Yazoo/Kees ZMKW48192 manual Weak battery, To attach jumper cables, To remove cables, reverse order

Page 32

operation

Weak battery

If your battery is too weak to start the engine, it should be recharged. (See “Battery” in the Maintenance Section.)

If “jumper cables” are used for emergency starting, follow this procedure:

To attach jumper cables

•Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery.

•Connect the other end of the BLACK cable to a good CHASSIS GROUND on the mower with the discharged battery, away from the fuel tank and battery.

To remove cables, reverse order

•Remove BLACK cable first from chassis and then from the fully charged battery.

•Remove RED cable last from both batteries.

8011-642a

Jumper cable connection

IMPORTANT INFORMATION

Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower to start other vehicles.

WARNING!

Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection then around batteries.

English-32

Image 32

Contents Operator Manual Page Contents Page Congratulations GeneralDriving and Transport on Public Roads TowingGood Service Manufacturing NumberSymbols and decals Important InformationRemove key before Safety General OperationNever take passengers Personal Safety Equipment Slope OperationBe extra cautious when driving on slopes Safe Handling of Gasoline General Maintenance Never make adjustments with the engine Transport Roll over Protection system Rops Customer responsibilitiesRops Assembly Components Setup and adjustmentsSetup Seat Install TiresControl Arms Engine OilThrottle Lever Tension Cutting HeightMower Deck Leveling Keep hands, feet and clothing away from rotating tires Motion Control Linkage AdjustmentPark Brake Adjustment Controls Motion Control Levers Tracking Bypass LinkagesRefueling Fuel Shut Off ValveChoke Control Ignition SwitchHour Meter Parking Brake Blade SwitchThrottle Control Mower Deck Cut Height Lift Lever Always use the high position to transportSteering OperationTraining Before Starting Starting the EngineEnsure that no one is near mower when engaging blade switch To remove cables, reverse order Weak batteryTo attach jumper cables Running Operating on hills Mowing Tips Stopping the Engine Moving Manually Maintenance Safety SystemHardware Air filterBlade replacement Hydraulic systemMower blades Checking the BladesCutter Housings Checking the Parking BrakeChecking the Deck belt Checking the pump beltReplacing the Fuel Filter LubricationTire pressure Adjusting the Mower Deck Cutting height adjustmentsLeveling Anti-scalp rollersCleaning and Washing Caster WheelsHydraulic System-Changing Oil and Filters Hydraulic System, Oil LevelDriver’s Seat Lubricating the Cables Throttle and Choke Cables, Lever BearingsShaft Bushings and Linkage Front Wheel MountSteering Control Shafts Mower Deck Height AdjusterDeck belt pulleys Mower Deck Struts Trouble shooting Problem CauseEnglish-49 Storage Winter StorageCONForMITY Certificates Conformity CertificatesUSA requirements CE requirementsTransmission TECHNICAL DataZMKW52212 ZMKH52252 Engine Productivity Overall DimensionsZMKW52212 ZMKH52252 ZMKH61252 ZMKW48172 Engine 5W30 API SF-SJ SAE 30, SAE 40 API SF-SJZMKH61252 ZMKW48172 ZMKW48192 Engine ZMKW48192 Accessories Torque SpecificationsDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-62 English-63 English-64 At Least Once Each Year English-66 Page 539 131257 R02 03/18/08