Safety Equipment and Labels, Specifications

Safety Equipment and Labels

ON-OFF

Switch

Cover

				Protector
DH2510					Warning Label
DH2510	CAUTION READ AND	WEAR EYE	THE BLADES	KEEPS HANDS	ON-OFF
	FOLLOW THE	AND HEARING ARE SHARP!		CLEAR OF
	INSTRUCTIONS PROTECTION		HANDLE WITH CUTTER
	IN THE	AT ALL TIMES CARE.		BLADES WHEN	Switch
	OPERATORS	DURING		STARING THE
	MANUAL.	OPERATION.		ENGINE.

Throttle Interlock

Caution Label

IMPORTANT!

Caution, Danger, Warning, and Operation Information Labels: Make sure all information labels are undam- aged and readable. Immediately replace damaged or

missing information labels. New labels are available Throttle Interlock from your local authorized Shindaiwa dealer.

Figure 2

	Protector
CAUTION	READ AND	WEAR EYE	THE BLADES	KEEPS HANDS
	FOLLOW THE	AND HEARING	ARE SHARP!	CLEAR OF
HT2510	INSTRUCTIONS PROTECTION		HANDLE WITH	CUTTER
	IN THE	AT ALL TIMES	CARE.	BLADES WHEN
	OPERATORS	DURING		STARING THE
	MANUAL.	OPERATION.		ENGINE.

Caution Label

Specifications

Model	HT2510-30 / HT2510-40
Engine Model	SHT2510

DH2510-24 / DH2510-30

SDH2510

Engine Type............................................................................................................................... 4-cycle, horizontal			cylinder, air cooled
Engine Bore x Stroke		34mm x 27mm
Engine Displacement		24.5cc
Unit Weight, Less Fuel	HT2510-30: 5.7kg (12.5lb)		DH2510-24: 5.8 kg (12.8 lb)

	HT2510-40: 6.0kg (13.2lb)		DH2510-30: 5.9 kg (13.0 lb)
Unit Dimensions (LxWxH)	HT2510-30: 1100 x 210 x 230mm		DH2510-24: 1100 x 245 x 230mm
	HT2510-40: 1400 x 210 x 230mm		DH2510-30: 1220 x 245 x 230mm
Max. Power	1.1 hp (.83kw)@ 7,500 rpm (min-1)
Fuel/oil ratio	50:1 with *ISO-L-EGD or JASO FC class 2-cycle Mixing Oil
Fuel Tank Capacity		0.55 liter/18.6 oz.
Carburetor	Walbro WYJ, Diaphragm type
Ignition	Fully electronic, program controlled
Spark Plug		NGK CMR5H
Air Cleaner	Non-reversible heavy-duty filter element
Starting Method		Recoil type
Stopping Method	Slide switch, grounding type

Blade Length	........................................................................ HT2510-30: 740mm / HT2510-40: 1055mm
Blade Type	Double-blade cutting action: single-edged blade

DH2510-24: 610mm / DH2510-30: 740mm

Double-blade cutting action: Double-edged blade

Clutch Type	Centrifugal	clutch, dry-type
Gear Type............................................................................................................................................................. Spur		gears
Gear Lubrication	Lithium-based grease
Standard Equipment	Rear handle with integral controls, anti-vibe mountings, front handle with guard,
	spark plug wrench and blade scabbard (cover)
Options	Deflector Shield, Heavy-Duty Blade (30" & 40")
..............................................................................................................**EPA Emission Compliance Period	Category A

**The EPA emission compliance referred to on the emission compliance label located on the engine, indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements.

Category C = 50 hours (Moderate), B = 125 hours (Intermediate) and A = 300 hours (Extended).

*meets or exceeds these specifications and is recommended for all Shindaiwa products.

Specifications are subject to change without notice.