Yard Machines OEM-190-032 warranty Assembling Controls, Attaching the Chute Directional Control

Page 16

6

Assembling

Controls

All Models

NOTE:

All references to left or right side of the

Upper Chute

Crank Rod

Joint Block

Lower Chute

Crank Rod

B

A

Chute Directional

Control Assembly

Figure 24

snow thrower is

from the operating

position only.

Attaching the Chute Directional Control

1.Secure the upper chute crank rod to the joint block

(A)on the lower chute crank rod with the cotter pin

(B)provided. See Figure 24.

2.Attach the chute directional control assembly to the upper lift link on the left side of the auger housing assembly with two hex screws as illustrated in Figure 25. Secure with two flange nuts.

3.Fasten the chute tilt cables to the chute directional control with two of the cable ties provided. Pull the cable ties until they’re snug and trim off excess.

Upper Lift Link

Attaching The

Lift Handle

1.Attach the lift handle to the lift bracket on the right side of the auger housing assembly with the two hex screws and two flange nuts provided. See Figure 26.

2.Fasten the lift cable to the lift handle with two of the cable ties provided. Pull the cable ties until they’re snug and trim off any excess.

Lift Handle

Chute Directional

Control Assembly

Figure 25

Auger Housing Assembly

Figure 26

Attaching the Reﬂectors

Peel off the backing from each of the reflectors to expose the adhesive surface. Adhere the reflectors to the rear of the tractor’s fender (one on the left and one on the right) so that the reflectors simulate taillights.

16

Image 16

Contents OPERATOR’S Manual Finding and Recording Model Number Customer SupportFastAttach Snow Thrower Attachment To The Owner Determine The Model Your RiderRider Model Identiﬁcation Sample Model NumberTrainingPreparation Your Responsibility Restrict the useMaintenance & Storage OperationYour Responsibility Do not modify engineCarton Contents Contents of Carton Mounting Idler Pulley and PinManual PTO Tractors equipped with Or 42-inch deck onlyAssembly Reversing Idler Assembly HardwareMounting the Belt Keeper With a 46-inch deck onlyUndercarriage Assembly all tractors Model Series 600-649 All 800 series Cub Cadet 11C & 13C42, 46, 50, 54 inch Decks With Electric PTO Upper V-belt 754-0371AUndercarriage Assembly Model Series 600-649 Cub Cadet 11C 38 & 42-inchUpper Drive Belt Reference Chart Mounting Undercarriage AssemblyDeck Size Lift Arm Clevis Pin Bracket Undercarriage Assembly Bracket AssemblyModel Series 700-799 PTO Cable Belt Keeper Pin Flange Lock Nut & Washer SlottedPin Mounting the Undercarriage AssemblyRemove Nut Hairpin Clip Assembling Controls Attaching the Chute Directional ControlAttaching Lift Handle Attaching the ReﬂectorsAttaching the Support Tubes Mounting Auger HousingInset a Inset B Belt Routing All electric PTOVarious Models Decks 42, 46, 50Routing the Upper Drive Belt Older Style Tractors Routing the Lower Drive Belt All Tractors ModelsLeft Side Undercarriage Spindle Pulley Double-Idler Bracket Right SideChute Directional Control Engaging the Augers ImpellerQuickly Operation Tire Chain Kit NumberAdjustments Making AdjustmentsLift Adjustment Lower Chute Crank Support Bracket AdjustmentMaintenance MaintenanceBefore lubricating Repairing, or Lubrication Chute Directional ControlPage Snow Thrower 40 B Snow Thrower Attachment 12 8 Belt Guard Page Page MANUFACTURER’S Limited Warranty for