Kunz C60K, H60T, H60B, E60B owner manual D. Starting Engine, For Model H60H

Page 9
D.STARTING ENGINE

4.Adjust the cutting height on the wing mower so that it cuts at the same height as the tow vehicle mower. Adjust each corner of the wing mower so that the distance form the smooth surface to the bottom edge of the deck is equal to the cutting height minus 5/16”. The mower blade cutting edge is 5/16” above the lower edge of the deck.

Note: To mow in the lower half of the cutting range, set the front caster axles in the bottom setting and set the anti-scalp wheels in the top hole. To mow in the upper half of the cutting range (original factory setting), set the front caster axles in the top setting and set the anti-scalp wheels in the bottom hole.

Note: After the cutting height has been set, be sure to tighten the pivot bolts securely to eliminate free pivoting of the front casters or rear axles. Snug the four bolts just beyond the height adjust bolt so the front casters and rear axles can be adjusted up and down but cannot move from side to side.

D.STARTING ENGINE

The engine full speed setting with mower blades running is 3350 RPM. Set parking brake on tow vehicle. Attach wing mower tongue to tow vehicle.

For Model H60H: Do not start wing mower unless it is attached to the tow vehicle. For Models H60T & C60K:

Set the choke to the desired position.

Set the throttle lever in the start position at about half throttle. The mower blades clutch will engage as the engine comes up to speed. The mower blades clutch engages at 1850 RPM.

Start engine and allow engine to warm up.

Adjust the choke to off.

Adjust engine speed to full throttle to fully engage the mower blades clutch.

Clutch overheating or failure may occur if engine is not run at full speed in heavy load conditions.

The engine full speed setting with mower blades running is 3350 RPM.

For Model H60H:

Set the throttle lever in the choke position to set the choke. (The choke is located beyond the full throttle detent position.)

8

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 60” FINISH CUT With Assembly Instructions For Models C60K, H60T, H60H & E60BOWNER’S MANUAL C60KA. ASSEMBLY OF MOWER WHEELS ASSEMBLY INSTRUCTIONSYou should have Optional hitchesFigure 2 Installation of Caster Support Stop Direct Behind Tongue Position Offset Tongue PositionOPERATIONS AND ADJUSTMENTS D. INSTALLATION OF OPTIONAL HITCHESRead all Owners Manuals before using equipment A. HITCH CONFIGURATIONS Refer to Figure B. ATV TONGUE CONFIGURATIONS Refer to Figure C. ADJUSTING CUTTING HEIGHT The engine full speed setting with mower blades running is 3350 RPM D. STARTING ENGINEFor Model H60H Start engine and move throttle toward slow position to disengage choke For Model H60H Backing up with one wing mower is easy. Backing becomes a greater challenge as additional wing mowers are towed. Avoid backing up by planning ahead. Make loops instead of backing G. DRIVE BELT REMOVAL AND TENSION Models H60T & H60H - See FigureModel C60K - See Figure For Model E60B - See Figure H. MOWER BLADE REMOVAL, BALANCING & INSTALLATION Sharp blades can cause bodily injury if not handled properlyAlways balance the mower blades each time they are sharpened J. TIRE PRESSURE I. LUBRICATIONK. TRANSPORTATION OF MOWER L. STORAGEDIMENSIONS WING MOWER SPECIFICATIONSModel ENGINEH60H E60BACREASE WING MOWER PARTS MODEL C60K DescriptionC60K C60K MODELH60T ACREASE WING MOWER PARTS MODEL H60TH60T E60B ACREASE WING MOWER PARTS MODEL E60BMODEL E60B Quantity ACREASE WING MOWER PARTS MODEL H60HMODEL H60H H60T, E60B & H60H LAWN & GARDEN HITCH PARTSATV TONGUE PARTS OPTIONAL HITCH PARTSDescription Clean or Replace Any Safety Signs That Are not Readable or Damaged SAFETY SIGNS AND LOCATIONSOPTIONAL FLOATATION KIT OPTIONAL EQUIPMENT
Top Page Image Contents