GLOBUG 4-SPOT — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS | 4 |
|
DANGER
ELECTRICAL
SHOCK HAZARD
When replacing lamp and to prevent electrical shock, ALWAYS shutdown the generator before replacing lamp. Remember to let lamp cool before removing. Use only recommended type lamp as
listed in parts manual. | DCL416 |
| DANGER |
| ELECTRICAL |
| SHOCK HAZARD |
21 | NEVER touch a live power cord |
or active electrical components | |
with wet hands or while standing | |
in water. The possibility of electrical | |
| shock or even death! exists. |
| DCL410 |
| CAUTION |
| LAMP INFORMATION |
11 | ALWAYS turn lamp OFF |
first, before shutting down | |
generator. |
Once lamp is turned OFF, Allow lamp to cool down before turning back on. It will take about 20 minutes
WARNING
BURN HAZARD
To prevent burns, NEVER touch lamp while lamp is on. Lamp surface gets extremely hot! ALWAYS allow sufficient time for lamp to cool down
before touching.
DCL417
5
12
WARNING
3
before lamp can be turned back on.
DCL409
6 | CAUTION |
When the GloBug is used for | |
| |
| |
| from the generator. |
| DCL402 |
7
8
DANGER
WARNING
When lifting of the GloBug is required, ALWAYS attach a rope or chain to the lift hanger. DO NOT use any other lifting points to lift the GloBug.
| LIFT |
| |
| HANGER |
| |
|
|
| DCL412 |
13 |
|
| |
|
|
| |
DANGER |
|
| |
GlowBug |
|
| |
INFORMATION |
|
| |
To prevent tipping, NEVER use |
| 14 | |
in winds that exceed 22 mph |
| ||
(10 m/sec). |
| ||
NEVER use on an incline of 5 |
| ||
degrees or more. The possibility |
|
| |
of tipping exists. |
|
| |
NEVER use in rain or wet |
|
| |
conditions. The possibility of |
|
| |
electrocution exists. |
|
| |
ALWAYS apply parking brake |
|
| |
to prevent moving. |
|
| |
When moving is required, lower |
|
| |
mast fully. |
|
| |
When raising mast, ALWAYS |
|
| |
deploy outriggers to prevent |
|
| |
tipping. |
|
| |
ALWAYS turn OFF generator |
|
| |
before performing maintenance. |
|
| |
| DCL411 |
|
|
15
DANGER
ELECTRICAL
SHOCK HAZARD
NEVER place the GloBug wheels in standing water. The possibility of electrical shock, even death! Exists.
10
DCL400
| WARNING |
20 | BURN HAZARD |
To prevent burns, NEVER | |
| touch ballast or cover while |
| lamp is on. These surfaces are |
| extremely hot! ALWAYS allow |
| sufficient time for both surfaces |
| to cool down before touching. |
| DCL415 |
WARNING |
To avoid injury, |
you MUST read |
and understand |
operator’s manual |
before using this |
machine. |
This machine to |
be operated by |
qualified |
personnel only. |
Ask for training |
as needed. |
18
MODEL SERIAL NO.
19
CAUTION
TIRE PRESSURE
ALWAYS keep tires inflated to correct pressure. Low or incorrect tire pressure could result in brake malfunction.
Recommended tire pressure:
35.5 PSI
(225 kPa)
DCL407
9
DANGER
ELECTRICAL
SHOCK HAZARD
GROUND
To prevent electrical shock or electrocution, the generator MUST be connected to an earth ground. (See NEC Article 250)
DCL405
WARNING
OUTRIGGER
DEPLOYMENT16
SETTING:
Pull outrigger upward at the tip end and rotate backwards until it locks in place.
STOW
POSITION
DEPLOYEDOUTRIGGERS
RELEASE:
To unlock outrigger, push downward on the
DCL414
BALLAST
BOX
17
| HIGH VOLTAGE | DANGER |
|
| DCL418 |
PAGE 32 — GLOBUG