MTD 7304 manual Steering Wheel, PTO Switch, Throttle Handle, Ignition Switch, Brake Pedal, Forward

Page 10

NOTE: References to LEFT and RIGHT indicate that side of the tractor when facing forward while seated in the drivers seat. Reference to FRONT indicates the grille end of the tractor; to REAR, the drawbar end.

A. Steering Wheel

The steering wheel is centered on the dash panel. It is used to change the direction (left or right) of the tractor while driving.

NOTE: This tractor is equipped with hydraulic power steering. With this feature, the cap and spokes of the steering wheel may change position.

B. PTO Switch

Slide Lock

Button

Figure 2

The PTO switch is a double action rocker type switch located to the right of the steering wheel on the dash panel. Slide the lock button rearward and push the top of the PTO switch downward to engage the PTO. Push the bottom of the switch downward to disengage.

C. Throttle Handle

This symbol indicates the fast position.

This symbol indicates the slow position.

The throttle handle is located to the right of the steering wheel on the dash panel. When set in a given position, a uniform engine speed will be maintained. Rotate the handle rearward to increase the engine speed.

D. Ignition Switch

NOTE: To prevent accidental starting and/or battery discharge, remove the key from the ignition switch when the tractor is not in use.

The ignition switch has three positions as follow:

OFF

STOP

ON-PREHEAT

START

Figure 3

OFF - The engine and electrical system is turned off.

ON - The electrical system and glow plugs are energized.

START- The starter motor will turn the engine. Release the key immediately when the engine starts

E. Brake Pedal

Brake Pedal

Symbol

Figure 4

The brake pedal is located at the front of the right floor board. Depress to engage the tractor brakes and neutralize the hydrostatic transmission. Fully depress the brake pedal to activate the safety interlock switch when starting the tractor.

F.Forward/Reverse Pedal

The forward/reverse pedal is a self neutralizing rocker style pedal located along the right floor board.

Forward Reverse

Pedal Pedal

Symbol Symbol

Figure 5

Forward

Slowly press down on the front of the pedal to start moving forward. The forward ground speed of the tractor is directly affected by the distance the front of the pedal is depressed.

Reverse

WARNING: Check behind the tractor to be sure the area is clear of people, pets or obstacles and use a slower speed to maintain control of the tractor when traveling in reverse.

Press down on the rear of the pedal to move in reverse.

