Kohler 116347-2 manual Iallai

Page 11

￿￿￿D ￿￿CKE￿ ￿￿E￿A￿A￿I￿￿

￿￿￿E: Carefully study the roughing7in pages located in the inside back cover pocket, and the illustration at right before you begin construction of the stud pocket. Follow the framing details carefully.

Use ￿x4 framing for the stud pocket. Make sure you allow for access to the pump in the event the BodySpa requires service. Determine the drain location.

We recommend a room size approximately 607inches long x 487inches wide x 847inches high for the Custom BodySpa installation. The basin design must

provide

for a

water depth of at least

37inches above

the top of the suction cover. This

will

allow

an

overall

basin depth of about 97inches. The threshold of the

basin should be 6 to 77inches above the top

of

the

suction

cover.

Construct the basin framing to

result

in

an

overall

basin water capacity

between 90

and

￿00

gallons.

 

 

 

 

 

I￿￿￿ALLA￿I￿￿

You must provide at least 3￿ cubic feet (length x width x height) of unrestricted air space around

the pump box for the motor to cool properly and to provide access to the pump. We suggest you construct a false wall behind the face wall framing.

Locate the false wall along

the

tower wall.

 

 

For new installations, build

this false wall so at

 

least

￿￿7inches of access space exists

to

the back

of

the face wall. For existing installations with

 

 

finished walls, or if separate

access

panels for

the

pump,

drain,

water

supplies,

and

suction

assembly

 

are not feasible, provide more than ￿47inches of

 

access space between the false and face

walls

so

a

repair

person

can

maneuver

between

the

walls.

 

 

Carefully study the door enclosure installation instructions packed with the door enclosure. Construct suitable framing for the door enclosure, including a header and support framing above the doorway to prevent heat and moisture from escaping. Remember to locate the door enclosure perpendicular to the tower wall.

If you plan to install grab bars or other accessories, provide sufficient backing.

Check ￿oint #1

-￿oom size and layout known.

-￿rovide 32 cu. ft. air space around pump box.

-Footbath basin size and shape known.

-Face and false wall locations known.

-Drain location known.

￿￿63477￿7AA (A)

￿￿

Kohler Co., Kohler, WI

Image 11
Contents EI IE Room Size Provide Sufficient AccessDesign Guide Tower and SystemPump BOX WATER%FREE ZoneSuction Assembly Wiring ConnectionsWaterproofin Material Esin UIERain Loation Keypad Control Location Cement BoardWATER*RESISTANT Wall Material Finished Wall MaterialFootbath Basin Project Requirement Summary Primary Heat SourceAuxiliary Heat Sources Faucets and FittingsCustom Bodyspa Installation Instructions InstallationEetri Requireets FeturesIallai Plumbing Preparation Install Tower Mounting FrameInstall Pump BOX Install the Variable Flow Valve Assembly Install the Suction Bracket Make Electrical Connections Solvent Weld TubingInstall Cable Without Outlet BOX Install Cable with Outlet BOXInstall Suction Bushing Install Waterproofing Membrane or CompoundConstruct Footbath Basin Install Cement BoardInstall WATER0RESISTANT Wall Material Strut Fiise SI, WS, EII IA E D ECE DAIInstall the Tower Install the Keypad Water Test the System CLEAN/UP After InstallationSymptoms Probable Causes Corrective Action TroubleshootingCustom Bodyspa Users Information Users InformationInformation UsersLets GET Started Care and Cleaning of Your Custom Bodyspa Service and Warranty Information Page Publication No AA2 a E 1999 Kohler Co., Kohler, WI