Multiquip BS46H90 manual SPACER, Slide Block Guide, WASHER, FENDER, 1.5OD X 3/8ID, CABLE, Control

Page 49

STANDARD HANDLE ASSY.

NO.	PART NO.	PART NAME	QTY.	REMARKS
1#	0786	SCREW, BHC 1/4-20 X 3/8 NYL PATCH ,NP	2
2#	0786 A	SPACER, SLIDE BLOCK GUIDE	1
3#	1116	NUT, BRASS JAM 5/16-18	2
4#	1665	SCREW, HHC 3/8-16 X 2	1
5#	3233	WASHER, FENDER, 1.5OD X 3/8ID	4
6#	9154	SCREW, HHC 3/8-16 X 1 3/4	2
7#	10133	NUT, NYLOC 3/8-16	2
8#	20280	BLOCK, PITCH CONTROL	1	INCLUDES ITEMS W/ $
9#	20285	CABLE, CONTROL	1
10#	20287	SLIDE BLOCK, TROWEL CONTROL	1
11#	20439	WHEEL ASSY. , HAND	1
12#	20478	GRIP, HANDLE	2
13#	20514	WIRE ASSY., KILL SWITCH	1
14#	20819	HAND WHEEL ASSY, PITCH CONTROL	1	INCLUDES ITEMS W/ @
15#	20856	SWITCH ASSY., KILL	1
16#	21017	SCREW, HHC 3/8-16 x 3.25 FULL THRD GR5 1
17#%	22732	THROTTLE, BICYCLE FINISHER HANDLES	1
18#%	21172	CABLE, THROTTLE 68”	1
19#%	21173	HOUSING, MAGURA THROTTLE CABLES	1
20#	22055	HANDLE WA, VIBRATION CONTROL	1
21#	22059	ISOLATOR, VIB. 80 DUROMETER SHORE A	3
22#	22095	HANDLE, W/A, STOW FIN VIBE CONTROL	1
23#	22166	COVER,VIBE CONTROL HANDLE PAD	1
24#	22167	SCREW, HHC 3/8-16 X 6.5” GRADE 5	1
25#	22206	CHASSIS, CAST VIBRATION ISOLATOR	1	REPLACES P/N 22056
26#	22100	KIT, VIBE CTRL. HANDLE INSTALLATION	1
27#@	20817	WHEEL, HAND J-B HANDLES	1
28#@	0281	BEARING, THRUST NICE, 607	1
29#@	3615	COLLAR, SET 3/4 ID	1
30#@	0122 c	SCREW, SHS 3/8-16 X 1/2	1
31#@	1478	SHAFT, TROWEL CONTROL	1
32#	21243	THROTTLE KIT	1	INCLUDES ITEMS W/ %
33#@	20282	BEARING, TROWEL CONTROL	1
34#$	A1118	PULLEY, PITCH CABLE HANDLE	1
35#$	20279	PIN, SUPPORT BLOCK 3/8 X 1.59	1
36#$	20275	BLOCK, SUPPORT	1
37	22094	HANDLE ASSY, STD. VIBE CONTROL	1	INCLUDES ITEMS W/ #

BS46H SERIES WALK-BEHIND TROWEL • operatION And parts manual — rev. #2 (10/15/13) — page 49

Image 49

Contents Model BS46HLE Fuel and chemical exposure Warnings Silicosis Warning Silicosis/Respiratory WarningsWALK-BEHIND Trowel Table of ContentsCompletely Training checklistDaily pre-Operation checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGENEraL SafETy ENgiNE SafETy TrOwEL SafETyOrder Form PT-160 Before servicing equipmentTraNSpOrTiNg SafETy FUeL SaFeTyEmISSIONS INFORmaTION ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmission control Label Label must remain with the engine for its entire lifeSide View Trowel SPECIFICATIONS/DIMENSIONS11997+A12010 in m/s2 ΣA8 Engine SpecificationsGeneral information 15 14 13 12 Trowel ComponentsInitial Servicing Engine ComponentsAssembly and Installation Assembly and installationHandle Tube Installation Vibratory T-Handle Bar PlacementPitch Cable Installation Safety Stop Switch ConnectionShown in Figure Ground pointBefore Starting InspectionEngine Oil Check Belt Check Gearbox OilBelt Guard Check Fuel CheckOperation Inspection/operationLifting the Trowel Onto a Slab Lifting BaleStarting the Engine OperationPlace the engine fuel valve lever in the on position Place the choke lever in the Open positionStarter Grip Testing the Centrifugal Safety Stop SwitchConcrete Finishing Techniques To Begin TrowelingPitching the Blades Standard Handle Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelStopping The Engine Place the safety stop switch in the OFF positionCombo Blades OptionsClip-On Float Blades Optional Float Discs OptionalQuick Pitch Handle Optional Trowel Arm Adjustment Tool OptionalMaintenance Engine Air Cleaner General CleanlinessEngine check Spark Plug Engine oilBelt Never use a spark plug of incorrect heat rangeBlade Pitch Adjustment Procedure Spark arrester cleaningBushings or bent trowel arms Spider removalTrowel arm removal Changing bladesRemove the trowel arm from the spider plate Checking trowel arm straightness Trowel arm Lever adjustmentEnsure the fixture arm is in the up position Shaft and the test surfaceInstalling Pans Onto Finisher Blades ReAssemblyLONG-TERM Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column To 3 Units Suggested Spare PartsNameplate and Decals ISO DECAL, LIFTING/CRUSH, 2.4 X ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, ASK for TRAINING, 2.00 DIA DECAL, Serial PLATE, WBT-CHINAStandard Handle Assy Switch ASSY., Kill Wire ASSY., Kill SwitchSPACER, Slide Block Guide WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option Adjustment PIN NUT , QP Trim Cntl AdjustmentQP Adjustment Block Spring Center BalanceGuard Assy Guard Ring Access PANEL, B FinisherCLIP, Fast Lead SCREW, Fast LeadRequires 26 OZ .8 Liters Gearbox Lubricant for Operation Gearbox AssyFLANGE, Input Shaft SEAL, OILBEARING, CUP, Timken #M11910 GEAR, Worm B Input ShaftEngine and clutch Assy WIRE, Safety Switch CONNECTOR, Splice TAPLifting Bale Assembly B FIN WEIGHT, Automatic Clutch14 1 Spider AssyLock Washer 3/8 MED Blade AssemblyBUSHING, Trowel ARM Spider PlateStabilizer Ring Assy 1237 0300BRING, STABILIZER, 16-1/2 ARM Blade Assy See Notice below 219060201 Guard Ring LUG RingEngine service parts 28462ZE2W11 17620Z4H02028462ZE3W01 17210ZE2822Page Page HERE’S HOW to GET Help