Walker S14 manual Drive Belts, Spark Plug, Ignition

Page 64

Maintenance Instructions

CHECKING/SERVICING

Drive Belts

Raise the body and inspect the condition of the three

(3)drive belts after every 25 hours of operation -- engine, PTO drive, and ground drive. If the belts show signs of cracking or deteriorating, the belts should be replaced. Refer to REPLACING/RE- PAIRING the Drive Belts in this section.

Mower Deck Gearbox Oil Seals

The mower deck gearbox seals should be inspected every 25 hours for evidence of oil leaking; particu- larly the lower oil seal on the blade drive gearbox. This seal is protected by the trash guard on the blade hub and seal protector plate on the housing, but is still vulnerable to seal damage due to operating in an adverse environment. The mower blade must be removed for inspection of the seal, so it is recom- mended to inspect the gearbox seals when blades are removed for sharpening. If an oil leak is noted, the seal should be replaced and the gearbox as- sembly relubricated. Refer to LUBRICATION for Mower Deck Gearbox Lubrication in this section.

Spark Plug

Every 100 hours, remove the spark plug, inspect, clean, and reset the gap (or replace with a new plug). Clean spark plug with a wire brush. If the electrodes are burned short or pitted, replace the plug (refer to Specifications for the proper type of replacement plug). Check the spark plug gap with a wire-type feeler gauge and set the gap between 0.028 and 0.032 in. (0.7 and 0.8 mm). Reinstall and tighten to 17 lb·ft (23 N·m).

Ignition

The Subaru engine is equipped with an electronic ignition. No breaker points, maintenance, or adjust- ments are necessary with this system. Contact an authorized Subaru engine dealer in case of ignition failure.

Fuel Lines and Clamps

Every year, inspect the fuel line from the tank to engine for deterioration or damage. Also, inspect the fuel line clamps for tightness. Good preven- tive maintenance calls for complete replacement of fuel lines and clamps every two (2) years.

Blade Brake Action

WARNING

It is important to check and maintain blade brake action for safe operation of the ma- chine.

Check the function of the cutter blade brake and blower brake by engaging the blade clutch (PTO), operating the engine at full throttle, then disengaging the clutch and measuring how quickly the blades stop. Watch the rotation of the blade drive shaft and blower pulley as a visual indication that movement has stopped. If the brake is working properly, all rotation will stop five (5) seconds after disen- gagement of the clutch. If the brake system mal- functions - blades do not stop in five (5) seconds - adjust or repair the brake before operating the mower. Refer to Blade Brake Band Adjustment in ADJUSTMENTS in this section, or contact your au- thorized Walker dealer for this service.

