Kunz C60K, H60T, H60B, E60B owner manual Assembly Instructions, You should have, Optional hitches

Page 2

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

READ THE COMPLETE ASSEMBLY INSTRUCTIONS BEFORE STARTING THE ASSEMBLY.

You should have:

-one mower deck assembly

-two caster assemblies

-two rear axle assemblies

-one tongue assembly (Lawn & Garden Hitching or ATV Tongue)

-one tow vehicle hitch assembly (only included on Lawn & Garden Hitching)

Optional hitches:

-one tongue extension

-one rear hitch assembly

A.ASSEMBLY OF MOWER WHEELS

1. Set the mower deck assembly on wood blocks so that it is suspended off the ground.

Left Rear Axle Assy.

Retainer Bolts Optional hitches:

Tongue Pivot Bolt

Left Caster Assy.

Tongue – Attach to Either Left or Right Caster Assy.

Figure 1. Assembly of Wheels, Tongue and Rear Hitch

2.Install the two caster assemblies in the retainers on the front of the mower deck. See figure 1. Before securing the caster supports, determine which side of the mower the tongue will be placed on and install the caster support stop on the tongue side. See Figure 2. Secure with 3/8” x 2-3/4” hex head bolt, lock washer, and nut provided in the retainer areas.

Note: The operator controls are on the front of the deck and the discharge chute is on the right side. (Left and right are determined from looking in the direction of travel.)

3.Install the two rear axle assemblies in the retainers on the rear of the mower deck. The tire should be to the left of the axle support. See figure 1. Secure with 3/8” x 2-1/2” hex head bolt, lock washer, and nut provided in the retainer areas.

1

Image 2

Contents OWNER’S MANUAL With Assembly Instructions For Models C60K, H60T, H60H & E60B60” FINISH CUT C60KYou should have ASSEMBLY INSTRUCTIONSA. ASSEMBLY OF MOWER WHEELS Optional hitchesFigure 2 Installation of Caster Support Stop Offset Tongue Position Direct Behind Tongue PositionRead all Owners Manuals before using equipment OPERATIONS AND ADJUSTMENTSD. INSTALLATION OF OPTIONAL HITCHES A. HITCH CONFIGURATIONS Refer to Figure B. ATV TONGUE CONFIGURATIONS Refer to Figure C. ADJUSTING CUTTING HEIGHT For Model H60H The engine full speed setting with mower blades running is 3350 RPMD. STARTING ENGINE Start engine and move throttle toward slow position to disengage choke For Model H60H Backing up with one wing mower is easy. Backing becomes a greater challenge as additional wing mowers are towed. Avoid backing up by planning ahead. Make loops instead of backing Model C60K - See Figure G. DRIVE BELT REMOVAL AND TENSIONModels H60T & H60H - See Figure For Model E60B - See Figure Always balance the mower blades each time they are sharpened H. MOWER BLADE REMOVAL, BALANCING & INSTALLATIONSharp blades can cause bodily injury if not handled properly K. TRANSPORTATION OF MOWER I. LUBRICATIONJ. TIRE PRESSURE L. STORAGEModel WING MOWER SPECIFICATIONSDIMENSIONS ENGINEE60B H60HC60K ACREASE WING MOWER PARTS MODEL C60KDescription MODEL C60KACREASE WING MOWER PARTS MODEL H60T H60TH60T ACREASE WING MOWER PARTS MODEL E60B E60BMODEL E60B ACREASE WING MOWER PARTS MODEL H60H QuantityMODEL H60H LAWN & GARDEN HITCH PARTS H60T, E60B & H60HDescription ATV TONGUE PARTSOPTIONAL HITCH PARTS SAFETY SIGNS AND LOCATIONS Clean or Replace Any Safety Signs That Are not Readable or DamagedOPTIONAL EQUIPMENT OPTIONAL FLOATATION KIT