MTD 7304 manual Check Front Axle Oil, Check Final Reduction Gear Case Oil

Page 37

CHECKING OIL LEVEL IN FRONT AXLE AND FINAL REDUCTION GEAR CASES.

Check the front axle and final reduction gear case oil levels after every 50 hours of operation. Check the oil level only while the engine is stopped and the tractor is standing on a level surface.

Check Front Axle Oil

The oil fill plug/dipstick is located on the left side of the axle housing. See Figure 47.

OIL FILL PLUG/DIPSTICK

FRONT AXLE

FULL MARK

Figure 47

•Clean the area around the oil fill plug/dipstick to prevent debris from entering the axle housing. See Figure 47.

•Turn the oil fill plug/dipstick counterclockwise to unscrew from the axle housing.

•Withdraw the dipstick and wipe it clean, then reinsert and screw in all the way. Unscrew and withdraw again to read the oil level. Always keep the oil level between the bottom and the full mark of the dipstick (See Figure 47).

•If the oil level is low, add only enough Cub Cadet Gear Lube to bring the level to the full mark on the dipstick. NEVER overfill the axle housing.

•Reinsert the fill plug/dipstick into the axle housing and turn clockwise to fully tighten.

Check Final Reduction Gear Case Oil

Check the oil level at the two final reduction gear case fill plugs.

•Locate the fill plugs approximately midway up on the rear of the right and left gear cases. See Figure 48.

•Remove the fill plugs and check that the oil level is at the bottom edge of the fill port opening.

FILL PLUG

LH FINAL

REDUCTION

GEAR CASE

Figure 48

•If the oil level is low, use a funnel with a flexible spout to add enough Cub Cadet Gear Lube to bring the level up to the bottom of the fill port.

•Reinstall the fill plug in each gear case.

CHANGING FRONT AXLE AND FINAL REDUCTION GEAR CASE OIL

Change the front axle and final reduction gear case oil after every 300 hours of operation. The total dry capacity of both gear cases and the axle housing is approximately 81 oz. (2.5 qts.)

Change the front axle and final reduction gear case as follows:

•Operate the tractor for a short period to warm the oil to the normal operating temperature. Place the tractor on a level surface, engage the parking brake, and stop the tractor engine.

•To prevent debris from entering the front axle housing, clean the area around the oil fill plug/ dipstick and the axle drain plug located at the center front of the axle. Refer to Figure 47 and Figure 49.

FRONT AXLE

 

DRAIN PLUG

 

