Multiquip BS46H90, BS46HLE, BS46H11 manual FUeL SaFeTy, TraNSpOrTiNg SafETy

Page 10

Safety Information

FUeL SaFeTy

daNgEr

„DO NOT add fuel to equipment if it is placed inside truck bed with plastic liner. Possibility exists of explosion or fi re due to static electricity.

FUEL

FUEL

„dO NOT start the engine near spilled fuel or combustible fl uids. Fuel is extremely fl ammable and its vapors can cause an explosion if ignited.

„aLwayS refuel in a well-ventilated area, away from sparks and open fl ames.

„aLwayS use extreme caution when working with flammable liquids.

„dO NOT fi ll the fuel tank while the engine is running or hot.

„dO NOT overfi ll tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system.

„Store fuel in appropriate containers, in well-ventilated areas and away from sparks and fl ames.

„NeveR use fuel as a cleaning agent.

„dO NOT smoke around or near the equipment. Fire or explosion could result from fuel vapors or if fuel is spilled on a hot engine.

TraNSpOrTiNg SafETy

CaUTION

„NeveR allow any person or animal to

stand underneath the equipment while lifting.

NOTICE

„Some walk-behind trowels can be lifted or moved by two people utilizing lifting tubes or other special attachments. Generally, however, they must be lifted using lifting bales and cranes, hoists, or forklifts.

„NeveR transport trowel with fl oat pans attached unless safety catches are used and are specifi cally cleared for such transport by the manufacturer.

„NeveR hoist the trowel more than three feet off the ground with fl oat pans attached.

„Before lifting, make sure that the lifting bales are not damaged.

„Always make sure crane or lifting device has been properly secured to the lifting bales of the equipment.

„aLwayS shutdown engine before transporting.

„NeveR lift the equipment while the engine is running.

„Tighten fuel tank cap securely and close fuel cock to prevent fuel from spilling.

„Use adequate lifting cable (wire or rope) of suffi cient strength.

„dO NOT lift machine to unnecessary heights.

„aLwayS tie down equipment during transport by securing the equipment with rope.

page 10 — BS46H SERIES WALK-BEHIND TROWEL • operation and parts manUAL — rev. #2 (10/15/13)

Image 10
Contents Model BS46HLE Fuel and chemical exposure Warnings Silicosis/Respiratory Warnings Silicosis WarningTable of Contents WALK-BEHIND TrowelTraining checklist CompletelyDaily pre-operation checklist Daily pre-Operation checklistSafety Information SaFeTy meSSageSGENEraL SafETy Order Form PT-160 TrOwEL SafETyENgiNE SafETy Before servicing equipmentFUeL SaFeTy TraNSpOrTiNg SafETyEmission control Label ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Label must remain with the engine for its entire lifeTrowel SPECIFICATIONS/DIMENSIONS Side ViewEngine Specifications 11997+A12010 in m/s2 ΣA8General information Trowel Components 15 14 13 12Engine Components Initial ServicingHandle Tube Installation Assembly and installationAssembly and Installation Vibratory T-Handle Bar PlacementShown in Figure Safety Stop Switch ConnectionPitch Cable Installation Ground pointBefore Starting InspectionEngine Oil Check Belt Guard Check Gearbox OilBelt Check Fuel CheckLifting the Trowel Onto a Slab Inspection/operationOperation Lifting BalePlace the engine fuel valve lever in the on position OperationStarting the Engine Place the choke lever in the Open positionTesting the Centrifugal Safety Stop Switch Starter GripPitching the Blades Standard Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelPlace the safety stop switch in the OFF position Stopping The EngineClip-On Float Blades Optional OptionsCombo Blades Float Discs OptionalTrowel Arm Adjustment Tool Optional Quick Pitch Handle OptionalMaintenance Engine Air Cleaner General CleanlinessEngine check Belt Engine oilSpark Plug Never use a spark plug of incorrect heat rangeSpark arrester cleaning Blade Pitch Adjustment ProcedureSpider removal Bushings or bent trowel armsTrowel arm removal Changing bladesRemove the trowel arm from the spider plate Ensure the fixture arm is in the up position Trowel arm Lever adjustmentChecking trowel arm straightness Shaft and the test surfaceReAssembly Installing Pans Onto Finisher BladesLONG-TERM Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column Suggested Spare Parts To 3 UnitsNameplate and Decals ISO DECAL, ASK for TRAINING, 2.00 DIA ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X DECAL, Serial PLATE, WBT-CHINAStandard Handle Assy SPACER, Slide Block Guide Wire ASSY., Kill SwitchSwitch ASSY., Kill WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option QP Adjustment Block NUT , QP Trim Cntl AdjustmentAdjustment PIN Spring Center BalanceGuard Assy CLIP, Fast Lead Access PANEL, B FinisherGuard Ring SCREW, Fast LeadGearbox Assy Requires 26 OZ .8 Liters Gearbox Lubricant for OperationBEARING, CUP, Timken #M11910 SEAL, OILFLANGE, Input Shaft GEAR, Worm B Input ShaftEngine and clutch Assy Lifting Bale Assembly B FIN CONNECTOR, Splice TAPWIRE, Safety Switch WEIGHT, Automatic ClutchSpider Assy 14 1BUSHING, Trowel ARM Blade AssemblyLock Washer 3/8 MED Spider PlateStabilizer Ring Assy 1237 0300BRING, STABILIZER, 16-1/2 ARM Blade Assy 0201 21906See Notice below Guard Ring LUG RingEngine service parts 28462ZE3W01 17620Z4H02028462ZE2W11 17210ZE2822Page Page HERE’S HOW to GET Help