Multiquip BS46H90, BS46HLE, BS46H11 manual

Page 43

notes

BS46H SERIES WALK-BEHIND TROWEL • operatION And parts manual — rev. #2 (10/15/13) — page 43

Image 43

Contents Model BS46HLE Fuel and chemical exposure Warnings Silicosis Warning Silicosis/Respiratory WarningsWALK-BEHIND Trowel Table of ContentsCompletely Training checklistDaily pre-Operation checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGENEraL SafETy Before servicing equipment TrOwEL SafETyENgiNE SafETy Order Form PT-160TraNSpOrTiNg SafETy FUeL SaFeTyLabel must remain with the engine for its entire life ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmISSIONS INFORmaTION Emission control LabelSide View Trowel SPECIFICATIONS/DIMENSIONS11997+A12010 in m/s2 ΣA8 Engine SpecificationsGeneral information 15 14 13 12 Trowel ComponentsInitial Servicing Engine ComponentsVibratory T-Handle Bar Placement Assembly and installationAssembly and Installation Handle Tube InstallationGround point Safety Stop Switch ConnectionPitch Cable Installation Shown in FigureBefore Starting InspectionEngine Oil Check Fuel Check Gearbox OilBelt Check Belt Guard CheckLifting Bale Inspection/operationOperation Lifting the Trowel Onto a SlabPlace the choke lever in the Open position OperationStarting the Engine Place the engine fuel valve lever in the on positionStarter Grip Testing the Centrifugal Safety Stop SwitchPitching the Blades Quick Pitch Handle To Begin TrowelingConcrete Finishing Techniques Pitching the Blades Standard HandleManeuvering the Trowel Maneuvering the TrowelStopping The Engine Place the safety stop switch in the OFF positionFloat Discs Optional OptionsCombo Blades Clip-On Float Blades OptionalQuick Pitch Handle Optional Trowel Arm Adjustment Tool OptionalMaintenance Engine Air Cleaner General CleanlinessEngine check Never use a spark plug of incorrect heat range Engine oilSpark Plug BeltBlade Pitch Adjustment Procedure Spark arrester cleaningBushings or bent trowel arms Spider removalTrowel arm removal Changing bladesRemove the trowel arm from the spider plate Shaft and the test surface Trowel arm Lever adjustmentChecking trowel arm straightness Ensure the fixture arm is in the up positionInstalling Pans Onto Finisher Blades ReAssemblyLONG-TERM Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column To 3 Units Suggested Spare PartsNameplate and Decals DECAL, Serial PLATE, WBT-CHINA ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, LIFTING/CRUSH, 2.4 X ISO DECAL, ASK for TRAINING, 2.00 DIAStandard Handle Assy WASHER, FENDER, 1.5OD X 3/8ID Wire ASSY., Kill SwitchSwitch ASSY., Kill SPACER, Slide Block GuideQuick-pitch Handle ASSY. option Spring Center Balance NUT , QP Trim Cntl AdjustmentAdjustment PIN QP Adjustment BlockGuard Assy SCREW, Fast Lead Access PANEL, B FinisherGuard Ring CLIP, Fast LeadRequires 26 OZ .8 Liters Gearbox Lubricant for Operation Gearbox AssyGEAR, Worm B Input Shaft SEAL, OILFLANGE, Input Shaft BEARING, CUP, Timken #M11910Engine and clutch Assy WEIGHT, Automatic Clutch CONNECTOR, Splice TAPWIRE, Safety Switch Lifting Bale Assembly B FIN14 1 Spider AssySpider Plate Blade AssemblyLock Washer 3/8 MED BUSHING, Trowel ARMStabilizer Ring Assy 1237 0300BRING, STABILIZER, 16-1/2 ARM Blade Assy Guard Ring LUG Ring 21906See Notice below 0201Engine service parts 17210ZE2822 17620Z4H02028462ZE2W11 28462ZE3W01Page Page HERE’S HOW to GET Help