Multiquip BS46H11, BS46HLE, BS46H90 manual Troubleshooting engine

Page 38

 

troubleshooting

 

 

 

 

 

 

 

Troubleshooting (engine)

 

Symptom

possible problem

Solution

 

 

 

 

Spark plug bridging?

Check gap, insulation or replace spark plug.

 

 

 

 

Carbon deposit on spark plug?

Clean or replace spark plug.

 

 

 

 

Short circuit due to defi cient spark plug

Check spark plug insulation, replace if worn.

 

insulation?

 

 

 

Improper spark plug gap?

Set to proper gap.

 

Fuel reaching carburetor?

Check fuel line.

 

Water in fuel tank?

Flush or replace fuel tank.

 

Fuel fi lter clogged?

Replace fuel fi lter.

Diffi cult to start, fuel is available, but no spark

Stuck carburetor?

Check fl oat mechanism.

Spark plug is red?

Check transistor ignition unit.

at spark plug.

 

 

If insuffi cient compression, repair or replace

 

Spark plug is bluish white?

engine. If injected air leaking, correct leak. If

 

 

carburetor jets clogged, clean carburetor.

 

 

 

 

 

Check transistor ignition unit is broken, and

 

No spark present at tip of spark plug?

replace defective unit. Check if voltage cord

 

cracked or broken and replace. Check if

 

 

 

 

spark plug if fouled and replace.

 

 

 

 

No oil?

Add oil as required.

 

 

 

 

Oil pressure alarm lamp blinks upon starting?

Check automatic shutdown circuit, "oil

 

(if applicable)

sensor". (if applicable)

 

ON/OFF switch is shorted?

Check switch wiring, replace switch.

Diffi cult to start, fuel is available, and spark is

Ignition coil defective?

Replace ignition coil.

Improper spark gap, points dirty?

Set correct spark gap and clean points.

present at the spark plug.

Condenser insulation worn or short circuiting?

Replace condenser.

 

 

Spark plug wire broken or short circuiting?

Replace defective spark plug wiring.

 

Wrong fuel type?

Flush fuel system, and replace with correct

 

type of fuel.

 

 

Diffi cult to start, fuel is available, spark is

 

 

Water or dust in fuel system?

Flush fuel system.

present and compression is normal.

 

 

Air cleaner dirty?

Clean or replace air cleaner.

 

 

 

 

 

Choke open?

Close choke.

 

 

 

 

Suction/exhaust valve stuck or protruded?

Reseat valves.

 

 

 

Diffi cult to start, fuel is available, spark is

Piston ring and/or cylinder worn?

Replace piston rings and/or piston.

 

 

Cylinder head and/or spark plug not tightened

 

present and compression is low.

Torque cylinder head bolts and spark plug.

 

properly?

 

 

Head gasket and/or spark plug gasket damaged?

Replace head and spark plug gaskets.

 

 

 

 

No fuel in fuel tank?

Fill with correct type of fuel.

 

 

 

 

Fuel cock does not open properly?

Apply lubricant to loosen fuel cock lever,

 

replace if necessary.

No fuel present at carburetor.

 

 

 

Fuel fi lter/lines clogged?

Replace fuel fi lter.

 

 

 

 

 

Fuel tank cap breather hole clogged?

Clean or replace fuel tank cap.

 

 

 

 

Air in fuel line?

Bleed fuel line.

 

 

 

page 38 — BS46H SERIES WALK-BEHIND TROWEL • operation and parts manUAL — rev. #2 (10/15/13)

Image 38
Contents Model BS46HLE Fuel and chemical exposure Warnings Silicosis/Respiratory Warnings Silicosis WarningTable of Contents WALK-BEHIND TrowelTraining checklist CompletelyDaily pre-operation checklist Daily pre-Operation checklistSafety Information SaFeTy meSSageSGENEraL SafETy Order Form PT-160 TrOwEL SafETyENgiNE SafETy Before servicing equipmentFUeL SaFeTy TraNSpOrTiNg SafETyEmission control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire lifeTrowel SPECIFICATIONS/DIMENSIONS Side ViewEngine Specifications 11997+A12010 in m/s2 ΣA8General information Trowel Components 15 14 13 12Engine Components Initial ServicingHandle Tube Installation Assembly and installationAssembly and Installation Vibratory T-Handle Bar PlacementShown in Figure Safety Stop Switch ConnectionPitch Cable Installation Ground pointEngine Oil Check InspectionBefore Starting Belt Guard Check Gearbox OilBelt Check Fuel CheckLifting the Trowel Onto a Slab Inspection/operationOperation Lifting BalePlace the engine fuel valve lever in the on position OperationStarting the Engine Place the choke lever in the Open positionTesting the Centrifugal Safety Stop Switch Starter GripPitching the Blades Standard Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelPlace the safety stop switch in the OFF position Stopping The EngineClip-On Float Blades Optional OptionsCombo Blades Float Discs OptionalTrowel Arm Adjustment Tool Optional Quick Pitch Handle OptionalMaintenance Engine check General CleanlinessEngine Air Cleaner Belt Engine oilSpark Plug Never use a spark plug of incorrect heat rangeSpark arrester cleaning Blade Pitch Adjustment ProcedureSpider removal Bushings or bent trowel armsRemove the trowel arm from the spider plate Changing bladesTrowel arm removal Ensure the fixture arm is in the up position Trowel arm Lever adjustmentChecking trowel arm straightness Shaft and the test surfaceReAssembly Installing Pans Onto Finisher BladesLONG-TERM Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column Suggested Spare Parts To 3 UnitsNameplate and Decals ISO DECAL, ASK for TRAINING, 2.00 DIA ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X DECAL, Serial PLATE, WBT-CHINAStandard Handle Assy SPACER, Slide Block Guide Wire ASSY., Kill SwitchSwitch ASSY., Kill WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option QP Adjustment Block NUT , QP Trim Cntl AdjustmentAdjustment PIN Spring Center BalanceGuard Assy CLIP, Fast Lead Access PANEL, B FinisherGuard Ring SCREW, Fast LeadGearbox Assy Requires 26 OZ .8 Liters Gearbox Lubricant for OperationBEARING, CUP, Timken #M11910 SEAL, OILFLANGE, Input Shaft GEAR, Worm B Input ShaftEngine and clutch Assy Lifting Bale Assembly B FIN CONNECTOR, Splice TAPWIRE, Safety Switch WEIGHT, Automatic ClutchSpider Assy 14 1BUSHING, Trowel ARM Blade AssemblyLock Washer 3/8 MED Spider PlateStabilizer Ring Assy RING, STABILIZER, 16-1/2 ARM 0300B1237 Blade Assy 0201 21906See Notice below Guard Ring LUG RingEngine service parts 28462ZE3W01 17620Z4H02028462ZE2W11 17210ZE2822Page Page HERE’S HOW to GET Help