Figure 49

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyCalling Service Information Table of ContentsTo the Owner Tractor Model Plate Recording Model and Serial Number InformationRops Information Plate General Operation Important Safe Operation PracticesChildren Slope OperationOperating the PTO Do notService Safety Frame RopsFAN Warning Label Located on Each Side of Radiator Safety LabelsStarting AID Located Under Hood PTO Warning Label Located on Rear PTO Shield Battery Warning Label Located Under HoodRoll Over Warning Label Located on RIGHT/REAR Fender Floorboard and Dash Panel Mounted Controls Controls and FeaturesIgnition Switch PTO SwitchSeat Adjustment Lever Steering WheelHeadlight Switch Hazard Light SwitchDifferential Lock Pedal Parking Brake LeverPTO Indicator Light Tachometer Parking Brake Indicator LightBattery Indicator Light Engine Coolant Temperature LightPTO Reverse Override Switch Fender Mounted Conrtols and FeaturesFuel Fill Cap PTO Selection LeverCup Holder Transmission Hi/Lo Range Shift LeverHand Holds Amber Hazard LightsRollover Protective Structure Rops OperationFolding the Rops NEW Tractor BREAK-IN Procedures Safety Interlock SystemFueling the Tractor Starting the Engine Using Jumper Cables to Start the EngineCold Weather Starting Stopping the EngineDriving the Tractor Using the FORWARD/REVERSE PedalDriving on Slopes Stopping the TractorUsing the Differential Lock Pedal Using the HI/LO Range Shift LeverLOW Using the PTO Selection Lever Using the Hydraulic Lift LeverEngaging the PTO Using the TOP Link Retainer Hook Using the PTO Reverse Override SwitchHazard Lights LightingUsing the Hitch Plate Using the Three Point HitchUsing the Auxiliary Hydraulic Valve if Equipped Using the Auxiliary Hydraulic Control HandleOn Demand Four Wheel Drive Tractor WeightingAdjusting the Seat AdjustmentsAdjusting the Seat Belt Three Point Hitch AdjustmentsCheck the TOE-IN AS Follows Adjusting Front Wheel TOE-INAdjusting Hydraulic Lift Feedback ROD Adjusting the BrakesLubrication Table MaintenanceGeneral Information Lubrication and Maintenance Chart Illustration Service Intervals Operation to Lubrication and Maintenance ChartGeneral Battery Information Accessing the Engine CompartmentBattery Maintenance Battery RemovalBattery Storage Hazard Bulb Replacement Head Light Bulb ReplacementTail Light Bulb Replacement Accessing the Fuse Center Instrument Panel Bulb ReplacementServicing Electrical System Instrument Panel FusesHazard Light Flasher Relay Main FuseChecking TRANSMISSION/HYDRAULIC System OIL Level Changing TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter Change Check Final Reduction Gear Case Oil Check Front Axle OilChanging Front Axle and Final Reduction Gear Case OIL Lubrication of Main Drive Shaft Maintenance of the Rollover Protective Structure RopsLubrication of FWD Drive Shaft Wheel Bolt TorqueTractor Storage Tire MaintenanceRemoving the Tractor from Storage Daihatsu Emission Control Defects Warranty Coverage Engine Information and MaintenanceFuel Metering System Cleaning the Radiator Screen and Radiator Engine Maintenance Cleaning the EngineChecking Engine OIL Level Changing the Engine OIL and Filter Adding Engine OILChecking Engine Coolant Level Inspection of Cooling System Hoses Changing the AIR CleanerChanging the Engine Coolant Draining The Fuel Filter Cup Servicing the Fuel FilterChanging The Fuel Filter Specifications General Dimensions Power Take-OffHydraulic Lift System BrakesDescription Model Number Optional Equipment and AccessoriesCLEVELAND, Ohio CUB Cadet LLC Post Office BOX

7304 specifications

The MTD 7304 is a powerful and efficient lawn mower that is designed for both residential and commercial use. Known for its reliability and performance, the MTD 7304 has become a popular choice among homeowners and landscape professionals alike. This mower is equipped with a range of features and technologies that enhance its functionality, making yard maintenance an easier task.

One of the standout features of the MTD 7304 is its robust engine. Powered by a durable, high-performance engine, this mower ensures consistent power delivery, making it suitable for tackling a variety of grass types and terrains. The engine is engineered for fuel efficiency, which not only helps in reducing operating costs but also minimizes environmental impact.

The cutting deck of the MTD 7304 is another highlight, typically measuring around 30 inches. This size strikes a perfect balance between maneuverability and cutting capacity, allowing users to navigate through narrow spaces while still covering significant areas in a single pass. The mower also incorporates adjustable cutting heights, providing flexibility for different grass lengths and conditions.

Equipped with advanced technology, the MTD 7304 includes an easy-to-use electric start feature. This eliminates the hassle of pull-starting, making the mower accessible to users of all ages. The mower is also designed with a user-friendly control panel, featuring intuitive controls that allow for effortless operation and adjustments while mowing.

Durability is a key characteristic of the MTD 7304, with high-quality construction materials that can withstand the rigors of regular use. The sturdy frame and components contribute to the mower's long lifespan, ensuring that it remains a reliable choice for years to come. Additionally, the mower often features a robust warranty that reflects the manufacturer's confidence in its durability.

Another notable aspect of the MTD 7304 is its ergonomic design. Comfortable handles and adjustable height options provide ease of use, reducing fatigue during extended mowing sessions. The compact design also aids in storage, allowing users to store the mower in smaller spaces without any hassle.

In summary, the MTD 7304 is a versatile mower that combines power, efficiency, and durability. With its advanced features, user-friendly technologies, and ergonomic design, it stands out as a top choice for those seeking effective lawn care solutions. Whether for a residential lawn or commercial landscaping, the MTD 7304 delivers exceptional performance, making it a valuable addition to any outdoor maintenance toolkit.
Top Page Image Contents