Woods Equipment 111877 Hose Kit, Hydraulic Installation, General Description, Install Hose Hanger

Page 19
1023596 HOSE KIT

1023596 HOSE KIT

General Description

These instructions are for operating the LU126 loader using the tractor hydraulic remote control lever. To use this hydraulic connection, the tractor must be equipped with four tractor hydraulic couplers.

NOTE: Male quick couplers (3) for connection to trac- tor are NOT included with the hose kit but are avail- able as service parts.

Install Hose Fittings

1.Attach elbow (2) and male quick coupler (3) to each loader supply hose (1).

2.Connect loader supply hoses to loader steel feedlines. Following pattern shown in Figure 8.

1.1023472 Hose, 170" x 3/4 JICM x 3/4 JICM

2.313053 Elbow, 3/4 JICF x 1/2 NPTM

3.66511 Quick coupler, male 1/2

Figure 28. LU126 Loader Supply Hose Connection

Route Hydraulic Hoses

Route hoses along loader mount, under the right side of the operator’s platform, and over the rear axle.

Be sure to avoid contact with 3-point linkage, brake pedals, and other moveable tractor components.

Hoses must be routed so they are not pinched, bent sharply, or chafed during operation. Hoses must not interfere with any tractor control operation or contact any moving parts.

Connect hydraulic hoses to tractor hydraulic couplers.

Install Hose Hanger

1.Install hose hanger bracket beneath right side of the operator’s platform as shown in Figure 29. Use cap screw, flat washers, and lock nut as shown in Figure 29.

2.Route hoses through support and secure with lock pin (12).

+26(￿￿￿￿￿￿￿

+$1*(5

Figure 29. Hose Hanger Installed

4.58033 Hose hanger bracket

12.58047 1/4 x 2-1/2 Lock pin

15.6778 5/16 NC Lock nut

16.6250 5/16 NC x 1-1/4 HHCS

17.4378 5/16 Standard flat washer

MAN0064 (Rev. 7/20/2007)

Hydraulic Installation 19

 

 

Image 19
Contents includes Hose Kits 57923 Loader safety111877 LOADER MOUNTING KIT for 1020, 1027, LU126 LoadersModel 2IntroductionTO THE DEALER TO THE OWNERATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED SafetySAFETY RULES INSTALLATIONLOADER MOUNT INSTALLATION 4 Mount InstallationTRACTOR PREPARATION Figure 2. Left rear Mount Installed Mount InstallationInstall Right and Left Rear Mounts Figure 1. Rear Mount InstallationInstall Front Mount 6 Mount InstallationInstall Right and Left Side rails Cap Screw Install Grill Guard OptionalTORQUE SPECIFICATIONS Torque Hardware8 Mount Installation 57923 HOSE KIT Hydraulic InstallationHOSE KIT INSTALLATION Install Hose FittingsRoute Hydraulic Hoses 10 Hydraulic InstallationInstall Hose Hanger 59723 Hose Kit57923 Hose Kit Verify Control Movements 1001420 HOSE KIT 12 Hydraulic InstallationInstall Adapter Plate Figure 13. 2-SpoolControl Valve Installed Typical1001420 Hose Kit Install Hoses 1001420 Hose Kit Install Hose Hanger 14 Hydraulic InstallationConnect Loader Feedline Hoses 1001420 Hose Kit Verify Control Movements 1023582 HOSE KIT 16 Hydraulic Installation1023582 Hose Kit Install Hoses 1023582 Hose Kit Connect Loader Feedline Hoses 18 Hydraulic InstallationVerify Control Movements 1023596 HOSE KIT 1023596 Hose Kit Verify Control Movements 20 Hydraulic InstallationDESCRIPTION Parts111877 LOADER MOUNTING KIT PART1020/1027 LOADERS 22 PartsREF PART QTY LU126 LOADER 10120/1027 LOADERS 24 PartsInstallations BOLT TORQUE CHARTSAE SERIES A TORQUE CHART CHARTSAE Bolt Thread Sizes BOLT SIZE CHART26Appendix ABBREVIATIONSOregon, Illinois 61061 USA 800-319-6637tel WARRANTYWoods Equipment Company 2606 South Illinois Route Post Office BoxF-8494Rev. 6/23/2005