Northern Industrial Tools M1107C owner manual Safety During Use General Safety During Use

Page 34

Summary of Important Safety Information for Operation

Block wheels. Always block the wheels to prevent unintended movement of the log splitter.

Carbon monoxide. The running engine gives off carbon monoxide, a poisonous gas that can kill you. You CANNOT smell it, see it, or taste it. ONLY run log splitter OUTDOORS and away from air intakes. NEVER run log splitter inside homes, garages, sheds, or other semi-enclosed spaces. These spaces can trap poisonous gases, EVEN if you run a fan or open windows. If you start to feel sick, dizzy, or weak while using the log splitter, shut off the engine and get to fresh air RIGHT AWAY. See a doctor. You may have carbon monoxide poisoning.

Safety – During Use

General Safety During Use

WARNING: Before starting this log splitter, review the following rules for safe operation. Failure to follow these rules may result in serious injury to the operator or bystanders.

Safety equipment / controls. Always operate the log splitter with all safety equipment in place and in good working order, and all controls properly adjusted for safe operation.

Operating speed. Always operate the log splitter at the manufacturer’s recommended speed. The maximum speed of the engine, pump and wedge are preset within safe limits.

Know how to stop. Be thoroughly familiar with all controls and with the proper use of the equipment. Know how to stop the log splitter and relieve system pressures quickly if needed.

Daylight only. Only use the log splitter in daylight so you can see what you are doing.

Smoking / sparks. Never smoke while operating the log splitter, and never operate near sources of sparks or flames.

Hot muffler. If you are starting a warm engine, stay clear of muffler. It may still be hot enough to burn you.

Unattended. Never leave the machine unattended while the engine is running.

Under the influence. Never operate, or let anyone else operate, the log splitter while under the influence of alcohol, drugs, or medication.

Adjusting / repairing. Always make sure the engine is off before cleaning, repairing or adjusting the splitter, except as recommended by the manufacturer. In addition, disconnect the spark plug and move all control handles back and forth to relieve system pressure before changing or adjusting hydraulic system components such as hoses, tubing, fittings or other components.

Carbon monoxide. The running engine gives off carbon monoxide, a poisonous gas that can kill you. You CANNOT smell it, see it, or taste it. If you start to feel sick, dizzy, or weak while using the log splitter, shut off the engine and get to fresh air RIGHT AWAY. See a doctor. You may have carbon monoxide poisoning.

Other exhaust dangers. Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Avoid inhalation of exhaust.

Safety in Loading, Operating, and Unloading

Square log ends. Logs that are not cut square can slide out while splitting and become a safety hazard or cause excessive force to log splitter components. Use a chainsaw to cut logs square on each end before attempting to split them.

Single log. Never attempt to split more than one log at a time. Pieces of log can unexpectedly be thrown from the machine causing serious injury.

Split along grain. Do not use the log splitter to split logs across the grain. Doing so will damage the log splitter and could also cause pieces of log to be thrown, injuring the operator or bystanders.

Keep hands clear. ALWAYS keep hands and feet away from the endplate, wedge, and partially split logs while loading, operating and unloading the log splitter.

Operator position. ALWAYS operate the log splitter from the manufacturer’s indicated OPERATOR POSITION. Other positions are unsafe because they can increase the risk of injury from crushing, cutting, flying objects, or burns.

Straddling / reaching across. Never straddle, reach across, or step over the beam while the engine is running and the log splitter is in the horizontal position. You could trip, actuate the controls, and get seriously injured.

Second person. Many accidents occur when there is more than one person involved in loading and operating the log splitter. Only one person should operate the controls. If a second person is assisting in loading logs, the operator

34

Image 34
Contents M1107C Hazard Signal Word Definitions Table of Contents This equipment to others About Your Log SplitterAbout Your Log Splitter Safety Label Locations Safety Label Locations Description Machine Component IdentificationRef Description Initial Unpacking & Set-Up Replace fill cap Rail BeamPlace Moving and Towing to Job SiteMoving the log splitter Fuel valve offRead Attach safety chainsTowing Attach to hitch Attach log splitter to vehicle hitch BallMoving and Towing to Job Site Fuel tank / lines Check fuel tank and fuel lines for leaks Before Each Use-Inspection / MaintenanceStep One Inspect and maintain log splitter before each use Hydraulic system Check the hydraulic system carefullyTires Before Each Use Fueling Step Two FuelingSelect location Before Each Use Work Site Selection & Set-UpStep Three Work site selection and log splitter set-up Combustibles orLock both legs General safety information Splitting OperationVertical Horizontal lockVertical Splitting Start engine Start the engineCorrect Log Orientation Extend wedge Stop wedgeStuck LOG Instructions below to remove the logReturn to horizontal position Storage Periodic Maintenance Problem TroubleshootingAny Questions, Comments, Problems or Parts Orders Cause SolutionSpecifications Parts Breakdown-Exploded View 1107 REV C PART# Description QTY Summary of Important Safety Information for Operation Safety During Inspection/Maintenance Safety During TowingSafety Before Use Read/instruct Personal protective equipmentSafety During Fueling Safety in Work Site SelectionSafety During Use General Safety During Use Safety in Loading, Operating, and UnloadingSafety After use  Loading/UnloadingSummary of Important Safety Information for Operation

M1107C specifications

The Northern Industrial Tools M1107C is a versatile and powerful tool designed to meet the demands of both professional and DIY users. Known for its reliability and efficiency, this tool stands out in the crowded market of industrial-grade equipment.

One of the main features of the M1107C is its robust construction, built to withstand the rigors of heavy use. The housing is made from durable materials, ensuring longevity and resistance to wear and tear. This makes it suitable for both indoor and outdoor applications, whether you're working in a garage, workshop, or on a construction site.

The M1107C is equipped with a high-performance motor that delivers consistent power for various tasks. With an impressive horsepower rating, this tool can handle tough jobs with ease, from drilling to cutting and beyond. The variable speed control feature allows users to adjust the speed according to their specific needs, providing greater flexibility and precision.

Another notable technology integrated into the M1107C is its ergonomic design. The tool is thoughtfully constructed to reduce user fatigue, featuring a comfortable grip and lightweight build. This ergonomic approach is essential for those who spend extended periods using the tool, as it minimizes strain and maximizes productivity.

Safety is a critical aspect of the M1107C, featuring several safety mechanisms to protect the user during operation. The tool comes with a safety lock feature to prevent accidental starts and a protective guard that ensures safe handling during use. These features allow users to operate the tool confidently, knowing that safety risks are mitigated.

In terms of versatility, the Northern Industrial Tools M1107C can be used in a wide range of applications. It is compatible with various attachments and accessories, making it suitable for an array of tasks including cutting, sanding, and polishing. This adaptability enhances its value, providing users with a single tool that can perform multiple functions.

Overall, the Northern Industrial Tools M1107C is a reliable, efficient, and safe tool ideal for those who value performance and versatility. Its combination of powerful technology, user-friendly design, and robust features makes it a worthy investment for both professionals and hobbyists alike. With the M1107C, users can tackle projects with confidence and achieve high-quality results every time.