Multiquip gb43sc manual Globug 4-SPOT -TROUBLESHOOTING Mast

Page 29

GLOBUG 4-SPOT —TROUBLESHOOTING (MAST)

Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, please take a remedial action following the diagnosis based on the Mast Troubleshooting (Table 5) information shown below.

If the problem cannot be remedied, please leave the unit just as it is and consult or company's service department.

TABLE 5. MAST TROUBLESHOOTING

SYMPTOM

POSSIBLE PROBLEM

SOLUTION

 

 

 

 

Is cable caught in mast?

Set cable free.

 

 

 

 

Is end of wire rope disconnected from

Connect wire rope to winch.

Mast cannot be

winch?

 

 

 

raised.

Does surface of mast not slide smoothly?

Apply grease to sliding surface of mast.

 

 

 

 

 

Is winch handle being turned in the wrong

Operate correctly.

 

direction?

 

Mast keeps coming

Is winch latch defective?

Replace part if not functioning properly.

 

 

down.

Is dram shaft loose?

Tighten dram shaft and check its operation.

 

 

 

 

 

Does surface of mast not slide smoothly?

Apply grease to sliding surface of mast.

 

 

 

The mast cannot be

Is brake disk of winch held tight?

Holding winch handle securely, remove the

latch and lower mast slowly (Repair).

lowered.

 

 

 

 

Is safety stopper not working correctly?

Winch up mast a little and lower mast by

 

putting a load on it (Repair).

 

 

 

 

 

GLOBUG 4-SPOT — OPERATION AND PARTS MANUAL — REV. #3 (12/15/08) — PAGE 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Model GB43SC Lighting System Proposition 65WARNING Globug 4-SPOT Operation and Parts Manual REV. #3 12/15/08 Table of Contents Effective January 1st Foryour Safety and the Safety of Others Globug 4-SPOT Safety Message Alert SymbolsGlobug 4-SPOT Safety Message Alert Symbols Globug 4-SPOT Rules for Safe Operation General SafetyGlobug 4-SPOT Rules for Safe Operation Lamp Safety and Care Machine Specifications Globug 4-SPOT Dimensions Globug 4-SPOT General Information Globug 4-SPOT Operation and Parts Manual REV. #3 12/15/08 Major Components Globug 4-SPOT ComponentsCatcher Holds the outrigger in place in the stow position Globug 4-SPOT ComponentsLamp Assembly Globug 4-SPOT SetupGloBug Setup Raising Lamp Stand Raising the Lamp StandAdjusting Height of the Lights Adjusting Angle of the LightsTurning All Lights In One Direction Turning Lights IndividuallyShutdown Applying PowerGlobug 4-SPOT Operation Preparation of Lighting Unit For Storage Globug 4-SPOT StorageStorage Globug 4-SPOT StorageBallast Globug 4-SPOT Maintenance Wiring DiagramGlobug 4-SPOT Operation and Parts Manual REV. #3 12/15/08 C10 Globug 4-SPOT MaintenancePeriodic Check and Maintenance Globug 4-SPOT MaintenanceLamp Troubleshooting Globug 4-SPOT -TROUBLESHOOTING LampsGlobug 4-SPOT -TROUBLESHOOTING Mast Explanation of Code in Remarks Column Sample Parts ListQty Description Globug 4-SPOT Spare PartsNameplate and Decals Globug 4-SPOT Nameplate and DecalsPart Name QTY Remarks Globug 4-SPOT Nameplate and DecalsGlobug 4-SPOT Base Plate Assy Bolt and Washer M10 X Globug 4-SPOT Electrical Assy Lamp Globug 4-SPOT Ballast Assy Screw and Washer M5 X Globug 4-SPOT Main Mast Assy Grommet Globug 4-SPOT Main Mast AssyGlobug 4-SPOT -T-HANDLE Assy Handle Grip Globug 4-SPOT Steering Assy SELF-LOCK NUT M8 Globug 4-SPOT Steering AssyGlobug 4-SPOT Outrigger Assy Bracket OUT,R R Globug 4-SPOT Mast Adapter Assy Part Name Globug 4-SPOT Mast Section Assy Second Mast 52 Globug 4-SPOT Operation and Parts Manual REV. #3 12/15/08 Globug 4-SPOT Operation and Parts Manual REV. #3 12/15/08 Heres HOW to GET Help
Top Page Image Contents