Yard Machines OEM-190-032 Undercarriage Assembly, Model Series 600-649 Cub Cadet 11C 38 & 42-inch

Page 11

 

Belt Keeper Pin

PTO Cable

Flange Lock

 

Nut & Washer

Slotted

Idler Pulley &

Fitting

Idler Bracket

 

 

Figure 10a

Threaded Pin

V-Belt

 

Click Pins

 

Clevis Pins

 

 

Undercarriage Assembly

 

Figure 10b

Spindle Pulley

Belt Keeper

 

 

Pin

Extension Spring

V-Belt

 

Figure 11

Undercarriage Assembly

1.Remove the v-belt (754-0371A), this belt will be replaced later with another v-belt (754-0498) included in this carton. Also, remove all of the Clevis Pins and Click pins as seen in Figure 10b.

2.Remove the flange lock nut and washer as pointed out in Figure 10a, leaving the spacer underneath it in place. Mount the idler pulley (756-0627D) and idler bracket (783-1291) from the loose parts included in this carton. Replace the flange lock nut and washer.

3.Locate v-belt part No. 754-0498 and the extension spring (Part No. 732-04237, which is .50” wide x 12” long) packaged with the loose parts in this carton. See Figure 11 for reference.

NOTE: The V-belt can be identified by the part number embossed on the outside of the belt.

Route the belt around the spindle pulley, inside of the belt keepers and to the inside of the idler pulley. The spring will connect to the Idler bracket but you may install this once the undercarriage is mounted. Otherwise it could fall off or get in the way in the following steps. If you wish to connect this later, retain the spring for later installation. See the Figure 11.

4.Attach the PTO cable to the idler bracket, then fit the cable into the slotted fitting as seen in Figure 10a.

NOTE: The PTO cable should be hanging down under you tractor after you removed the mowing deck. You will need to slide the undercarriage unit under your trac- tor in position for which it will be mounted. The slanted side should be pointed towards the front of your tractor.

Mounting Undercarriage Assembly

Make certain the correct upper drive belt (754-0498) is installed on the undercarriage assembly. If the appropri- ate belt is not installed, replace it with the correct belt prior to proceeding with mounting the undercarriage.

IMPORTANT: Make certain that the flat side of the belt is facing outward as it sits against both the idler pulley and spindle pulley. This allows the “V” side of the belt to ride snugly in both pulleys.

1.The undercarriage assembly should be in position beneath the tractor, since you already connected the PTO cable in the previous steps.

2.There should already be a threaded pin installed in one of the mounting holes of the undercarriage assembly. If not installed, install it now as in Figure 10b.

Lift the undercarriage assembly up, inserting the weld pins on the assembly up through the aligning holes found along the tractor’s frame rails. Fasten with hairpin clips and flat washers removed earlier. See inset image in Figure 11.

3.Connect the extension spring found in your units loose parts that was mentioned earlier. This spring connects to the idler bracket on the undercarriage assemble and the hole on the rear right-hand snow thrower mounting bracket. See Figure 11.

4.Attach the lower auger drive belt by routing it around and through the pulley system as seen in Figure 11.

NOTE: Proceed to page 16 for next installation steps.

4

Assembly

Model Series

600-649 &

Cub Cadet 11C

(38 & 42-inch

Decks with

Cable-Drive PTO)

Deck Idler/

Pull Style

2005 & Later

WARNING

Before installing attachment, place tractor on a firm and level surface. Place the PTO in

the disengaged

(OFF) position, set the parking brake, shut engine off and remove key to prevent unintended starting.

NOTE: Proper belt routing diagrams can be found on page 18-19 of this manual.

11

Image 11
Contents OPERATOR’S Manual Customer Support Finding and Recording Model NumberSample Model Number FastAttach Snow Thrower Attachment To The OwnerDetermine The Model Your Rider Rider Model IdentificationYour Responsibility Restrict the use TrainingPreparationDo not modify engine Maintenance & StorageOperation Your ResponsibilityCarton Contents Contents of Carton Or 42-inch deck only MountingIdler Pulley and Pin Manual PTO Tractors equipped withWith a 46-inch deck only AssemblyReversing Idler Assembly Hardware Mounting the Belt KeeperUpper V-belt 754-0371A Undercarriage Assembly all tractorsModel Series 600-649 All 800 series Cub Cadet 11C & 13C 42, 46, 50, 54 inch Decks With Electric PTOModel Series 600-649 Cub Cadet 11C 38 & 42-inch Undercarriage AssemblyDeck Size Mounting Undercarriage AssemblyUpper Drive Belt Reference Chart Lift Arm Clevis Pin PTO Cable Belt Keeper Pin Flange Lock Nut & Washer Slotted Bracket Undercarriage AssemblyBracket Assembly Model Series 700-799Remove Nut Hairpin Clip Mounting the Undercarriage AssemblyPin Attaching the Reflectors Assembling ControlsAttaching the Chute Directional Control Attaching Lift HandleInset a Inset B Mounting Auger HousingAttaching the Support Tubes Decks 42, 46, 50 Belt RoutingAll electric PTO Various ModelsSpindle Pulley Double-Idler Bracket Right Side Routing the Upper Drive Belt Older Style TractorsRouting the Lower Drive Belt All Tractors Models Left Side UndercarriageQuickly Engaging the Augers ImpellerChute Directional Control Tire Chain Kit Number OperationLower Chute Crank Support Bracket Adjustment AdjustmentsMaking Adjustments Lift AdjustmentLubrication Chute Directional Control MaintenanceMaintenance Before lubricating Repairing, orPage Snow Thrower 40 B Snow Thrower Attachment 12 8 Belt Guard Page Page MANUFACTURER’S Limited Warranty for