MTD 7304 Instrument Panel, Fuel Gauge, Parking Brake Indicator Light, Battery Indicator Light

Page 12

M. Instrument Panel

3

 

4

 

 

 

5

 

 

6

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

1

Orange

Line 8

9 10

Figure 10

1. Fuel Gauge

The fuel gauge, located on the left side of the instrument panel, monitors the fuel level in the fuel tank. The needle pointing to the right indicates a full tank. The ignition switch must be in the ON position to read the fuel gauge.

6. Parking Brake Indicator Light

The bulb illuminates when the ignition switch is in the ON position and the parking brake is engaged. The light flashes if attempting to start the tractor with the brake not engaged.

7. PTO Indicator Light

2. Tachometer

The tachometer, located on the right side of the instrument panel, shows the engine speed in revolutions per minute (RPM). Optimal operating engine speed is 3500 RPM as indicated by the orange line. When operating PTO driven attach- ments the engine RPM indicator should be at or very near the orange line.

3. Battery Indicator Light

The bulb illuminates in a flashing mode to indicate the battery is being discharged. If this warning lamp comes on during operation, check the charging system for possible causes and/or contact your Cub Cadet dealer.

4. Engine Oil Pressure Light

The bulb illuminates when the ignition switch is in the ON position and should turn off shortly after the engine is started. Illumination of this warning lamp indicates low engine oil pressure. If the bulb comes on while the engine is running, stop the engine immediately and check for possible causes.

5. Engine Coolant Temperature Light

Illumination of this warning lamp indicates the temperature of the engine coolant has risen above the prescribed operating range. If the light comes on while operating the tractor, eliminate all loads and try cooling the engine by running at half throttle (Approx. 1600 to 1800 RPM) for a few minutes. Stop the engine and allow to cool; then check for possible causes (e.g. low coolant level, plugged radiator screen).

The light comes on in a fixed mode whenever the PTO switch is in the ON position, with the following exceptions.

The light will illuminate in a flashing mode if attempting to start the tractor with the PTO switch in the ON position.

The light will change to the flashing mode when the PTO switch is on, but the reverse pedal has been engaged and the reverse override has NOT been engaged

8. Hourmeter

The hourmeter records the hours and tenths of an hour (right most digit) that the tractor has been operated. The hourmeter is activated whenever the ignition switch is in the ON position. Keep a record of the actual hours of tractor operation to ensure all maintenance procedures are completed according to the schedule in this manual.

9. Hazard Light Indicator

The two arrows will flash in conjunction with the amber hazard lights when the hazard light switch is turned on.

10. Glow Plug Indicator Light

Illuminates when the ignition switch is turned to the ON position. The light remains lit for a preset time while the glow plugs heat the precombustion chambers of the diesel engine.

NOTE: By design, some of the instrument panel lights will momentarily remain lit after the ignition switch has been turned to the OFF position.

