Northern Industrial Tools M1107C owner manual Periodic Maintenance

Page 26

Periodic Maintenance

In addition to the maintenance performed with each use, periodic maintenance should also be performed according to the following schedule.

WARNING

AWAYS shut off the engine, disconnect the spark plug, and relieve system pressure before cleaning, adjusting, or repairing the splitter. Relieve system pressure by moving Split Control Lever back and forth several times.

IMPORTANT:

If a part needs replacement only use parts that meets the manufacturer’s specifications. Replacement parts that do not meet specifications may result in a safety hazard or poor operation of the log splitter.

1. Engine

As specified in Perform engine maintenance as specified in engine owner’s manual.

maintenance

engine manual

 

 

2. Hydraulic

Annually / 100

Change Hydraulic Oil.

Oil Change

hours

 

 

 

 

 

WARNING: High fluid pressures and temperatures are developed in

 

 

 

hydraulic log splitters. Hydraulic fluid escaping through a pin hole sized

 

 

 

opening can burn or puncture skin, resulting in wounds that could cause

 

 

 

blood poisoning, infection, disability, gangrene, amputation, or death.

 

 

 

Therefore, the following instructions should be heeded at all times when

 

 

 

inspecting or servicing the hydraulic components of the log splitter.

 

 

NEVER check for leaks with your hand. Leaks can be located by holding a

 

 

 

piece of cardboard or wood (at least two feet long) with your hand at one

 

 

 

end and passing the other end over the suspected area (wear eye protection).

 

 

 

Look for discoloration of the cardboard or wood.

 

 

NEVER adjust the pressure of the pump or valve.

 

 

If injured by escaping fluid, no matter how small the wound is, see a doctor

 

 

 

at once. A typical injection injury may be a small wound that does not look

 

 

 

serious. However, severe infection or reaction can result if proper medical

 

 

 

treatment is not administered immediately by a doctor who is familiar with

 

 

 

injection injuries.

 

 

1. Use 10wt AW32, ASLE H-150, or ISO32 oil.

 

 

2. Relieve hydraulic system pressure by moving Split Control Lever back

 

 

 

and forth several times.

 

 

3. Remove hydraulic oil fill cap.

 

 

 

WARNING: NEVER remove the hydraulic oil fill cap when the engine

 

 

 

is running or hot. Hot oil can escape causing severe burns. Allow the log

 

 

 

splitter to cool completely before removing hydraulic oil fill cap.

 

 

4. Remove the suction hose from the hydraulic tank to drain the hydraulic

 

 

 

oil.

 

 

5. Fill to 1” from top of hydraulic tank with cylinder retracted.

 

 

6. Dispose of used oil at an oil recycling center. Used hydraulic oil is

 

 

 

hazardous waste.

3. Spark

As specified in

If the engine is equipped with a spark arrestor muffler, clean and inspect it

arrestor

spark arrestor

regularly (follow manufacturer’s service instructions). Replace if damaged.

muffler

muffler manual

 

 

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents M1107C Hazard Signal Word Definitions Table of Contents About Your Log Splitter About Your Log SplitterThis equipment to others Safety Label Locations Safety Label Locations Ref Description Machine Component IdentificationDescription Initial Unpacking & Set-Up Replace fill cap Rail BeamPlace Moving and Towing to Job SiteMoving the log splitter Fuel valve offRead Attach safety chainsTowing Attach to hitch Attach log splitter to vehicle hitch BallMoving and Towing to Job Site Fuel tank / lines Check fuel tank and fuel lines for leaks Before Each Use-Inspection / MaintenanceStep One Inspect and maintain log splitter before each use Hydraulic system Check the hydraulic system carefullyTires Before Each Use Fueling Step Two FuelingSelect location Before Each Use Work Site Selection & Set-UpStep Three Work site selection and log splitter set-up Combustibles orLock both legs General safety information Splitting OperationVertical Horizontal lockVertical Splitting Start engine Start the engineCorrect Log Orientation Extend wedge Stop wedgeStuck LOG Instructions below to remove the logReturn to horizontal position Storage Periodic Maintenance Problem TroubleshootingAny Questions, Comments, Problems or Parts Orders Cause SolutionSpecifications Parts Breakdown-Exploded View 1107 REV C PART# Description QTY Summary of Important Safety Information for Operation Safety During Inspection/Maintenance Safety During TowingSafety Before Use Read/instruct Personal protective equipmentSafety During Fueling Safety in Work Site SelectionSafety During Use General Safety During Use Safety in Loading, Operating, and UnloadingSafety After use  Loading/UnloadingSummary of Important Safety Information for Operation

M1107C specifications

The Northern Industrial Tools M1107C is a versatile and powerful tool designed to meet the demands of both professional and DIY users. Known for its reliability and efficiency, this tool stands out in the crowded market of industrial-grade equipment.

One of the main features of the M1107C is its robust construction, built to withstand the rigors of heavy use. The housing is made from durable materials, ensuring longevity and resistance to wear and tear. This makes it suitable for both indoor and outdoor applications, whether you're working in a garage, workshop, or on a construction site.

The M1107C is equipped with a high-performance motor that delivers consistent power for various tasks. With an impressive horsepower rating, this tool can handle tough jobs with ease, from drilling to cutting and beyond. The variable speed control feature allows users to adjust the speed according to their specific needs, providing greater flexibility and precision.

Another notable technology integrated into the M1107C is its ergonomic design. The tool is thoughtfully constructed to reduce user fatigue, featuring a comfortable grip and lightweight build. This ergonomic approach is essential for those who spend extended periods using the tool, as it minimizes strain and maximizes productivity.

Safety is a critical aspect of the M1107C, featuring several safety mechanisms to protect the user during operation. The tool comes with a safety lock feature to prevent accidental starts and a protective guard that ensures safe handling during use. These features allow users to operate the tool confidently, knowing that safety risks are mitigated.

In terms of versatility, the Northern Industrial Tools M1107C can be used in a wide range of applications. It is compatible with various attachments and accessories, making it suitable for an array of tasks including cutting, sanding, and polishing. This adaptability enhances its value, providing users with a single tool that can perform multiple functions.

Overall, the Northern Industrial Tools M1107C is a reliable, efficient, and safe tool ideal for those who value performance and versatility. Its combination of powerful technology, user-friendly design, and robust features makes it a worthy investment for both professionals and hobbyists alike. With the M1107C, users can tackle projects with confidence and achieve high-quality results every time.
Top Page Image Contents