Multiquip GB114BC manual Globug Lighting System PRE-SETUP/OPERATION, Applying Power, Shutdown

Page 26

GLOBUG LIGHTING SYSTEM — PRE-SETUP/OPERATION

DANGER - HIGH VOLTAGE POWER LINES

When raising mast, ALWAYS be on the lookout for overhead obstructions such as high voltage power lines.The possibility exists of electrocution, even death! if the GloBug comes in contact with high voltage power lines.

Applying Power

1.Make sure the power ON/OFF switch (Figure 14) located near the bottom of the mast is in the OFF position.

Figure 14. Power OFF/ON Switch (OFF Position)

CAUTION - READ GENERATOR MANUAL

Before attempting to operate the generator, READ the entire operation section of the manual. Failure to read manual could cause severe damage to the equipment and bodily harm to the operator.

2.The GloBug has a power requirement of 120 VAC, 60 Hz @ 9.5 amps. Connect the GloBug's AC power cord to the 120 VAC twist-lock receptacle (Figure 15) on the the supplied generator.

Figure 15. 120 VAC Receptacle

3.Start the generator as referenced in the "Start-up Section" of the supplied generator manual.

4.Notice that the balloon envelope will begin to deploy as soon as power is applied by an active generator. This function is not controlled by the power ON/OFF switch.

5.Wait until the balloon is fully deployed before attempting to turn on the lamp. The possibility exists of the balloon getting burned (touching the lamp).

6.If the balloon is fully deployed, place the GloBug's ON/ OFF switch in the ON position.

Figure 16. Power OFF/ON Switch (ON Position)

7.The lamp should now be on. If the lamp is not on, check all connections and repeat steps 1 through 6. If the lamp still does not come on contact the MQ service department.

Shutdown

1.Place the power ON/OFF switch (Figure 17) in the OFF position.

Figure 17. Power OFF/ON Switch (OFF Position)

CAUTION - LAMP COOL DOWN

Allow a sufficient amount of time (15-20 minutes) for the lamp (Figure 18) to cool down before turning off

generator. The possibility exists of the balloon getting burned (touching the lamp).

2.Disconnect the GloBug's AC power cable from the generator.The balloon should begin to deflate.

3.Shutdown generator as referenced in the "Shutdown Section" of the supplied generator manual.

PAGE 26 — GLOBUG LIGHTING SYSTEM — OPERATION & PARTS MANUAL — REV. #3 (03/22/06)

Image 26
Contents Model GB114BC Page Heres HOW to GET Help Table of Contents Direct TOLL-FREE access Globug Lighting System Safety Message Alert Symbols Foryour Safety and the Safety of OthersGlobug Lighting System Safety Message Alert Symbols General Safety Globug Lighting System Rules for Safe OperationMast Safety Globug Lighting System Rules for Safe OperationLamp Safety and Care Maintenance Safety EmergenciesGlobug Lighting System Operation and Safety Decals Machine Safety DecalsGlobug Lighting System Operation and Safety Decals Globug Lighting System Operation and Safety Decals Globug Lighting System Specifications SpecificationsGlobug Lighting System Dimensions Globug Lighting System Floodlight Footcandle Plot Floodlight Footcandle Plot Bal120-StandardGlobug Lighting System Floodlight Footcandle Plot Floodlight Footcandle Plot BAL120R-ReflectorDegree coverage Balloon Envelopes Alarm BuzzerGlobug Lighting System General Information Page Globug Lighting System Components Globug Lighting System Components GloBug Setup Outriggers Deployed PositionGlobug Lighting System PRE-SETUP Positioning the BalloonShutdown Globug Lighting System PRE-SETUP/OPERATIONApplying Power Globug Lighting System Shutdown StorageRemoving the Lamp Globug Lighting System MaintenanceRemoving the Lamp/Balloon Assembly Replacing the Balloon Globug Lighting System MaintenanceInstalling a New Lamp Removing the Lamp Cable Removing the Lamp/Balloon AssemblyRemoval of Winch Check Cable WearCable Release Access Point Pulling-Out the Mast SectionsInstallation of Winch Cable Bypassing Cable Stop LatchInstalling the Lamp Power Cable Installation of WinchInstalling the Hanger Ballast Box RemovalFilter Replacement Balloon/Lamp PlacementGlobug Lighting System Maintenance Wiring Diagram Wiring DiagramGlobug Lighting System Maintenance Globug Lighting System Maintenance Globug Lighting System -TROUBLESHOOTING Lamps Lamp TroubleshootingGlobug Lighting System -TROUBLESHOOTING Mast Mast TroubleshootingItems Found In the Items Number Column Explanation of Code in Remarks ColumnItems Found In the Remarks Column Globug Lighting System Spare Parts Qty DescriptionGlobug Lighting System Nameplate and Decals Globug Lighting System Nameplate and Decals Globug Lighting System -T-HANDLE Assy Handle Grip Globug Lighting System Steering Assy Part Name Globug Lighting System Outrigger Assy Bracket OUT,R R Globug Lighting System Mast Adapter Assy Stand Globug Lighting System Main Mast Assy Screw and Washer Globug Lighting System Mast Section Assy Second Mast Globug Lighting System Baseplate Cover Assy Cover Ballast CP Globug Lighting System Ballast Assy Holder Globug Lighting System FAN BLOWER/LAMP Base Assy Cable 2 Balloon CP Globug Lighting System BALLOON/LAMP Guard Assy Globug Lighting System BALLOON/LAMP Guard Assy Effective October 1, 2002 Terms and Conditions of Sale Parts Page Your Local Dealer is