Northern Industrial Tools M1107C owner manual Moving and Towing to Job Site

Page 12

Moving and Towing to Job Site

5. Put tow bar leg

Move the tow bar leg to the “UP” position and lock. (The support leg must

UP

remain in the up position during towing.)

6. Tow to desired	Tow log splitter carefully to desired work site.
location	(See “Before Each Use” section for instructions on selecting an appropriate work site)

Important safety instructions:

Added length. Be aware of the added length of the splitter.

Speed limit. Never tow this log splitter over 45 mph. Faster speeds may result in loss of control.

Rough terrain. Drive slowly and take extra caution when traveling over rough terrain.

On public roads. If towing on a public road, make sure to comply with all local, state, and federal towing requirements. It is the sole responsibility of the purchaser to obtain licensing, trailer lights, safety chains or signage, as needed to comply.

Unattended. Turn off the towing vehicle before leaving the splitter unattended.

Under the influence. Never tow or operate this splitter while under the influence of alcohol, drugs, or medication

7.Lock leg down & Lock tow bar leg in the DOWN position and disconnect from vehicle.

unhitch

NEVER operate log splitter while it is attached to the vehicle.

12

Image 12

Contents M1107C Hazard Signal Word Definitions Table of Contents About Your Log Splitter This equipment to othersAbout Your Log Splitter Safety Label Locations Safety Label Locations Machine Component Identification DescriptionRef Description Initial Unpacking & Set-Up Replace fill cap Rail BeamMoving and Towing to Job Site Moving the log splitterPlace Fuel valve offAttach safety chains TowingRead Attach to hitch Attach log splitter to vehicle hitch BallMoving and Towing to Job Site Before Each Use-Inspection / Maintenance Step One Inspect and maintain log splitter before each useFuel tank / lines Check fuel tank and fuel lines for leaks Hydraulic system Check the hydraulic system carefullyTires Before Each Use Fueling Step Two FuelingBefore Each Use Work Site Selection & Set-Up Step Three Work site selection and log splitter set-upSelect location Combustibles orLock both legs General safety information Splitting OperationVertical Horizontal lockVertical Splitting Start engine Start the engineCorrect Log Orientation Extend wedge Stop wedgeStuck LOG Instructions below to remove the logReturn to horizontal position Storage Periodic Maintenance Troubleshooting Any Questions, Comments, Problems or Parts OrdersProblem Cause SolutionSpecifications Parts Breakdown-Exploded View 1107 REV C PART# Description QTY Summary of Important Safety Information for Operation Safety During Towing Safety Before Use Read/instructSafety During Inspection/Maintenance Personal protective equipmentSafety During Fueling Safety in Work Site SelectionSafety During Use General Safety During Use Safety in Loading, Operating, and UnloadingSafety After use  Loading/UnloadingSummary of Important Safety Information for Operation

M1107C specifications

The Northern Industrial Tools M1107C is a versatile and powerful tool designed to meet the demands of both professional and DIY users. Known for its reliability and efficiency, this tool stands out in the crowded market of industrial-grade equipment.

One of the main features of the M1107C is its robust construction, built to withstand the rigors of heavy use. The housing is made from durable materials, ensuring longevity and resistance to wear and tear. This makes it suitable for both indoor and outdoor applications, whether you're working in a garage, workshop, or on a construction site.

The M1107C is equipped with a high-performance motor that delivers consistent power for various tasks. With an impressive horsepower rating, this tool can handle tough jobs with ease, from drilling to cutting and beyond. The variable speed control feature allows users to adjust the speed according to their specific needs, providing greater flexibility and precision.

Another notable technology integrated into the M1107C is its ergonomic design. The tool is thoughtfully constructed to reduce user fatigue, featuring a comfortable grip and lightweight build. This ergonomic approach is essential for those who spend extended periods using the tool, as it minimizes strain and maximizes productivity.

Safety is a critical aspect of the M1107C, featuring several safety mechanisms to protect the user during operation. The tool comes with a safety lock feature to prevent accidental starts and a protective guard that ensures safe handling during use. These features allow users to operate the tool confidently, knowing that safety risks are mitigated.

In terms of versatility, the Northern Industrial Tools M1107C can be used in a wide range of applications. It is compatible with various attachments and accessories, making it suitable for an array of tasks including cutting, sanding, and polishing. This adaptability enhances its value, providing users with a single tool that can perform multiple functions.

Overall, the Northern Industrial Tools M1107C is a reliable, efficient, and safe tool ideal for those who value performance and versatility. Its combination of powerful technology, user-friendly design, and robust features makes it a worthy investment for both professionals and hobbyists alike. With the M1107C, users can tackle projects with confidence and achieve high-quality results every time.