Multiquip gb43sc manual Globug 4-SPOT Maintenance, Periodic Check and Maintenance

Page 27

GLOBUG 4-SPOT — MAINTENANCE

For a prolonged life cycle an extended quality follow the recommended GloBug 4-Spot service guidelines as referenced in Table 3.

TABLE 3. PERIODIC CHECK AND MAINTENANCE

FIGURE

 

PART

 

CHECK ITEM

SOLUTION

 

 

 

 

 

 

 

 

 

 

 

L1

 

Lamp Base

 

Lamp base loose?

 

Screw in securely.

 

 

 

 

 

 

 

 

 

L2

 

Pin Contact

 

Pin contact loose or disconnected?

Tighten or connect securely.

 

 

 

 

 

 

 

 

 

L3

 

Nut

 

Nut not too loose or not too tight?

Tighten correctly.

 

 

 

 

 

 

 

Lamp

L4

 

Hinge for Lamp Stand

Hinge does not move smoothly?

Apply grease.

 

 

 

 

 

 

 

 

L5

 

Pivot for Lamp Stand

Pivot does not turn smoothly?

Apply grease.

 

 

 

 

 

 

 

 

 

 

 

L6

 

Lamp

 

Lamp burned or broken?

Replace.

 

 

 

 

 

 

 

 

 

 

L7

 

Front Glass

 

Front glass dirty?

 

Wipe off dirt.

 

 

 

 

 

 

 

 

 

L8

 

Reflex Mirror

 

Reflex mirror dirty or broken?

Wipe off dirt or replace.

 

 

 

 

 

 

 

 

 

M1

 

Fold Lever

 

Fold lever does lock and unlock properly?

Repair.

 

 

 

 

 

 

 

 

M2

 

Mast Sliding Surface

Mast sliding surface does not slide smoothly?

Apply grease.

 

 

 

 

 

 

 

 

 

Mast

M3

 

Wire Rope

 

Damaged?

 

Apply grease or replace.

 

 

 

 

 

 

 

 

M4

 

Wire Rope End

 

Is wire end damaged (caulking)?

Replace.

 

 

 

 

 

 

 

 

 

 

 

 

M5

 

Winch

 

Defective winch brake ?

Repair or replace.

 

 

 

 

 

 

 

 

 

M6

 

Safety Stop

 

Safety latch defective?

Repair or replace.

 

 

 

 

 

 

 

 

 

C1

 

Counter-Weight

 

Does not movel smoothly?

Spray grease.

 

 

 

 

 

 

 

 

 

C2

 

Outriggers

 

Does not move smoothly?

Spray grease.

 

 

 

 

 

 

 

 

 

C3

 

T-handle and Wheels

Loose links?

 

Tighten securely.

 

 

 

 

 

 

 

 

 

 

C4

 

Bolt for Handle

 

Loose bolt?

 

Tighten securely.

 

 

 

 

 

 

 

 

 

C5

 

Brake Pedal

 

Linkage not working smoothly?

Check, spray grease

 

 

 

 

 

 

 

 

 

Cart

C5

 

Brake Pedal

 

Notch worn-out?

 

Replace.

 

 

 

 

 

 

 

 

 

 

C6

 

Hanger

 

Loose installation?

 

Fasten securely.

 

 

 

 

 

 

 

 

 

C7

 

Front Wheel Pivot

 

Does not turn smoothly?

Check, apply grease.

 

 

 

 

 

 

 

 

 

C8

 

Tires

 

Tire pressure not 35.5 psi (294 kPa)?

Adjust.

 

 

 

 

 

 

 

 

 

C9

 

Link for Front Shaft

 

Linkage does npt move smoothly?

Spray grease.

 

 

 

 

 

 

 

 

 

C10

 

Brake

 

Does not work properly?

Adjust.

 

 

 

 

 

 

 

 

Electric

E1

 

Power Cable

 

Defective or worn cable?

Replace.

 

 

 

 

 

 

 

 

E2

 

Non-load Voltage

 

Is generator output not 125 VAC?

Adjust or replace generator.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

- Daily Check

- Every 20 Hours

- Every 100 hours

- Every 500 hours

 

GLOBUG 4-SPOT — OPERATION AND PARTS MANUAL — REV. #3 (12/15/08) — PAGE 27

Image 27
Contents Model GB43SC Lighting System Proposition 65WARNING Globug 4-SPOT Operation and Parts Manual REV. #3 12/15/08 Table of Contents Effective January 1st Foryour Safety and the Safety of Others Globug 4-SPOT Safety Message Alert SymbolsGlobug 4-SPOT Safety Message Alert Symbols Globug 4-SPOT Rules for Safe Operation General SafetyGlobug 4-SPOT Rules for Safe Operation Lamp Safety and Care Machine Specifications Globug 4-SPOT Dimensions Globug 4-SPOT General Information Globug 4-SPOT Operation and Parts Manual REV. #3 12/15/08 Major Components Globug 4-SPOT ComponentsCatcher Holds the outrigger in place in the stow position Globug 4-SPOT ComponentsGlobug 4-SPOT Setup GloBug SetupLamp Assembly Raising Lamp Stand Raising the Lamp StandTurning Lights Individually Adjusting Angle of the LightsAdjusting Height of the Lights Turning All Lights In One DirectionApplying Power Globug 4-SPOT OperationShutdown Preparation of Lighting Unit For Storage Globug 4-SPOT StorageStorage Globug 4-SPOT StorageBallast Globug 4-SPOT Maintenance Wiring DiagramGlobug 4-SPOT Operation and Parts Manual REV. #3 12/15/08 C10 Globug 4-SPOT MaintenancePeriodic Check and Maintenance Globug 4-SPOT MaintenanceLamp Troubleshooting Globug 4-SPOT -TROUBLESHOOTING LampsGlobug 4-SPOT -TROUBLESHOOTING Mast Explanation of Code in Remarks Column Sample Parts ListQty Description Globug 4-SPOT Spare PartsNameplate and Decals Globug 4-SPOT Nameplate and DecalsPart Name QTY Remarks Globug 4-SPOT Nameplate and DecalsGlobug 4-SPOT Base Plate Assy Bolt and Washer M10 X Globug 4-SPOT Electrical Assy Lamp Globug 4-SPOT Ballast Assy Screw and Washer M5 X Globug 4-SPOT Main Mast Assy Grommet Globug 4-SPOT Main Mast AssyGlobug 4-SPOT -T-HANDLE Assy Handle Grip Globug 4-SPOT Steering Assy SELF-LOCK NUT M8 Globug 4-SPOT Steering AssyGlobug 4-SPOT Outrigger Assy Bracket OUT,R R Globug 4-SPOT Mast Adapter Assy Part Name Globug 4-SPOT Mast Section Assy Second Mast 52 Globug 4-SPOT Operation and Parts Manual REV. #3 12/15/08 Globug 4-SPOT Operation and Parts Manual REV. #3 12/15/08 Heres HOW to GET Help