MTD 7304 Main Fuse, Hazard Light Flasher Relay, Checking TRANSMISSION/HYDRAULIC System OIL Level

Page 34

Main Fuse

The main fuse in the tractor wire harness protects the tractor’s entire electrical system. A blown main fuse will prevent battery current from passing though the harness.

To replace the main fuse:

•Raise the tractor hood and remove the right side panel.

•Locate the main fuse under the dash panel, along the tractor’s right frame rail. See Figure 43.

MAIN FUSE

FUSE HOLDER

RT. FRAME

RAIL

WIRE

HARNESS

DASH PANEL

Figure 43

•Pull the fuse from the fuse holder and replace with the same capacity fuse (30 Amp). NEVER use a higher amperage fuse.

•Install the side panel and lower the tractor hood.

Hazard Light Flasher Relay

The flasher relay controls the on/off flashing of the hazard lights. If the hazard lights do not function properly, the flasher relay is probably faulty.

Replace the relay as follows:

•Remove the dash panel insert by removing the two screws. Refer to Figure 41.

•Pull the wire harness from the dash opening. Cut and remove the electrical tape holding the flasher relay to the harness. See Figure 44

•After first noting the position of the two harness leads, disconnect the leads and replace the faulty relay with a new relay.

•Secure the relay to the wire harness with electrical tape.

•Position the wire harness in the dash panel and reinstall the dash panel insert.

FLASHER

RELAY

X

X

TAPE

X

 

X

 

 

WIRE

HARNESS

HARNESS

LEADS

Figure 44

CHECKING TRANSMISSION/HYDRAULIC SYSTEM OIL LEVEL

Check the hydro transmission/hydraulic system oil level after every 50 hours of operation. Check the oil level only while the engine is stopped and the tractor is standing on a level surface.

The oil fill plug/dipstick is located at the rear of the tractor, above the rear PTO shield. See Figure 45.

•Clean the area around the oil fill plug/dipstick to prevent debris from entering the transmission housing. See Figure 45.

•Turn the oil fill plug/dipstick counterclockwise to unscrew from the transmission housing.

•Withdraw the dipstick and wipe it clean, then reinsert and screw in all the way. Unscrew and withdraw again to read the oil level. Always keep the oil level between the add and full marks on the dipstick (See Figure 45).

