MTD 7304 manual Operation, Rollover Protective Structure Rops, Folding the Rops

Page 15

SECTION 2: OPERATION

ROLLOVER PROTECTIVE STRUCTURE (ROPS)

This tractor is equipped with a foldable Rollover Protection Structure (ROPS) and seat belts. When used together they are effective in reducing injuries to the operator in the event of an accidental tractor rollover. The safety provided by the ROPS is minimized if the seat belt is not properly adjusted AND buckled. Refer to ADJUSTMENTS for seat belt adjustment.

ROPS

Figure 12

WARNING: Always wear the seat belt when operating the tractor equipped with a ROPS. However, if the ROPS is in the folded position or has been re- moved, the seat belt must not be used.

Use the following guidelines when using a tractor equipped with a ROPS:

•Be aware of overhead clearances in the area of operation. Check for clearance of door (or gate) openings and other overhead objects such as utility lines and tree branches. Overhead objects could catch the ROPS and upset the tractor.

•Do not modify the ROPS by drilling holes for, or welding accessories to the structure.

•Do not use the ROPS to pull objects with the tractor. Use ONLY the tractor drawbar for pulling.

•In the event of an accident, have the ROPS carefully inspected and, if necessary, replaced by your Cub Cadet dealer. Do not attempt to repair the ROPS.

FOLDING THE ROPS

The foldable ROPS feature allows the operator to quickly lower the ROPS to operate in areas where there is low overhead clearance. However, the ROPS should be used in the lowered position only when absolutely necessary. Operate with the ROPS in the ‘up’ position whenever possible.

WARNING: A folded ROPS does not provide rollover protection. When the ROPS is in the folded position, the seat belt must NOT be used.

Reposition the ROPS as follows:

•Slightly loosen the two hex screws on the front of the ROPS to relieve their pressure on the ROPS. See Figure 13.

•Remove the two internal cotter pins, and, while supporting the ROPS, withdraw the clevis pins. See Figure 13. Carefully lower the ROPS.

•Reinstall the clevis pins and cotter pins for storage.

CLEVIS

PIN

INTERNAL

COTTER PIN

HEX

SCREW

CLEVIS

PIN

Figure 13

To raise the ROPS:

•Remove internal cotter pins and clevis pins and lift the ROPS into position.

•Insert the clevis pins and secure with the internal cotter pins.

