Land Pride 4400ex manual Introduction, Light Scuff, Scratch, Required Tools and Materials

Page 40

Table of Contents

Section 9: Body Repair

Introduction

Land Pride Gondo bodies are constructed of fiberglass. Scuffs, light scratches and deep gouges are in most situations repairable. Land Pride recommends that you use a professional body shop to restore your vehicle’s body. For your consideration, we have provided below a list of recommended tools, materials and steps suggested for repairing the fiberglass body.

NOTE: Land Pride does not supply the required tools, paint and materials needed to repair the vehicle body. All tools, paint and materials should be purchased locally.

Light Scuff

Required Tools and Materials

(See note above)

•1,000 rpm buffing tool, DeWalt #849

•Meguiars buffing compound #8432

•Meguiars polish #8232 (optional)

•Meguiars maroon cutting pad #W-7006

•Meguiars tan polishing pad #W-9006 (optional)

•Meguiars backing plate #W-64

•Soft clean cotton cloths

Steps to Repair

1.Clean entire area of repair. Clean water is fine for this purpose. Do not use solvent as this will damage the body surface.

2.Install cutting pad #7006 on buffer (maroon pad).

3.Spread compound on area of repair, use about as much as it takes to cover a half-dollar coin, this is a good starting point.

4.Set buffing tool to lowest possible speed on dial, do not buff at a high speed as this will heat and warp material.

5.Buff damage area until surface scuff disappears. A second and third application of compound may be required. Keep buffer moving over surface, this will help keep the surface cool. Clean compound residue off surface after each buffing operation. Do not continue to buff compound until dry, or buff the surface when dry. When all scuff marks have been buffed out the surface may still appear a little dull, if so, proceed to #6.

6.Install polish on surface as in step #3.

7.Spread #8232 polish on surface as in step #3.

8.Polish to a high luster or as required to match surrounding material.

9.Wipe clean with soft clean cloth; any dirt on cloth will mar surface.

Scratch

Required Tools and Materials

(See note to left)

•1,000 rpm buffing tool, DeWalt #849

•Meguiars buffing compound #8432

•Meguiars polish #8232 (optional)

•Meguiars maroon cutting pad #W-7006

•Meguiars tan polishing pad #W-9006 (optional)

•Meguiars backing plate #W-64

•Soft clean cotton cloths

•3M interface sanding pad #05774

•Air Vantage finishing sander with 6-inch hook and loop pad

•3M-P800 sanding film #00970

Steps to Repair

1.Clean entire area of repair. Clean water is fine for this purpose. Do not use solvent as this will damage the body surface.

2.Install interface-sanding pad onto finishing sander. Attach sanding film to Interface pad. (Take care in centering sanding pad and film on sander.)

3.Sand surface using about 45 P.S.I. air pressure at tool inlet, do not sand at a high pad speed, because speed causes the sanding film to load with dust and heats the body surface. Proper sander pad speed is based on cut and travel speed of pad, and downward pressure applied by the operator. To clean sanding pad surface, run sander face at 90 degrees on the edge of a piece of cardboard. This cleaning operation will help keep the sanding film clean and run cooler. Continue to sand surface until original scratch damage is no longer visible. Wipe the surface with a cloth then inspect to be sure the entire original scratch has been fully sanded away (very important).

4.Install cutting pad #7006 on buffer (maroon pad).

5.Spread compound #8432 on area of repair, use about as much as it takes to cover a half-dollar coin, this is a good starting point.

6.Set buffing tool to lowest possible speed on dial, do not buff at a high speed as this will heat and warp material.

7.Buff sanded area until surface scuff disappears.

