Multiquip BS46HLE, BS46H90, BS46H11 manual Wiring Diagram

Page 42

WIRING DIAGRAM

P/N 21953

BLK (TOP)	RECOIL
	RECOIL
	STARTER
	COVER

ON		BLK
	O	BLK
	O
	F
	F	(BOTTOM)
		(BOTTOM)

CENTRIFUGAL

MALE

STOP SWITCH

FEMALE

P/N 1488

BLK

BLK

YEL

BLK

MALE

SPLICE TAP

CONNECTOR

YEL

BLK

	OIL LEVEL	OIL ALERT
	SWITCH	OIL ALERT
	SWITCH	UNIT
		UNIT

GRN

OIL LEVEL

INDICATOR

SCREW ENGINE

GROUND

POINT

BLK

BLK

ENGINE
ENGINE		UNIT
STOP		UNIT
STOP
SWITCH

	TRANSISTORIZED
	IGNITION UNIT

CHASSIS

GND.

SPARK

IGNITION PLUG COIL

page 42 — BS46H SERIES WALK-BEHIND TROWEL • operation and parts manUAL — rev. #2 (10/15/13)

Image 42

Contents Model BS46HLE Fuel and chemical exposure Warnings Silicosis/Respiratory Warnings Silicosis WarningTable of Contents WALK-BEHIND TrowelTraining checklist CompletelyDaily pre-operation checklist Daily pre-Operation checklistSafety Information SaFeTy meSSageSGENEraL SafETy Order Form PT-160 TrOwEL SafETyENgiNE SafETy Before servicing equipmentFUeL SaFeTy TraNSpOrTiNg SafETyEmission control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire lifeTrowel SPECIFICATIONS/DIMENSIONS Side ViewEngine Specifications 11997+A12010 in m/s2 ΣA8General information Trowel Components 15 14 13 12Engine Components Initial ServicingHandle Tube Installation Assembly and installationAssembly and Installation Vibratory T-Handle Bar PlacementShown in Figure Safety Stop Switch ConnectionPitch Cable Installation Ground pointInspection Before StartingEngine Oil Check Belt Guard Check Gearbox OilBelt Check Fuel CheckLifting the Trowel Onto a Slab Inspection/operationOperation Lifting BalePlace the engine fuel valve lever in the on position OperationStarting the Engine Place the choke lever in the Open positionTesting the Centrifugal Safety Stop Switch Starter GripPitching the Blades Standard Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelPlace the safety stop switch in the OFF position Stopping The EngineClip-On Float Blades Optional OptionsCombo Blades Float Discs OptionalTrowel Arm Adjustment Tool Optional Quick Pitch Handle OptionalMaintenance General Cleanliness Engine Air CleanerEngine check Belt Engine oilSpark Plug Never use a spark plug of incorrect heat rangeSpark arrester cleaning Blade Pitch Adjustment ProcedureSpider removal Bushings or bent trowel armsChanging blades Trowel arm removalRemove the trowel arm from the spider plate Ensure the fixture arm is in the up position Trowel arm Lever adjustmentChecking trowel arm straightness Shaft and the test surfaceReAssembly Installing Pans Onto Finisher BladesLONG-TERM Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column Suggested Spare Parts To 3 UnitsNameplate and Decals ISO DECAL, ASK for TRAINING, 2.00 DIA ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X DECAL, Serial PLATE, WBT-CHINAStandard Handle Assy SPACER, Slide Block Guide Wire ASSY., Kill SwitchSwitch ASSY., Kill WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option QP Adjustment Block NUT , QP Trim Cntl AdjustmentAdjustment PIN Spring Center BalanceGuard Assy CLIP, Fast Lead Access PANEL, B FinisherGuard Ring SCREW, Fast LeadGearbox Assy Requires 26 OZ .8 Liters Gearbox Lubricant for OperationBEARING, CUP, Timken #M11910 SEAL, OILFLANGE, Input Shaft GEAR, Worm B Input ShaftEngine and clutch Assy Lifting Bale Assembly B FIN CONNECTOR, Splice TAPWIRE, Safety Switch WEIGHT, Automatic ClutchSpider Assy 14 1BUSHING, Trowel ARM Blade AssemblyLock Washer 3/8 MED Spider PlateStabilizer Ring Assy 0300B 1237RING, STABILIZER, 16-1/2 ARM Blade Assy 0201 21906See Notice below Guard Ring LUG RingEngine service parts 28462ZE3W01 17620Z4H02028462ZE2W11 17210ZE2822Page Page HERE’S HOW to GET Help