Multiquip BS46H11, BS46HLE, BS46H90 manual Quick-pitch Handle ASSY. option

Page 50

quick-pitch HANDLE ASSY. (option)

		18
		38	47
		38
		37	36
	35	37	6	7
				7
				34
		39		34
		39
		40
	17	42	41
		42	41
		43
		44	12	31
		44

			45

20

24 28

51

		2
		3
						32
27			22			13
27			22
15			4			33
			4

						14
				19	29	11
						11
		8
		8
48		5	21		26
					26
50	49	30				46
50				25


16		1
16

1023

9

page 50 — BS46H SERIES WALK-BEHIND TROWEL • operation and parts manUAL — rev. #2 (10/15/13)

Image 50

Contents Model BS46HLE Fuel and chemical exposure Warnings Silicosis/Respiratory Warnings Silicosis WarningTable of Contents WALK-BEHIND TrowelTraining checklist CompletelyDaily pre-operation checklist Daily pre-Operation checklistSafety Information SaFeTy meSSageSGENEraL SafETy Order Form PT-160 TrOwEL SafETyENgiNE SafETy Before servicing equipmentFUeL SaFeTy TraNSpOrTiNg SafETyEmission control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire lifeTrowel SPECIFICATIONS/DIMENSIONS Side ViewEngine Specifications 11997+A12010 in m/s2 ΣA8General information Trowel Components 15 14 13 12Engine Components Initial ServicingHandle Tube Installation Assembly and installationAssembly and Installation Vibratory T-Handle Bar PlacementShown in Figure Safety Stop Switch ConnectionPitch Cable Installation Ground pointEngine Oil Check InspectionBefore Starting Belt Guard Check Gearbox OilBelt Check Fuel CheckLifting the Trowel Onto a Slab Inspection/operationOperation Lifting BalePlace the engine fuel valve lever in the on position OperationStarting the Engine Place the choke lever in the Open positionTesting the Centrifugal Safety Stop Switch Starter GripPitching the Blades Standard Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelPlace the safety stop switch in the OFF position Stopping The EngineClip-On Float Blades Optional OptionsCombo Blades Float Discs OptionalTrowel Arm Adjustment Tool Optional Quick Pitch Handle OptionalMaintenance Engine check General CleanlinessEngine Air Cleaner Belt Engine oilSpark Plug Never use a spark plug of incorrect heat rangeSpark arrester cleaning Blade Pitch Adjustment ProcedureSpider removal Bushings or bent trowel armsRemove the trowel arm from the spider plate Changing bladesTrowel arm removal Ensure the fixture arm is in the up position Trowel arm Lever adjustmentChecking trowel arm straightness Shaft and the test surfaceReAssembly Installing Pans Onto Finisher BladesLONG-TERM Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column Suggested Spare Parts To 3 UnitsNameplate and Decals ISO DECAL, ASK for TRAINING, 2.00 DIA ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X DECAL, Serial PLATE, WBT-CHINAStandard Handle Assy SPACER, Slide Block Guide Wire ASSY., Kill SwitchSwitch ASSY., Kill WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option QP Adjustment Block NUT , QP Trim Cntl AdjustmentAdjustment PIN Spring Center BalanceGuard Assy CLIP, Fast Lead Access PANEL, B FinisherGuard Ring SCREW, Fast LeadGearbox Assy Requires 26 OZ .8 Liters Gearbox Lubricant for OperationBEARING, CUP, Timken #M11910 SEAL, OILFLANGE, Input Shaft GEAR, Worm B Input ShaftEngine and clutch Assy Lifting Bale Assembly B FIN CONNECTOR, Splice TAPWIRE, Safety Switch WEIGHT, Automatic ClutchSpider Assy 14 1BUSHING, Trowel ARM Blade AssemblyLock Washer 3/8 MED Spider PlateStabilizer Ring Assy RING, STABILIZER, 16-1/2 ARM 0300B1237 Blade Assy 0201 21906See Notice below Guard Ring LUG RingEngine service parts 28462ZE3W01 17620Z4H02028462ZE2W11 17210ZE2822Page Page HERE’S HOW to GET Help