Gearbox LubricationExpansion Reservoir Location Guard Air Cleaner Components Shown with Cover Removed CleaningEngine Air Cleaner System Components Air Filter Element Replacement Fuel Filter Proper Orientation of Air Cleaner CoverFuel Filter and Fuel Shut-off Valve Location Cooling Air Intake Screen Keep Rotating Engine Cooling Air Intake Screen CleanCooling System Airflow GHS Exhaust Screen Transaxle Cooling Fans Transaxle HousingTransaxle Housing and Cooling Fins BatterySharpen Mower Blades Charging the BatteryTire Pressure Wheel Nut TorqueBlade Balanced on Magnetic Wall-Mounted Balancer Mower Blade Profile for SharpeningSpark Plug Drive BeltsIgnition Forward Speed Control Friction Lock Belt Locations REPLACING/REPAIRINGEngine Belt Disengaged Engine BeltEngine Belt Engaged PTO Drive Belt Disengaged PTO Drive BeltPTO Drive Belt Engaged Ground Drive Belt Assembly Engaged Ground Drive Belt Assembly DisengagedGround Drive Belt Cutting Blade Shear Bolts Blade Overload Shear BoltsPTO Shear Pin Mower Blades Lever Alignment AdjustmentsSteering Lever Position Adjustment Transmission ControlFSC Lever Position Adjustment Steering Handles AdjustmentCorrect FSC Lever NEUTRAL-PARK Position Maintenance Instructions FSC Neutral Switch Location FSC Friction Adjustment Nut FSC Friction Adjustment TestPTO Clutch Engaged PTO Clutch Disengaged Blade Brake Band Adjustment Blade Brake Band Adjustment Clutch Disengaged With a little advance warning before overfilling Adjusting the Grass-PakSwitchPinch Point Spring Loaded Door Side View of Catcher BoxOperator’s Notes Operator’s Notes Limited Warranty For Walker Model S14 Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970

S14 specifications

The Walker S14 is an innovative piece of technology designed to enhance mobility and independence for individuals facing mobility challenges. This advanced mobility device integrates cutting-edge features and technologies to deliver a safe and comfortable user experience.

One of the standout characteristics of the Walker S14 is its lightweight yet robust design. Constructed from high-quality materials, the walker provides durability without sacrificing portability. It can easily be maneuvered both indoors and outdoors, making it suitable for various environments.

A significant technological advancement in the Walker S14 is its adjustable height feature. Users can customize the walker to their preferred height, ensuring optimal support and reducing strain on the body. This feature is particularly beneficial for individuals with varying mobility needs, as it promotes a proper walking posture.

Safety is a top priority in the design of the Walker S14. It is equipped with a reliable braking system that enhances stability when stationary. The walker features ergonomic hand grips that provide comfort and reduce the risk of slipping. Additionally, its non-slip wheels are designed to provide a reliable grip on various surfaces, contributing to a safer walking experience.

In terms of storage and convenience, the Walker S14 includes a built-in storage pouch, allowing users to carry personal items or essential belongings. This feature is particularly useful for users who wish to maintain their independence while being able to access their belongings easily.

The Walker S14 is also praised for its sleek and modern aesthetic. With a variety of color options, users can choose a design that reflects their personality while still benefiting from the practicality of the mobility device.

Moreover, the Walker S14 is designed for easy folding and portability. Whether for storage or transport, users can quickly collapse the walker to fit it in tight spaces or vehicles without any hassle.

Overall, the Walker S14 combines innovative technology, user-centric design, and robust safety features to provide an unparalleled walking experience. It empowers individuals with mobility challenges to navigate their surroundings with confidence, fostering independence and a better quality of life.