Yard Machines OEM-190-032 Bracket Undercarriage Assembly, Model Series 700-799, Bracket Assembly

Page 14

5

Bracket &

Undercarriage

Assembly

Model Series

700-799

WARNING

Before installing attachment, place tractor on a firm and level surface. Place the PTO in

the disengaged

(OFF) position, set the parking brake, shut engine off and remove key to prevent unintended starting.

Bracket Assembly

WARNING: Before installing attach- ment, place tractor on a firm and level surface. Place the PTO in the disen- gaged (OFF) position, set the parking brake, shut engine off and remove key to prevent unintended starting.

NOTE: Your tractor’s cutting deck, PTO belt and front deck stabilizer bracket must be removed prior to mounting the snow thrower attachment. Refer to your tractor’s Operator’s Manual for detailed instructions. If your tractor is equipped with any front-end accessory

(i.e. front bumper kit), it must also be removed.

1.Install a shoulder screw (738-0143) and flange lock nut (712-04065) in the top front hole of each snow thrower assembly bracket as in Figure 17.

2.Mount snow thrower assembly brackets (683-04214 & 683-04215) to your tractor using the loose hardware included (Hex Screw 710-0514 & Flange Lock Nut 712-04065). See Figure 17.

NOTE: Remove the wiring harness from tractor frame (left side only) and mount on the outside of the assembly bracket using the clamp (726-0354) included with your hardware pack.

Undercarriage Assembly

1.Remove the threaded pin, click pins and clevis pins from your undercarriage assembly and retain for installation later. Also, remove the v-belt (754-0371A), this belt will be replaced later with another v-belt

(754-0498) included in this carton. See Figure 18.

2.Remove the flange lock nut and flat washer as pointed out in Figure 19, leaving the spacer under- neath it in place. Mount the idler pulley (756-0627D) and idler bracket (783-1291) from the loose parts included in this carton. Replace the nut and washer.

3.Attach the PTO cable to the idler bracket, then fit the cable into the slotted fitting as seen in Figure 19.

Wiring Harness Clamp

NOTE: Left side view

Hex Screws

Shoulder

Screw

Threaded Pin

Clevis Pins

Flange

Lock

Nuts

Figure 17

V-Belt

Undercarriage Assembly

Figure 18

NOTE: The PTO cable should be hanging down under you tractor after you removed the mowing deck. You will need to slide the undercarriage unit under your trac- tor in position for which it will be mounted. The slanted side should be pointed towards the front of your tractor.

4.Locate v-belt part No. 754-0498 and the extension spring (Part No. 732-04237, which is .50” wide x 12” long) packaged with the loose parts in this carton.

NOTE: The V-belt can be identified by the part number embossed on the outside of the belt.

5.Route the belt around the spindle pulley, inside of the belt keepers and to the inside of the idler pulley. The spring will connect to the Idler bracket but you may install this once the undercarriage is mounted. Otherwise it could fall off or get in the way in the following steps. If you wish to connect this later, retain the spring for later installation. See the Figure 20 illustration on the following page.

PTO Cable

Belt Keeper Pin

Flange Lock

Nut & Washer

Slotted

Idler Pulley &

Fitting

Idler Bracket

 

Figure 19

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents OPERATOR’S Manual Finding and Recording Model Number Customer SupportRider Model Identification FastAttach Snow Thrower Attachment To The OwnerDetermine The Model Your Rider Sample Model NumberTrainingPreparation Your Responsibility Restrict the useYour Responsibility Maintenance & StorageOperation Do not modify engineCarton Contents Contents of Carton Manual PTO Tractors equipped with MountingIdler Pulley and Pin Or 42-inch deck onlyMounting the Belt Keeper AssemblyReversing Idler Assembly Hardware With a 46-inch deck only42, 46, 50, 54 inch Decks With Electric PTO Undercarriage Assembly all tractorsModel Series 600-649 All 800 series Cub Cadet 11C & 13C Upper V-belt 754-0371AUndercarriage Assembly Model Series 600-649 Cub Cadet 11C 38 & 42-inchDeck Size Mounting Undercarriage AssemblyUpper Drive Belt Reference Chart Lift Arm Clevis Pin Model Series 700-799 Bracket Undercarriage AssemblyBracket Assembly PTO Cable Belt Keeper Pin Flange Lock Nut & Washer SlottedRemove Nut Hairpin Clip Mounting the Undercarriage AssemblyPin Attaching Lift Handle Assembling ControlsAttaching the Chute Directional Control Attaching the ReflectorsInset a Inset B Mounting Auger HousingAttaching the Support Tubes Various Models Belt RoutingAll electric PTO Decks 42, 46, 50Left Side Undercarriage Routing the Upper Drive Belt Older Style TractorsRouting the Lower Drive Belt All Tractors Models Spindle Pulley Double-Idler Bracket Right SideQuickly Engaging the Augers ImpellerChute Directional Control Operation Tire Chain Kit NumberLift Adjustment AdjustmentsMaking Adjustments Lower Chute Crank Support Bracket AdjustmentBefore lubricating Repairing, or MaintenanceMaintenance Lubrication Chute Directional ControlPage Snow Thrower 40 B Snow Thrower Attachment 12 8 Belt Guard Page Page MANUFACTURER’S Limited Warranty for
Top Page Image Contents