•Tighten the hex screws against the ROPS.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyTable of Contents Calling Service InformationTo the Owner Recording Model and Serial Number Information Tractor Model PlateRops Information Plate General Operation Important Safe Operation PracticesDo not Slope OperationChildren Operating the PTOService Safety Frame RopsSafety Labels FAN Warning Label Located on Each Side of RadiatorStarting AID Located Under Hood Battery Warning Label Located Under Hood PTO Warning Label Located on Rear PTO ShieldRoll Over Warning Label Located on RIGHT/REAR Fender Floorboard and Dash Panel Mounted Controls Controls and FeaturesSteering Wheel PTO SwitchIgnition Switch Seat Adjustment LeverParking Brake Lever Hazard Light SwitchHeadlight Switch Differential Lock PedalEngine Coolant Temperature Light Parking Brake Indicator LightPTO Indicator Light Tachometer Battery Indicator LightPTO Selection Lever Fender Mounted Conrtols and FeaturesPTO Reverse Override Switch Fuel Fill CapAmber Hazard Lights Transmission Hi/Lo Range Shift LeverCup Holder Hand HoldsOperation Rollover Protective Structure RopsFolding the Rops Safety Interlock System NEW Tractor BREAK-IN ProceduresFueling the Tractor Stopping the Engine Using Jumper Cables to Start the EngineStarting the Engine Cold Weather StartingStopping the Tractor Using the FORWARD/REVERSE PedalDriving the Tractor Driving on SlopesUsing the HI/LO Range Shift Lever Using the Differential Lock PedalLOW Using the Hydraulic Lift Lever Using the PTO Selection LeverEngaging the PTO Lighting Using the PTO Reverse Override SwitchUsing the TOP Link Retainer Hook Hazard LightsUsing the Auxiliary Hydraulic Control Handle Using the Three Point HitchUsing the Hitch Plate Using the Auxiliary Hydraulic Valve if EquippedOn Demand Four Wheel Drive Tractor WeightingThree Point Hitch Adjustments AdjustmentsAdjusting the Seat Adjusting the Seat BeltCheck the TOE-IN AS Follows Adjusting Front Wheel TOE-INAdjusting Hydraulic Lift Feedback ROD Adjusting the BrakesMaintenance Lubrication TableGeneral Information Lubrication and Maintenance Chart Illustration Service Intervals Operation to Lubrication and Maintenance ChartGeneral Battery Information Accessing the Engine CompartmentBattery Removal Battery MaintenanceBattery Storage Head Light Bulb Replacement Hazard Bulb ReplacementTail Light Bulb Replacement Instrument Panel Fuses Instrument Panel Bulb ReplacementAccessing the Fuse Center Servicing Electrical SystemMain Fuse Hazard Light Flasher RelayChecking TRANSMISSION/HYDRAULIC System OIL Level Changing TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter Change Check Front Axle Oil Check Final Reduction Gear Case OilChanging Front Axle and Final Reduction Gear Case OIL Wheel Bolt Torque Maintenance of the Rollover Protective Structure RopsLubrication of Main Drive Shaft Lubrication of FWD Drive ShaftTractor Storage Tire MaintenanceRemoving the Tractor from Storage Daihatsu Emission Control Defects Warranty Coverage Engine Information and MaintenanceFuel Metering System Engine Maintenance Cleaning the Engine Cleaning the Radiator Screen and RadiatorChecking Engine OIL Level Changing the Engine OIL and Filter Adding Engine OILChecking Engine Coolant Level Changing the AIR Cleaner Inspection of Cooling System HosesChanging the Engine Coolant Draining The Fuel Filter Cup Servicing the Fuel FilterChanging The Fuel Filter Specifications Brakes Power Take-OffGeneral Dimensions Hydraulic Lift SystemDescription Model Number Optional Equipment and AccessoriesCLEVELAND, Ohio CUB Cadet LLC Post Office BOX

7304 specifications

The MTD 7304 is a powerful and efficient lawn mower that is designed for both residential and commercial use. Known for its reliability and performance, the MTD 7304 has become a popular choice among homeowners and landscape professionals alike. This mower is equipped with a range of features and technologies that enhance its functionality, making yard maintenance an easier task.

One of the standout features of the MTD 7304 is its robust engine. Powered by a durable, high-performance engine, this mower ensures consistent power delivery, making it suitable for tackling a variety of grass types and terrains. The engine is engineered for fuel efficiency, which not only helps in reducing operating costs but also minimizes environmental impact.

The cutting deck of the MTD 7304 is another highlight, typically measuring around 30 inches. This size strikes a perfect balance between maneuverability and cutting capacity, allowing users to navigate through narrow spaces while still covering significant areas in a single pass. The mower also incorporates adjustable cutting heights, providing flexibility for different grass lengths and conditions.

Equipped with advanced technology, the MTD 7304 includes an easy-to-use electric start feature. This eliminates the hassle of pull-starting, making the mower accessible to users of all ages. The mower is also designed with a user-friendly control panel, featuring intuitive controls that allow for effortless operation and adjustments while mowing.

Durability is a key characteristic of the MTD 7304, with high-quality construction materials that can withstand the rigors of regular use. The sturdy frame and components contribute to the mower's long lifespan, ensuring that it remains a reliable choice for years to come. Additionally, the mower often features a robust warranty that reflects the manufacturer's confidence in its durability.

Another notable aspect of the MTD 7304 is its ergonomic design. Comfortable handles and adjustable height options provide ease of use, reducing fatigue during extended mowing sessions. The compact design also aids in storage, allowing users to store the mower in smaller spaces without any hassle.

In summary, the MTD 7304 is a versatile mower that combines power, efficiency, and durability. With its advanced features, user-friendly technologies, and ergonomic design, it stands out as a top choice for those seeking effective lawn care solutions. Whether for a residential lawn or commercial landscaping, the MTD 7304 delivers exceptional performance, making it a valuable addition to any outdoor maintenance toolkit.
Top Page Image Contents