3M 2250ME-iD, 2273ME-iD manual Path Mapping with GPS, Create Trace Templates

Page 41

Sending iD Data to GPS (Capture-Transmit Mode / Mode 2)

Menu [SK] + Setup [SK] + More>> [SK] + More>> [SK] + Com [SK Toggle] + GIS

Receivers that have marker locating capability (indicated by ‘iD’ in the model number) can be configured to send 3M™ EMS iD Marker data directly to some GPS devices. When a marker is located and read, the information read from the iD marker with feature and attribute data is sent to the GPS device and is stamped with latitude, longitude and date/time data. The data acquired during this logging process can be uploaded to GIS mapping software. For more information and detailed instructions pertaining to specific GPS units, refer to www.3M.com/dynatel GPS instruction sheet.

Path Mapping with GPS

The M-Series cable and pipe locators are compatible with hand-held GPS devices and now have the ability to map the path of under ground target facilities. While measuring the depth to the target, the technician can automatically log the coordinates of the path on the GPS device. These logged points contain the Trace template that can have valuable information regarding the facility (owner, utility, size, etc.) and the method used to find the path (frequency, current, and measured depth).

In order to transmit the path information to a GPS device, the GPS has to have the ability to accept information on one of its com ports at 4800 Baud. Using the manual supplied with the GPS device, configure the com port of the GPS to communicate with the receiver.

If ArcPad™ is the mapping software on the mobile device, download the 3M software application script from the website: www.3M.com/dynatel

With 3M’s ArcPad™ application installed, the receiver will send the path information (locate frequency, depth, current, and trace template information) into the software program as a logged point and can be saved as a .shp file.

Create Trace Templates

The easiest way to create a Trace template is using the Dynatel PC Tools software. (Software available for no charge at www.3M.com/dynatel - 3M™ Dynatel™ M-Series Locator PC Tools).

1.Create a TRACE template.

2.Save and download the template to the receiver.

Up to four Trace Templates can be stored on the Receiver.

Each Trace template is limited to 132 user editable characters.

The trace template appears in table format: two columns with six lines.

The first column is limited to 8 characters and the second column is limited to 14 characters. In addition to the 132 character table, the receiver will send a sequence number, the frequency, the measured depth of the conductor, and the current to the GPS.

78-8130-6151-8-E

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents 3M Dynatel Contents 78-8130-6151-8-E Intended Use Safety InformationAbout This Manual Quick Start Transmitter Battery InstallationAA Alkaline Batteries Twist cap to open battery compartment Receiver Battery InstallationCleaning Transmitter Keypad and Connector Definitions Service and AccessoriesMaximum Transmitter Output Rechargeable BatteryReceiver Key Pad Definitions Main Menu Menu Screens78-8130-6151-8-E Setting the Receiver Clock Configuring The ReceiverSelect Depth Units Selecting a LanguageMenu 6 + MoreSK + Setup SK + + More» SK + Tone Freq SK Menu 6 + MoreSK + Setup SK + + More» SK + Locate Freq SKEnabling/Disabling Frequencies Selecting External Jack Frequencies Tone FrequenciesSelecting Locating Audio Filtering Power Frequency InterferenceDirect Connect Method Buried Cables And PipesTransmitter Connections Dyna-Coupler Method Induction Method Mode + DirNull SK Toggle Mode + Directional Peak DirPk SK ToggleReceiver Modes Directional PeakMode + IndPk SK Toggle Mode + Spl Pk SK ToggleSpecial Peak Inductive Peak IndPkDepth and Current Estimate Expanded ModeActive PowerFrequencies Auxiliary Locating in Directional Peak ModePassive 78-8130-6151-8-E 78-8130-6151-8-E Determining ADP Depth Locating Active Duct Probes SondesPinpointing the Buried Fault Buried Sheath Faults Earth/Return FaultsTransmitter Setup Green Band 3M Electronic Markers 3M EMS iD Markers Model Initial ConfigurationMenu 6 + Setup SK + Marker Type SK Alert Mode 3M Dynatel Models 2250ME-iD and 2273ME-iD onlyLocating 3M EMS Markers Enabling/Disabling Marker TypesDual Marker Locate Single Marker LocateID Marker Depth Marker Depth EstimateDepth of Passive, Non-iD Marker Menu 6 + Data/Templat SK + User Templat SK Creating New Templates78-8130-6151-8-E Editing Templates Writing iD Markers Menu 6 + Write Mode SKModifying Marker Data to be Programmed Reading iD Markers Activation Key GPS OperationSerial Number and Software Version Inputting the GPS Activation KeyCommunicating with the GPS unit Capturing the GPS Coordinates Capture Mode / ModeMenu SK + Setup SK + More SK + More SK + Com SK Toggle Create Trace Templates Path Mapping with GPSMenu6 + Com SK + GIS SK or PDA SK Select Com Port SettingSending Path Information to GPS Device Read History Reviewing Marker HistoryWrite History SK Menu 6 + Data/Templat SK + Read History SKOther Applications Aerial Faults ToningConnection Diagrams Cable Identification Receiver Setup Help Mode3M Dynatel PC Tool Kit Menu 6 + More SK + Help SKSelf Test Of Receiver Product Description And Optional AccessoriesProduct Description Menu 6 + More SK + Self Test SKOptional 3M Dynatel Accessories Package ContentsSpecification Receiver SpecificationsM 40 in Pwr, Wtr Near-Surface 60 cm 24 Ball MarkerExternal DC source Transmitter SpecificationsMax w/external DC source 40%Track and Trace Solutions
Top Page Image Contents