38

4400EX Heavy Duty Off Road Utility Vehicle 720-051M

6/30/05

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Gondo Table of Contents Using This Manual Safety FirstApplication Land Pride Service Department East North Street Owner AssistanceSerial Number Plate Product SupportSafety Symbol Be Aware of Signal WordsFor Your Protection Before OperatingPractice Safe Maintenance Tire SafetyPrepare for Emergencies Wear Protective EquipmentSafe Operating Procedures Table of Contents Safety Decals 818-543C838-492C 838-629C 838-486C 838-490C 838-628C 838-444C Dealer Service and Inspection List Pre-Delivery CertificateVehicle Information Dealer Test Ride ListDealer Delivery To Customer List Customer Acceptance ListDashboard Switches and Instruments Operator ResponsibilitiesGeneral Operation Pre-Start Check ListFoot Operated Controls Fuel Indicator Hand Operated ControlsDriving Conditions Towing the Gondo Descending Steep HillsTraverse Traveling on Steep Hills Towing Without a TrailerTraveling Tips From the Trail Masters Table of Contents Gondo Accessories Gondo OptionsRear Cargo Box TiresPrepare Vehicle for Maintenance General MaintenanceTorque Values Tire Maintenance Jacking the VehicleShock Absorbers Electrical SystemJump Starting the Battery BatteryPrepare Vehicle to Jump-Start Disconnecting Jumper Cables Connecting Jumper CablesFuel System Engine Maintenance Fuel Filter and Fuel Line MaintenanceFilling the Fuel Tank Emptying the Fuel TankPower Steering Belt High Altitude Carburetor KitAir Filter Maintenance Schedule Precleaner Foam ElementPrecleaner Element 61 mm deep -083-02-S Engine Air FilterSpark Arrester Maintenance Schedule Spark Arrester Maintenance ProcedureReplacement Parts Spark ArresterMaintenance Schedule Engine Oil Maintenance Schedule Engine OilEngine Oil Type and Capacity Engine Oil Level CheckEngine Oil and Filter Change 6mo/100hrsDifferential Maintenance Schedule Differential Oil Type and CapacityDifferential Oil Level Check Differential Oil ChangeTransmission Fluid Brake FluidSteering & Cargo Lift Cylinder Fluid Grease Type LubricationPillow Block Bearing Rotating Bearing SurfacesEngine Preparation for Storage Vehicle Storage PreparationVehicle Removal From Storage Preparation Short term storage 90 days or lessIntroduction Light ScuffScratch Required Tools and MaterialsDeep Gouge Specifications and Capacities 4400EX SeriesSymptoms Probable Causes Suggested Remedies Battery is dead Battery will not charge upBrakes are sticking won’t release Brakes don’t functionEngine overheats Engine runs unevenlyEngine stops running Gear Shift is malfunctioningPark brake doesn’t work Starter cranks slowlySteering does not track correctly Steering play is excessiveVehicle speed does not reach 17 MPH Vehicle looses ground speed withoutTorque Values Chart In-tpi Ft-lbTable of Contents Land Pride Limited Warranty Utility VehicleCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA

4400ex specifications

The Land Pride 4400EX is a versatile and robust implement that is designed for agricultural operations and landscaping tasks. This exceptional piece of equipment stands out for its functionality and durability, making it an ideal choice for both professional landscapers and property owners seeking high-performance tools for ground preparation and maintenance.

One of the most notable features of the Land Pride 4400EX is its heavy-duty construction. Built with a solid frame, it ensures stability and reliability even in the challenging conditions of rugged terrains. The implement is designed to handle various tasks such as grading, leveling, and creating smooth surfaces, establishing it as a go-to choice for diverse applications.

The 4400EX is equipped with advanced technologies that enhance its operational efficiency. The implement utilizes a precision-engineered quick-attach system, allowing users to swap out attachments quickly and without complications. This feature saves valuable time on the job site and increases overall productivity.

Another highlight is its adjustable blade depth, which provides users with the versatility to achieve the desired finish for different projects. Whether users are working in soft soil or hard packed areas, the Land Pride 4400EX can adapt to the task at hand, ensuring a professional-grade result every time.

The implement is also designed with user comfort in mind. It features ergonomic controls that are easy to access, allowing operators to navigate smoothly through tasks without experiencing fatigue. Additionally, the Land Pride 4400EX is compatible with a variety of tractors, making it a flexible addition to any farming or landscaping arsenal.

Maintenance of the 4400EX is straightforward due to its design, which minimizes wear and tear on components. Regular upkeep helps ensure longevity, allowing users to leverage this equipment for years to come.

In conclusion, the Land Pride 4400EX stands out for its exceptional construction, advanced features, and user-friendly design. Its versatility and robust performance make it an invaluable tool for anyone looking to enhance their productivity in agricultural and landscaping tasks. With a focus on reliability and efficiency, the 4400EX continues to be a favored choice among professionals and enthusiasts alike.
Top Page Image Contents