12

Image 12
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualTable of Contents Calling Service InformationTo the Owner Recording Model and Serial Number Information Tractor Model PlateRops Information Plate Important Safe Operation Practices General OperationSlope Operation ChildrenOperating the PTO Do notSafety Frame Rops ServiceSafety Labels FAN Warning Label Located on Each Side of RadiatorStarting AID Located Under Hood Battery Warning Label Located Under Hood PTO Warning Label Located on Rear PTO ShieldRoll Over Warning Label Located on RIGHT/REAR Fender Controls and Features Floorboard and Dash Panel Mounted ControlsPTO Switch Ignition SwitchSeat Adjustment Lever Steering WheelHazard Light Switch Headlight SwitchDifferential Lock Pedal Parking Brake LeverParking Brake Indicator Light PTO Indicator Light TachometerBattery Indicator Light Engine Coolant Temperature LightFender Mounted Conrtols and Features PTO Reverse Override SwitchFuel Fill Cap PTO Selection LeverTransmission Hi/Lo Range Shift Lever Cup HolderHand Holds Amber Hazard LightsOperation Rollover Protective Structure RopsFolding the Rops Safety Interlock System NEW Tractor BREAK-IN ProceduresFueling the Tractor Using Jumper Cables to Start the Engine Starting the EngineCold Weather Starting Stopping the EngineUsing the FORWARD/REVERSE Pedal Driving the TractorDriving on Slopes Stopping the TractorUsing the HI/LO Range Shift Lever Using the Differential Lock PedalLOW Using the Hydraulic Lift Lever Using the PTO Selection LeverEngaging the PTO Using the PTO Reverse Override Switch Using the TOP Link Retainer HookHazard Lights LightingUsing the Three Point Hitch Using the Hitch PlateUsing the Auxiliary Hydraulic Valve if Equipped Using the Auxiliary Hydraulic Control HandleTractor Weighting On Demand Four Wheel DriveAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODMaintenance Lubrication TableGeneral Information Lubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart Service Intervals Operation toAccessing the Engine Compartment General Battery InformationBattery Removal Battery MaintenanceBattery Storage Head Light Bulb Replacement Hazard Bulb ReplacementTail Light Bulb Replacement Instrument Panel Bulb Replacement Accessing the Fuse CenterServicing Electrical System Instrument Panel FusesMain Fuse Hazard Light Flasher RelayChecking TRANSMISSION/HYDRAULIC System OIL Level Changing TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter Change Check Front Axle Oil Check Final Reduction Gear Case OilChanging Front Axle and Final Reduction Gear Case OIL Maintenance of the Rollover Protective Structure Rops Lubrication of Main Drive ShaftLubrication of FWD Drive Shaft Wheel Bolt TorqueTire Maintenance Tractor StorageRemoving the Tractor from Storage Engine Information and Maintenance Daihatsu Emission Control Defects Warranty CoverageFuel Metering System Engine Maintenance Cleaning the Engine Cleaning the Radiator Screen and RadiatorChecking Engine OIL Level Adding Engine OIL Changing the Engine OIL and FilterChecking Engine Coolant Level Changing the AIR Cleaner Inspection of Cooling System HosesChanging the Engine Coolant Servicing the Fuel Filter Draining The Fuel Filter CupChanging The Fuel Filter Specifications Power Take-Off General DimensionsHydraulic Lift System BrakesOptional Equipment and Accessories Description Model NumberCUB Cadet LLC Post Office BOX CLEVELAND, Ohio

7304 specifications

The MTD 7304 is a powerful and efficient lawn mower that is designed for both residential and commercial use. Known for its reliability and performance, the MTD 7304 has become a popular choice among homeowners and landscape professionals alike. This mower is equipped with a range of features and technologies that enhance its functionality, making yard maintenance an easier task.

One of the standout features of the MTD 7304 is its robust engine. Powered by a durable, high-performance engine, this mower ensures consistent power delivery, making it suitable for tackling a variety of grass types and terrains. The engine is engineered for fuel efficiency, which not only helps in reducing operating costs but also minimizes environmental impact.

The cutting deck of the MTD 7304 is another highlight, typically measuring around 30 inches. This size strikes a perfect balance between maneuverability and cutting capacity, allowing users to navigate through narrow spaces while still covering significant areas in a single pass. The mower also incorporates adjustable cutting heights, providing flexibility for different grass lengths and conditions.

Equipped with advanced technology, the MTD 7304 includes an easy-to-use electric start feature. This eliminates the hassle of pull-starting, making the mower accessible to users of all ages. The mower is also designed with a user-friendly control panel, featuring intuitive controls that allow for effortless operation and adjustments while mowing.

Durability is a key characteristic of the MTD 7304, with high-quality construction materials that can withstand the rigors of regular use. The sturdy frame and components contribute to the mower's long lifespan, ensuring that it remains a reliable choice for years to come. Additionally, the mower often features a robust warranty that reflects the manufacturer's confidence in its durability.

Another notable aspect of the MTD 7304 is its ergonomic design. Comfortable handles and adjustable height options provide ease of use, reducing fatigue during extended mowing sessions. The compact design also aids in storage, allowing users to store the mower in smaller spaces without any hassle.

In summary, the MTD 7304 is a versatile mower that combines power, efficiency, and durability. With its advanced features, user-friendly technologies, and ergonomic design, it stands out as a top choice for those seeking effective lawn care solutions. Whether for a residential lawn or commercial landscaping, the MTD 7304 delivers exceptional performance, making it a valuable addition to any outdoor maintenance toolkit.