Multiquip BS46H11 manual Guard Ring, CLIP, Fast Lead, Access PANEL, B Finisher, SCREW, Fast Lead

Page 53

				GUARD ASSY.

NO.	PART NO.	PART NAME	QTY.	REMARKS
1	21973	GUARD RING	1
2	0205	SCREW, HHC 3/8-16 X 1.0	4
3	1391	SCREW, HHC 5/16-24 X 1-1/2 ZINC	4
4	10024	NUT, NYLOC 1/4-20	2
5	21894	CLIP, FAST LEAD	1
6	21979	ACCESS PANEL, B FINISHER	1
7	26250	SCREW, HHC 1/4 - 20 X 1-3/4	2
8	21893	SCREW, FAST LEAD	1
9	21986	WASHER,FAST LEAD-STAINLESS	1
10	21922	CLAMP, 0.625" ID PIPE	2
11	933241	WASHER, FLAT SAE 5/16 GRD 9YZ	4
12	13351	WASHER, FLAT 3/8 EXT THICK HIGH	4

BS46H SERIES WALK-BEHIND TROWEL • operatION And parts manual — rev. #2 (10/15/13) — page 53

Image 53

Contents Model BS46HLE Fuel and chemical exposure Warnings Silicosis Warning Silicosis/Respiratory WarningsWALK-BEHIND Trowel Table of ContentsCompletely Training checklistDaily pre-Operation checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGENEraL SafETy ENgiNE SafETy TrOwEL SafETyOrder Form PT-160 Before servicing equipmentTraNSpOrTiNg SafETy FUeL SaFeTyEmISSIONS INFORmaTION ENvIRONmeNTaL SaFeTy/DeCOmmISSIONINgEmission control Label Label must remain with the engine for its entire lifeSide View Trowel SPECIFICATIONS/DIMENSIONS11997+A12010 in m/s2 ΣA8 Engine SpecificationsGeneral information 15 14 13 12 Trowel ComponentsInitial Servicing Engine ComponentsAssembly and Installation Assembly and installationHandle Tube Installation Vibratory T-Handle Bar PlacementPitch Cable Installation Safety Stop Switch ConnectionShown in Figure Ground pointEngine Oil Check InspectionBefore Starting Belt Check Gearbox OilBelt Guard Check Fuel CheckOperation Inspection/operationLifting the Trowel Onto a Slab Lifting BaleStarting the Engine OperationPlace the engine fuel valve lever in the on position Place the choke lever in the Open positionStarter Grip Testing the Centrifugal Safety Stop SwitchConcrete Finishing Techniques To Begin TrowelingPitching the Blades Standard Handle Pitching the Blades Quick Pitch HandleManeuvering the Trowel Maneuvering the TrowelStopping The Engine Place the safety stop switch in the OFF positionCombo Blades OptionsClip-On Float Blades Optional Float Discs OptionalQuick Pitch Handle Optional Trowel Arm Adjustment Tool OptionalMaintenance Engine check General CleanlinessEngine Air Cleaner Spark Plug Engine oilBelt Never use a spark plug of incorrect heat rangeBlade Pitch Adjustment Procedure Spark arrester cleaningBushings or bent trowel arms Spider removalRemove the trowel arm from the spider plate Changing bladesTrowel arm removal Checking trowel arm straightness Trowel arm Lever adjustmentEnsure the fixture arm is in the up position Shaft and the test surfaceInstalling Pans Onto Finisher Blades ReAssemblyLONG-TERM Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Or malfunctioning? Or replace switch if necessary Troubleshooting Walk-Behind Trowel Wiring Diagram Page Explanation of Code in Remarks Column To 3 Units Suggested Spare PartsNameplate and Decals ISO DECAL, LIFTING/CRUSH, 2.4 X ISO DECAL, Read MANUAL, 2.00 DIAISO DECAL, ASK for TRAINING, 2.00 DIA DECAL, Serial PLATE, WBT-CHINAStandard Handle Assy Switch ASSY., Kill Wire ASSY., Kill SwitchSPACER, Slide Block Guide WASHER, FENDER, 1.5OD X 3/8IDQuick-pitch Handle ASSY. option Adjustment PIN NUT , QP Trim Cntl AdjustmentQP Adjustment Block Spring Center BalanceGuard Assy Guard Ring Access PANEL, B FinisherCLIP, Fast Lead SCREW, Fast LeadRequires 26 OZ .8 Liters Gearbox Lubricant for Operation Gearbox AssyFLANGE, Input Shaft SEAL, OILBEARING, CUP, Timken #M11910 GEAR, Worm B Input ShaftEngine and clutch Assy WIRE, Safety Switch CONNECTOR, Splice TAPLifting Bale Assembly B FIN WEIGHT, Automatic Clutch14 1 Spider AssyLock Washer 3/8 MED Blade AssemblyBUSHING, Trowel ARM Spider PlateStabilizer Ring Assy RING, STABILIZER, 16-1/2 ARM 0300B1237 Blade Assy See Notice below 219060201 Guard Ring LUG RingEngine service parts 28462ZE2W11 17620Z4H02028462ZE3W01 17210ZE2822Page Page HERE’S HOW to GET Help