Multiquip BS46H90, BS46HLE, BS46H11 manual WALK-BEHIND Trowel, Table of Contents

Page 4

Table of Contents

BS46H90/BS46H11/BS46HLE

WALK-BEHIND TROWEL

Fuel And Chemical Exposure Warnings

2

Silicosis/Respiratory Warnings

3

Table Of Contents

4

Training Checklist

5

Daily Pre-Operation Checklist

6

Safety Information

7-11

Trowel Specifications/Dimensions

12

Engine Specifications

13

General Information

14

Trowel Components

15

Engine Components

16

Assembly And Installation

17-18

Inspection

19-20

Inspection/Operation

21

Operation

22-26

Options

27-28

Maintenance

29-37

Troubleshooting

38-41

Wiring Diagram

42

Explanation Of Code In Remarks Column

44

Suggested Spare Parts

45

Component Drawings

Nameplate And Decals

46-47

Standard Handle Assy

48-49

Quick-Pitch Handle Assy. (Option)

50-51

Guard Assy

52-53

Gearbox Assy

54-55

Engine And Clutch Assy

56-57

Spider Assy

58-59

Stabilizer Ring Assy

60-61

Blade Assy

62-63

Engine Service Parts

64-65

CE Certifcate of Conformity

67

NOTICE

Specifications and part numbers are subject to change without notice.

page 4 — BS46H SERIES WALK-BEHIND TROWEL • operation and parts manUAL — rev. #2 (10/15/13)

Image 4
Contents Model BS46HLE Fuel and chemical exposure Warnings Silicosis/Respiratory Warnings Silicosis WarningTable of Contents WALK-BEHIND TrowelTraining checklist CompletelyDaily pre-operation checklist Daily pre-Operation checklistSafety Information SaFeTy meSSageSGENEraL SafETy TrOwEL SafETy ENgiNE SafETyOrder Form PT-160 Before servicing equipmentFUeL SaFeTy TraNSpOrTiNg SafETyENvIRONmeNTaL SaFeTy/DeCOmmISSIONINg EmISSIONS INFORmaTIONEmission control Label Label must remain with the engine for its entire lifeTrowel SPECIFICATIONS/DIMENSIONS Side ViewEngine Specifications 11997+A12010 in m/s2 ΣA8General information Trowel Components 15 14 13 12Engine Components Initial ServicingAssembly and installation Assembly and InstallationHandle Tube Installation Vibratory T-Handle Bar PlacementSafety Stop Switch Connection Pitch Cable InstallationShown in Figure Ground pointBefore Starting InspectionEngine Oil Check Gearbox Oil Belt CheckBelt Guard Check Fuel CheckInspection/operation OperationLifting the Trowel Onto a Slab Lifting BaleOperation Starting the EnginePlace the engine fuel valve lever in the on position Place the choke lever in the Open positionTesting the Centrifugal Safety Stop Switch Starter GripTo Begin Troweling Concrete Finishing TechniquesPitching the Blades Standard Handle Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelPlace the safety stop switch in the OFF position Stopping The EngineOptions Combo BladesClip-On Float Blades Optional Float Discs OptionalTrowel Arm Adjustment Tool Optional Quick Pitch Handle OptionalMaintenance Engine Air Cleaner General CleanlinessEngine check Engine oil Spark PlugBelt Never use a spark plug of incorrect heat rangeSpark arrester cleaning Blade Pitch Adjustment ProcedureSpider removal Bushings or bent trowel armsTrowel arm removal Changing bladesRemove the trowel arm from the spider plate Trowel arm Lever adjustment Checking trowel arm straightnessEnsure the fixture arm is in the up position Shaft and the test surfaceReAssembly Installing Pans Onto Finisher BladesLONG-TERM Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column Suggested Spare Parts To 3 UnitsNameplate and Decals ISO DECAL, Read MANUAL, 2.00 DIA ISO DECAL, LIFTING/CRUSH, 2.4 XISO DECAL, ASK for TRAINING, 2.00 DIA DECAL, Serial PLATE, WBT-CHINAStandard Handle Assy Wire ASSY., Kill Switch Switch ASSY., KillSPACER, Slide Block Guide WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option NUT , QP Trim Cntl Adjustment Adjustment PINQP Adjustment Block Spring Center BalanceGuard Assy Access PANEL, B Finisher Guard RingCLIP, Fast Lead SCREW, Fast LeadGearbox Assy Requires 26 OZ .8 Liters Gearbox Lubricant for OperationSEAL, OIL FLANGE, Input ShaftBEARING, CUP, Timken #M11910 GEAR, Worm B Input ShaftEngine and clutch Assy CONNECTOR, Splice TAP WIRE, Safety SwitchLifting Bale Assembly B FIN WEIGHT, Automatic ClutchSpider Assy 14 1Blade Assembly Lock Washer 3/8 MEDBUSHING, Trowel ARM Spider PlateStabilizer Ring Assy 1237 0300BRING, STABILIZER, 16-1/2 ARM Blade Assy 21906 See Notice below0201 Guard Ring LUG RingEngine service parts 17620Z4H020 28462ZE2W1128462ZE3W01 17210ZE2822Page Page HERE’S HOW to GET Help