Multiquip BS46H11 Assembly and installation, Assembly and Installation, Handle Tube Installation

Page 17

assembly and installation

Assembly and Installation

Before the trowel can be put into operation there are some components that must be installed before the trowel can be used.This section provides general instructions on how to install those components. Instruction sheet P/N 20485 provides further details for the handle assembly.

Handle Tube Installation

1.Attach the main handle (tube) to the gearbox as shown in (Figure 4). The mounting hardware should be contained in the shipping container.

MAIN HANDLE

(TUBE)

3/8 FLAT WASHER

3/8-16

NYLOC NUT

3/8-16 X 3.25 HHC SCREW

GEARBOX

Figure 4. Handle Tube Installation

Vibratory T-Handle Bar Placement

1.The vibratory T-handle bar is already attached to the main handle tube.

2.To adjust the height of the T-bar, loosen the star wheel (Figure 5) and position T-handle bar in the desired position.

T-HANDLE BAR

HEIGHT

ADJUSTMENT

STAR WHEEL

Figure 5. T-Handle Bar Adjustment

NOTICE

If additional handle height adjustment is desired, a handle wedge kit can be purchased for your trowel by ordering P/N 2576 from your Multiquip dealer.

These wedges are placed between the handle and the gearbox to adjust the operating height of the handle. This kit comes complete with wedges, new bolts and installation instructions. This will move your operating handle position up or down approximately 3” (76 mm).

Throttle Cable Installation (Engine)

1.Uncoil the throttle cable and housing.

2.Feed the throttle cable through the cable housing.

3.Connect the trowel throttle cable to the engine throttle linkage (Figure 6). There should be a piece of wire installed on the trowel to show where to route the throttle cable.

4.Route cable end through the idle control spring and swivel stop. When connecting the cable housing, make sure that no more than 1/4" (6.4 mm) of the cable housing protrudes past the housing clamp on the engine.

CABLE

END SWIVEL

STOP

ADJUSTER

NUT

IDLE

 

RETURN

SWIVEL

SPRING

STOP HOLE

 

 

CABLE

 

HOUSING

CLAMP

END

SCREW

 

CABLE

 

HOUSING

TROWEL

CLAMP

THROTTLE

 

CABLE

Figure 6. Throttle Cable Installation (Engine)

5.Tighten cable clamp screw and swivel stop screw.

6.After the trowel throttle cable has been connected to the engine throttle linkage, adjust and tighten operator position of the T-bar handle to lock the throttle cable at the proper length.

3. Tighten star wheel firmly.

BS46H SERIES WALK-BEHIND TROWEL • operatION And parts manual — rev. #2 (10/15/13) — page 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model BS46HLE Fuel and chemical exposure Warnings Silicosis Warning Silicosis/Respiratory WarningsWALK-BEHIND Trowel Table of ContentsCompletely Training checklistDaily pre-Operation checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGENEraL SafETy ENgiNE SafETy TrOwEL SafETyOrder Form PT-160 Before servicing equipmentTraNSpOrTiNg SafETy FUeL SaFeTyEmISSIONS INFORmaTION ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmission control Label Label must remain with the engine for its entire lifeSide View Trowel SPECIFICATIONS/DIMENSIONS11997+A12010 in m/s2 ΣA8 Engine SpecificationsGeneral information 15 14 13 12 Trowel ComponentsInitial Servicing Engine ComponentsAssembly and Installation Assembly and installationHandle Tube Installation Vibratory T-Handle Bar PlacementPitch Cable Installation Safety Stop Switch ConnectionShown in Figure Ground pointEngine Oil Check InspectionBefore Starting Belt Check Gearbox OilBelt Guard Check Fuel CheckOperation Inspection/operationLifting the Trowel Onto a Slab Lifting BaleStarting the Engine OperationPlace the engine fuel valve lever in the on position Place the choke lever in the Open positionStarter Grip Testing the Centrifugal Safety Stop SwitchConcrete Finishing Techniques To Begin TrowelingPitching the Blades Standard Handle Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelStopping The Engine Place the safety stop switch in the OFF positionCombo Blades OptionsClip-On Float Blades Optional Float Discs OptionalQuick Pitch Handle Optional Trowel Arm Adjustment Tool OptionalMaintenance Engine check General CleanlinessEngine Air Cleaner Spark Plug Engine oilBelt Never use a spark plug of incorrect heat rangeBlade Pitch Adjustment Procedure Spark arrester cleaningBushings or bent trowel arms Spider removalRemove the trowel arm from the spider plate Changing bladesTrowel arm removal Checking trowel arm straightness Trowel arm Lever adjustmentEnsure the fixture arm is in the up position Shaft and the test surfaceInstalling Pans Onto Finisher Blades ReAssemblyLONG-TERM Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column To 3 Units Suggested Spare PartsNameplate and Decals ISO DECAL, LIFTING/CRUSH, 2.4 X ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, ASK for TRAINING, 2.00 DIA DECAL, Serial PLATE, WBT-CHINAStandard Handle Assy Switch ASSY., Kill Wire ASSY., Kill SwitchSPACER, Slide Block Guide WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option Adjustment PIN NUT , QP Trim Cntl AdjustmentQP Adjustment Block Spring Center BalanceGuard Assy Guard Ring Access PANEL, B FinisherCLIP, Fast Lead SCREW, Fast LeadRequires 26 OZ .8 Liters Gearbox Lubricant for Operation Gearbox AssyFLANGE, Input Shaft SEAL, OILBEARING, CUP, Timken #M11910 GEAR, Worm B Input ShaftEngine and clutch Assy WIRE, Safety Switch CONNECTOR, Splice TAPLifting Bale Assembly B FIN WEIGHT, Automatic Clutch14 1 Spider AssyLock Washer 3/8 MED Blade AssemblyBUSHING, Trowel ARM Spider PlateStabilizer Ring Assy RING, STABILIZER, 16-1/2 ARM 0300B1237 Blade Assy See Notice below 219060201 Guard Ring LUG RingEngine service parts 28462ZE2W11 17620Z4H02028462ZE3W01 17210ZE2822Page Page HERE’S HOW to GET Help
Top Page Image Contents