Yard Machines OEM-190-032 warranty Model Series 600-649 All 800 series Cub Cadet 11C & 13C

Page 10

4

Assembly

Model Series

600-649 &

All 800 series

Cub Cadet 11C & 13C

WARNING

Before installing attachment, place tractor on a firm and level surface. Place the PTO in

the disengaged

(OFF) position, set the parking brake, shut engine off and remove key to prevent unintended starting.

Mounting the Idler Assembly

(42, 46, 50, 54 inch Decks

with Electric PTO)

If you’re mounting this snow thrower attachment to a tractor equipped with any deck other than a 42, 46, 50 or 54-inch deck with electric PTO, proceed to Mounting

the Undercarriage Assembly (all tractors).

However, if you’re mounting this snow thrower attach- ment to a tractor equipped with a 42, 46, 50 or 54-inch deck with electric PTO, proceed as follows:

NOTE: If you engage your tractor’s cutting deck by using your left hand to pivot a lever forward, your tractor has a Manual PTO. If you engage your tractor’s cutting deck by pulling outward on a small knob located on the tractor’s dash, your tractor has an Electric PTO.

1.Remove the flange nut and washer noted in Figure 8, which secures the double-idler bracket to the undercarriage. Leave the Shoulder Spacer in place.

2.Attach the idler assembly (packaged separately) over the hex screw and shoulder spacer on the surface of the undercarriage. See Figure 8.

3.Fasten the idler bracket to the undercarriage with the hardware just removed. See Figure 8.

4.Attach one end of the extension spring (732-0594A) to the hole in the idler assembly just mounted and the opposite end of the extension spring to the keeper pin as illustrated in Figure 8.

5.Position the upper v-belt (754-0371A) as illustrated in Figure 9.

NOTE: For a complete detailed diagram of how to route the upper v-belt, see Routing The Upper Drive Belt beginning at the top of page 18.

NOTE: Proceed to the top of page 12 for continued installation instructions for the 600, 800, 11C & 13C model series.

Extension Spring

Flange Lock Nut

& Flat Washer

Idler Bracket & Pulley

Shoulder Spacer

Figure 8

Upper V-belt (754-0371A)

Figure 9

10

Image 10
Contents OPERATOR’S Manual Finding and Recording Model Number Customer SupportRider Model Identification FastAttach Snow Thrower Attachment To The OwnerDetermine The Model Your Rider Sample Model NumberTrainingPreparation Your Responsibility Restrict the useYour Responsibility Maintenance & StorageOperation Do not modify engineCarton Contents Contents of Carton Manual PTO Tractors equipped with MountingIdler Pulley and Pin Or 42-inch deck onlyMounting the Belt Keeper AssemblyReversing Idler Assembly Hardware With a 46-inch deck only42, 46, 50, 54 inch Decks With Electric PTO Undercarriage Assembly all tractorsModel Series 600-649 All 800 series Cub Cadet 11C & 13C Upper V-belt 754-0371AUndercarriage Assembly Model Series 600-649 Cub Cadet 11C 38 & 42-inchUpper Drive Belt Reference Chart Mounting Undercarriage AssemblyDeck Size Lift Arm Clevis Pin Model Series 700-799 Bracket Undercarriage AssemblyBracket Assembly PTO Cable Belt Keeper Pin Flange Lock Nut & Washer SlottedPin Mounting the Undercarriage AssemblyRemove Nut Hairpin Clip Attaching Lift Handle Assembling ControlsAttaching the Chute Directional Control Attaching the ReflectorsAttaching the Support Tubes Mounting Auger HousingInset a Inset B Various Models Belt RoutingAll electric PTO Decks 42, 46, 50Left Side Undercarriage Routing the Upper Drive Belt Older Style TractorsRouting the Lower Drive Belt All Tractors Models Spindle Pulley Double-Idler Bracket Right SideChute Directional Control Engaging the Augers ImpellerQuickly Operation Tire Chain Kit NumberLift Adjustment AdjustmentsMaking Adjustments Lower Chute Crank Support Bracket AdjustmentBefore lubricating Repairing, or MaintenanceMaintenance Lubrication Chute Directional ControlPage Snow Thrower 40 B Snow Thrower Attachment 12 8 Belt Guard Page Page MANUFACTURER’S Limited Warranty for