Kunz C60K, H60T, H60B, E60B owner manual Installation of Caster Support Stop

Page 3
Figure 2: Installation of Caster Support Stop

Note: Tighten the four wheel assembly pivot bolts so that the wheel assemblies will not flop down when the deck is raised off the ground.

Caster Support

Caster Support Stop

Tongue

Figure 2: Installation of Caster Support Stop

B.INSTALLATION OF LAWN & GARDEN HITCHING (refer to the Operation and Adjustment Section for recommended hitching)(if the ATV Tongue was purchased refer to section C. Installation of ATV Tongue)

1.The tongue can be installed either on the left or right caster assembly depending on how the wing mower will be towed. See figure 1. Tighten the lock nut on the 3/8” x 2-1/2” pivot bolt so the tongue is free to pivot but does not move sideways.

Note: The tongue can be installed upside down so it will match up with tow vehicles with higher hitches.

2.The tow vehicle hitch provided is a universal hitch that should fit most tow vehicles. Slight modifications may be necessary for some tow vehicles.

3.Attach the tow vehicle hitch to the tow vehicle draw bar top or bottom depending on best support, and secure with the longer 1/2” hex head bolt, flatwasher, nut, and lockwasher provided. See figure 3.

Note: On some tow vehicles the draw bar will need to be strengthened to support the hitch assembly securely.

4.Adjust the hitch stop angle with stop bolts as close as possible to the vertical member on the back of the tow vehicle and adjust stop bolts securely against vertical member to keep hitch from pivoting from side to side.

Note: The hitch should be positioned on the tow vehicle so the stop bolts have a solid member to adjust to. On most tow vehicles two bolts can be used to attach the hitch assembly to the draw bar, eliminating the need for the hitch stop angle.

2

Page 2 Page 4
Image 3
Page 2 Page 4
Contents C60K With Assembly Instructions For Models C60K, H60T, H60H & E60B60” FINISH CUT OWNER’S MANUALOptional hitches ASSEMBLY INSTRUCTIONSA. ASSEMBLY OF MOWER WHEELS You should haveFigure 2 Installation of Caster Support Stop Direct Behind Tongue Position Offset Tongue PositionOPERATIONS AND ADJUSTMENTS D. INSTALLATION OF OPTIONAL HITCHESRead all Owners Manuals before using equipment A. HITCH CONFIGURATIONS Refer to Figure B. ATV TONGUE CONFIGURATIONS Refer to Figure C. ADJUSTING CUTTING HEIGHT The engine full speed setting with mower blades running is 3350 RPM D. STARTING ENGINEFor Model H60H Start engine and move throttle toward slow position to disengage choke For Model H60H Backing up with one wing mower is easy. Backing becomes a greater challenge as additional wing mowers are towed. Avoid backing up by planning ahead. Make loops instead of backing G. DRIVE BELT REMOVAL AND TENSION Models H60T & H60H - See FigureModel C60K - See Figure For Model E60B - See Figure H. MOWER BLADE REMOVAL, BALANCING & INSTALLATION Sharp blades can cause bodily injury if not handled properlyAlways balance the mower blades each time they are sharpened L. STORAGE I. LUBRICATIONJ. TIRE PRESSURE K. TRANSPORTATION OF MOWERENGINE WING MOWER SPECIFICATIONSDIMENSIONS ModelH60H E60BACREASE WING MOWER PARTS MODEL C60K DescriptionC60K C60K MODELH60T ACREASE WING MOWER PARTS MODEL H60TH60T E60B ACREASE WING MOWER PARTS MODEL E60BMODEL E60B Quantity ACREASE WING MOWER PARTS MODEL H60HMODEL H60H H60T, E60B & H60H LAWN & GARDEN HITCH PARTSATV TONGUE PARTS OPTIONAL HITCH PARTSDescription Clean or Replace Any Safety Signs That Are not Readable or Damaged SAFETY SIGNS AND LOCATIONSOPTIONAL FLOATATION KIT OPTIONAL EQUIPMENT
Top Page Image Contents