60

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Operator’s Manual Foreword Table of Contents Maintenance Schedule Chart Important Tips for Care General Information GlossaryIdentifying Number Locations Fill In By PurchaserServicing of Engine and Drivetrain Components Specifications EngineElectrical System TransmissionTire Size Blade DriveTire Pressure PSI KPA Dimensions Tractor and Mower Length in. cm Weight lb kgWidth in. cm Height in. cmDrive Belts Mower DeckSeat Component Identification Front View and Right Side ViewRear View and Left Side View Top View Body Raised Before Operating Safety Instructions Before OperatingDo not mow with bystanders in the area Safety Instructions Before Operating Safety Instructions Operating Safety Instructions Operating Safety Instructions Maintenance Safety Instructions Location Top of Fuel Tank Part NumberLocation Gearbox Cover Gear Drive Decks Only Part Number Location Chassis Member Behind Transaxles Part NumberLocation Deck Discharge Shield SD Decks Only Part Number Location Each End of Mower Deck Part NumberLocation Deck Gearbox Cover Part Number Location LH Fender Part Number Location RH Fender Part NumberSetup Instructions Assembly InstructionsBattery Service Battery Installation Battery Installation Mower Deck AssemblyDeck Caster Wheels Installation Batteries Produce Explosive GasesDischarge Shield Installation On Side Discharge Deck Deck Caster Wheel InstallationPTO Shaft Guard Installation Deck Installation Mower Deck InstallationDeck Counterweight Spring Installation PTO Shaft ConnectionDeck Leveling Machine must be shut off during this procedureDeck Leveling Fill Fuel Tank Refer to Lubrication for Transaxle LubricationBlades in Maintenance Instructions Ignition Switch Key Positions Operating InstructionsControl IDENTIFICATION, LOCATION, and Function Engine ChokeEngine Throttle Choke and Throttle Location Forward Speed Control FSCSteering Levers Blade Clutch PTOParking Brake Hydro Lockout Arm LocationHourmeter Left Wheel Steering Leverright Wheel Operating Controls Top View from Drivers Point of ViewStarting the Engine Adjusting Ground Speed and SteeringEngaged Forward Speed Control Friction Adjustment Beginning Recommendations areCorrect Operator Hand Position On the Controls Blade Clutch Engaged Stopping the MachineCutting Height Adjustment Transaxle LockoutsHydro Lockout Arm Freewheel Position Hydro Lockout Arm Normal Operating PositionRecommendations for Mowing Side Discharge Deflector Shield Lowest Position No Driving ZoneRecommendations for TILT-UP Deck OPERATION/TRANSPORT GHS Model Only GHS Flow and ComponentsGeneral Information Rotating Blower BladesClogging Checklist ForwardPowerfil Using the Tilt-Up DeckFull Signal Horn Tailgate Dumping Positioning Dump Bag on Catcher Using the Dump BagDumping Catcher into Dump Bag Maintenance Instructions Maintenance procedures requiring special training orService Item 100 400 Every HoursImportant Tips for Care of the Subaru Engine Each USE LubricationNot Screwed Oil Drain Location View from Lower Right Side of Tractor Grease Fitting and Oil Point LubricationDeck and Carrier Frame Illustrated Maintenance Instructions Transaxle Lubrication Mower Deck Gearbox LubricationExpansion Reservoir Location Guard Air Cleaner Components Shown with Cover Removed CleaningEngine Air Cleaner System Components Air Filter Element Replacement Fuel Filter Proper Orientation of Air Cleaner CoverFuel Filter and Fuel Shut-off Valve Location Cooling Air Intake Screen Keep Rotating Engine Cooling Air Intake Screen CleanCooling System Airflow GHS Exhaust Screen Transaxle Housing Transaxle Housing and Cooling FinsBattery Transaxle Cooling FansCharging the Battery Tire PressureWheel Nut Torque Sharpen Mower BladesMower Blade Profile for Sharpening Blade Balanced on Magnetic Wall-Mounted BalancerSpark Plug Drive BeltsIgnition Forward Speed Control Friction Lock REPLACING/REPAIRING Belt LocationsEngine Belt Disengaged Engine BeltEngine Belt Engaged PTO Drive Belt Disengaged PTO Drive BeltPTO Drive Belt Engaged Ground Drive Belt Assembly Engaged Ground Drive Belt Assembly DisengagedGround Drive Belt Cutting Blade Shear Bolts Blade Overload Shear BoltsPTO Shear Pin Mower Blades Adjustments Steering Lever Position AdjustmentTransmission Control Lever AlignmentFSC Lever Position Adjustment Steering Handles AdjustmentCorrect FSC Lever NEUTRAL-PARK Position Maintenance Instructions FSC Neutral Switch Location FSC Friction Adjustment Test FSC Friction Adjustment NutPTO Clutch Engaged PTO Clutch Disengaged Blade Brake Band Adjustment Blade Brake Band Adjustment Clutch Disengaged Adjusting the Grass-PakSwitch Pinch Point Spring Loaded DoorSide View of Catcher Box With a little advance warning before overfillingOperator’s Notes Operator’s Notes Limited Warranty For Walker Model S14 Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970

S14 specifications

The Walker S14 is an innovative piece of technology designed to enhance mobility and independence for individuals facing mobility challenges. This advanced mobility device integrates cutting-edge features and technologies to deliver a safe and comfortable user experience.

One of the standout characteristics of the Walker S14 is its lightweight yet robust design. Constructed from high-quality materials, the walker provides durability without sacrificing portability. It can easily be maneuvered both indoors and outdoors, making it suitable for various environments.

A significant technological advancement in the Walker S14 is its adjustable height feature. Users can customize the walker to their preferred height, ensuring optimal support and reducing strain on the body. This feature is particularly beneficial for individuals with varying mobility needs, as it promotes a proper walking posture.

Safety is a top priority in the design of the Walker S14. It is equipped with a reliable braking system that enhances stability when stationary. The walker features ergonomic hand grips that provide comfort and reduce the risk of slipping. Additionally, its non-slip wheels are designed to provide a reliable grip on various surfaces, contributing to a safer walking experience.

In terms of storage and convenience, the Walker S14 includes a built-in storage pouch, allowing users to carry personal items or essential belongings. This feature is particularly useful for users who wish to maintain their independence while being able to access their belongings easily.

The Walker S14 is also praised for its sleek and modern aesthetic. With a variety of color options, users can choose a design that reflects their personality while still benefiting from the practicality of the mobility device.

Moreover, the Walker S14 is designed for easy folding and portability. Whether for storage or transport, users can quickly collapse the walker to fit it in tight spaces or vehicles without any hassle.

Overall, the Walker S14 combines innovative technology, user-centric design, and robust safety features to provide an unparalleled walking experience. It empowers individuals with mobility challenges to navigate their surroundings with confidence, fostering independence and a better quality of life.
Top Page Image Contents