G. Seat Adjustment Lever

The seat adjustment lever is located beneath the left side of the seat. This lever is used to adjust the seat forward or backward.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualCalling Service Information Table of ContentsTo the Owner Tractor Model Plate Recording Model and Serial Number InformationRops Information Plate Important Safe Operation Practices General OperationOperating the PTO Slope OperationChildren Do notSafety Frame Rops ServiceFAN Warning Label Located on Each Side of Radiator Safety LabelsStarting AID Located Under Hood PTO Warning Label Located on Rear PTO Shield Battery Warning Label Located Under HoodRoll Over Warning Label Located on RIGHT/REAR Fender Controls and Features Floorboard and Dash Panel Mounted ControlsSeat Adjustment Lever PTO SwitchIgnition Switch Steering WheelDifferential Lock Pedal Hazard Light SwitchHeadlight Switch Parking Brake LeverBattery Indicator Light Parking Brake Indicator LightPTO Indicator Light Tachometer Engine Coolant Temperature LightFuel Fill Cap Fender Mounted Conrtols and FeaturesPTO Reverse Override Switch PTO Selection LeverHand Holds Transmission Hi/Lo Range Shift LeverCup Holder Amber Hazard LightsRollover Protective Structure Rops OperationFolding the Rops NEW Tractor BREAK-IN Procedures Safety Interlock SystemFueling the Tractor Cold Weather Starting Using Jumper Cables to Start the EngineStarting the Engine Stopping the EngineDriving on Slopes Using the FORWARD/REVERSE PedalDriving the Tractor Stopping the TractorUsing the Differential Lock Pedal Using the HI/LO Range Shift LeverLOW Using the PTO Selection Lever Using the Hydraulic Lift LeverEngaging the PTO Hazard Lights Using the PTO Reverse Override SwitchUsing the TOP Link Retainer Hook LightingUsing the Auxiliary Hydraulic Valve if Equipped Using the Three Point HitchUsing the Hitch Plate Using the Auxiliary Hydraulic Control HandleTractor Weighting On Demand Four Wheel DriveAdjusting the Seat Belt AdjustmentsAdjusting the Seat Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODLubrication Table MaintenanceGeneral Information Lubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Maintenance Battery RemovalBattery Storage Hazard Bulb Replacement Head Light Bulb ReplacementTail Light Bulb Replacement Servicing Electrical System Instrument Panel Bulb ReplacementAccessing the Fuse Center Instrument Panel FusesHazard Light Flasher Relay Main FuseChecking TRANSMISSION/HYDRAULIC System OIL Level Changing TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter Change Check Final Reduction Gear Case Oil Check Front Axle OilChanging Front Axle and Final Reduction Gear Case OIL Lubrication of FWD Drive Shaft Maintenance of the Rollover Protective Structure RopsLubrication of Main Drive Shaft Wheel Bolt TorqueTire Maintenance Tractor StorageRemoving the Tractor from Storage Engine Information and Maintenance Daihatsu Emission Control Defects Warranty CoverageFuel Metering System Cleaning the Radiator Screen and Radiator Engine Maintenance Cleaning the EngineChecking Engine OIL Level Adding Engine OIL Changing the Engine OIL and FilterChecking Engine Coolant Level Inspection of Cooling System Hoses Changing the AIR CleanerChanging the Engine Coolant Servicing the Fuel Filter Draining The Fuel Filter CupChanging The Fuel Filter Specifications Hydraulic Lift System Power Take-OffGeneral Dimensions BrakesOptional Equipment and Accessories Description Model NumberCUB Cadet LLC Post Office BOX CLEVELAND, Ohio

7304 specifications

The MTD 7304 is a powerful and efficient lawn mower that is designed for both residential and commercial use. Known for its reliability and performance, the MTD 7304 has become a popular choice among homeowners and landscape professionals alike. This mower is equipped with a range of features and technologies that enhance its functionality, making yard maintenance an easier task.

One of the standout features of the MTD 7304 is its robust engine. Powered by a durable, high-performance engine, this mower ensures consistent power delivery, making it suitable for tackling a variety of grass types and terrains. The engine is engineered for fuel efficiency, which not only helps in reducing operating costs but also minimizes environmental impact.

The cutting deck of the MTD 7304 is another highlight, typically measuring around 30 inches. This size strikes a perfect balance between maneuverability and cutting capacity, allowing users to navigate through narrow spaces while still covering significant areas in a single pass. The mower also incorporates adjustable cutting heights, providing flexibility for different grass lengths and conditions.

Equipped with advanced technology, the MTD 7304 includes an easy-to-use electric start feature. This eliminates the hassle of pull-starting, making the mower accessible to users of all ages. The mower is also designed with a user-friendly control panel, featuring intuitive controls that allow for effortless operation and adjustments while mowing.

Durability is a key characteristic of the MTD 7304, with high-quality construction materials that can withstand the rigors of regular use. The sturdy frame and components contribute to the mower's long lifespan, ensuring that it remains a reliable choice for years to come. Additionally, the mower often features a robust warranty that reflects the manufacturer's confidence in its durability.

Another notable aspect of the MTD 7304 is its ergonomic design. Comfortable handles and adjustable height options provide ease of use, reducing fatigue during extended mowing sessions. The compact design also aids in storage, allowing users to store the mower in smaller spaces without any hassle.

In summary, the MTD 7304 is a versatile mower that combines power, efficiency, and durability. With its advanced features, user-friendly technologies, and ergonomic design, it stands out as a top choice for those seeking effective lawn care solutions. Whether for a residential lawn or commercial landscaping, the MTD 7304 delivers exceptional performance, making it a valuable addition to any outdoor maintenance toolkit.
Top Page Image Contents