OIL FILL PLUG/DIPSTICK

PTO SHIELD

Full Mark

F

A

Add Mark

Figure 45

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualCalling Service Information Table of ContentsTo the Owner Tractor Model Plate Recording Model and Serial Number InformationRops Information Plate Important Safe Operation Practices General OperationOperating the PTO Slope OperationChildren Do notSafety Frame Rops ServiceFAN Warning Label Located on Each Side of Radiator Safety LabelsStarting AID Located Under Hood PTO Warning Label Located on Rear PTO Shield Battery Warning Label Located Under HoodRoll Over Warning Label Located on RIGHT/REAR Fender Controls and Features Floorboard and Dash Panel Mounted ControlsSeat Adjustment Lever PTO SwitchIgnition Switch Steering WheelDifferential Lock Pedal Hazard Light SwitchHeadlight Switch Parking Brake LeverBattery Indicator Light Parking Brake Indicator LightPTO Indicator Light Tachometer Engine Coolant Temperature LightFuel Fill Cap Fender Mounted Conrtols and FeaturesPTO Reverse Override Switch PTO Selection LeverHand Holds Transmission Hi/Lo Range Shift LeverCup Holder Amber Hazard LightsRollover Protective Structure Rops OperationFolding the Rops NEW Tractor BREAK-IN Procedures Safety Interlock SystemFueling the Tractor Cold Weather Starting Using Jumper Cables to Start the EngineStarting the Engine Stopping the EngineDriving on Slopes Using the FORWARD/REVERSE PedalDriving the Tractor Stopping the TractorUsing the Differential Lock Pedal Using the HI/LO Range Shift LeverLOW Using the PTO Selection Lever Using the Hydraulic Lift LeverEngaging the PTO Hazard Lights Using the PTO Reverse Override SwitchUsing the TOP Link Retainer Hook LightingUsing the Auxiliary Hydraulic Valve if Equipped Using the Three Point HitchUsing the Hitch Plate Using the Auxiliary Hydraulic Control HandleTractor Weighting On Demand Four Wheel DriveAdjusting the Seat Belt AdjustmentsAdjusting the Seat Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODLubrication Table MaintenanceGeneral Information Lubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Maintenance Battery RemovalBattery Storage Hazard Bulb Replacement Head Light Bulb ReplacementTail Light Bulb Replacement Servicing Electrical System Instrument Panel Bulb ReplacementAccessing the Fuse Center Instrument Panel FusesHazard Light Flasher Relay Main FuseChecking TRANSMISSION/HYDRAULIC System OIL Level Changing TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter Change Check Final Reduction Gear Case Oil Check Front Axle OilChanging Front Axle and Final Reduction Gear Case OIL Lubrication of FWD Drive Shaft Maintenance of the Rollover Protective Structure RopsLubrication of Main Drive Shaft Wheel Bolt TorqueTire Maintenance Tractor StorageRemoving the Tractor from Storage Engine Information and Maintenance Daihatsu Emission Control Defects Warranty CoverageFuel Metering System Cleaning the Radiator Screen and Radiator Engine Maintenance Cleaning the EngineChecking Engine OIL Level Adding Engine OIL Changing the Engine OIL and FilterChecking Engine Coolant Level Inspection of Cooling System Hoses Changing the AIR CleanerChanging the Engine Coolant Servicing the Fuel Filter Draining The Fuel Filter CupChanging The Fuel Filter Specifications Hydraulic Lift System Power Take-OffGeneral Dimensions BrakesOptional Equipment and Accessories Description Model NumberCUB Cadet LLC Post Office BOX CLEVELAND, Ohio

7304 specifications

The MTD 7304 is a powerful and efficient lawn mower that is designed for both residential and commercial use. Known for its reliability and performance, the MTD 7304 has become a popular choice among homeowners and landscape professionals alike. This mower is equipped with a range of features and technologies that enhance its functionality, making yard maintenance an easier task.

One of the standout features of the MTD 7304 is its robust engine. Powered by a durable, high-performance engine, this mower ensures consistent power delivery, making it suitable for tackling a variety of grass types and terrains. The engine is engineered for fuel efficiency, which not only helps in reducing operating costs but also minimizes environmental impact.

The cutting deck of the MTD 7304 is another highlight, typically measuring around 30 inches. This size strikes a perfect balance between maneuverability and cutting capacity, allowing users to navigate through narrow spaces while still covering significant areas in a single pass. The mower also incorporates adjustable cutting heights, providing flexibility for different grass lengths and conditions.

Equipped with advanced technology, the MTD 7304 includes an easy-to-use electric start feature. This eliminates the hassle of pull-starting, making the mower accessible to users of all ages. The mower is also designed with a user-friendly control panel, featuring intuitive controls that allow for effortless operation and adjustments while mowing.

Durability is a key characteristic of the MTD 7304, with high-quality construction materials that can withstand the rigors of regular use. The sturdy frame and components contribute to the mower's long lifespan, ensuring that it remains a reliable choice for years to come. Additionally, the mower often features a robust warranty that reflects the manufacturer's confidence in its durability.

Another notable aspect of the MTD 7304 is its ergonomic design. Comfortable handles and adjustable height options provide ease of use, reducing fatigue during extended mowing sessions. The compact design also aids in storage, allowing users to store the mower in smaller spaces without any hassle.

In summary, the MTD 7304 is a versatile mower that combines power, efficiency, and durability. With its advanced features, user-friendly technologies, and ergonomic design, it stands out as a top choice for those seeking effective lawn care solutions. Whether for a residential lawn or commercial landscaping, the MTD 7304 delivers exceptional performance, making it a valuable addition to any outdoor maintenance toolkit.
Top Page Image Contents