Honda Power Equipment HRB425C owner manual Maintenance and Storage

Page 9

GB

SAFETY INSTRUCTIONS

 

C6. Always be sure of your footing on slopes. Mow across the face of slopes, never up and down.

C7. Exercise extreme caution when changing direction on slopes.

C8. Do not mow slopes of more than 20°.

C9. Use extreme caution when pulling the lawn mower towards you.

C10. Stop the blade if the lawn mower has to be tilted for transportation when crossing surfaces other than grass, and when transporting the lawn mower to and from the area to be mowed.

C11. Never operate the lawn mower with defective guards or housings, or without safety devices such as deflectors and/or grass catchers.

C12. Do not change the engine governor settings or overspeed the engine.

C13. Disengage all blade (models equipped with Rotostop) and drive clutches (self-propelled models) before starting the engine.

C14. Start the engine carefully according to instructions and with feet well away from the blade.

C15. Do not tilt the lawn mower when starting the engine. Start the mower on a level surface, free of high grass or obstacle.

C16. Keep hands and feet away from the rotating parts. Do not start the engine when standing in front of the discharge opening.

C17. Never pick up or carry a lawn mower while the engine is running.

C18. Stop the engine and disconnect the spark plug cap in the following cases:

-Before any operation under the cutter housing or the discharge tunnel.

-Before checking, cleaning or working on the lawn mower.

-After striking a foreign object. Inspect the lawn mower for damage and make repairs before restarting and operating the lawn mower again.

-If lawn mower starts to vibrate abnormally. Check immediately the cause of the vibration and perform the necessary repair.

C19. Stop the engine in the following cases:

-Whenever you leave the lawn mower unattended.

-Before refuelling.

C20. Stop the blade (models equipped with Rotostop) or the engine in the following cases:

-When installing or removing the grass bag.

-Before adjusting the cutting height.

C21. Reduce the throttle setting during engine shut-down. Close the fuel shut-off valve by turning the fuel shut-off valve.

MAINTENANCE AND STORAGE

D1. Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. Regular maintenance is an essential aid to user’s safety and retaining a high level of performance.

D2. Never store the equipment with petrol in the tank inside a building when vapours may reach an open flame, spark or high temperature source.

D3. Allow the engine to cool before storing in any enclosure.

D4. To reduce the fire hazard, keep the mower, especially the engine and silencer, the petrol storage area as well, free of grass, leaves, or excessive grease. Do not leave containers of vegetable matters in or near a building.

D5. If the fuel tank has to be drained, this should be done outdoors, with a cold engine.

D6. Check the grass collecting system frequently for wear or deterioration.

D7. Do not use the machine with worn or damaged parts. Parts must be replaced, not repaired. Replace worn or damaged parts with Honda genuine parts. Blades must always bear the mark Honda and the reference number. Non equivalent quality parts may damage the machine and be prejudicial to your safety.

D8. Wear thick gloves when removing or installing the blade or when cleaning the cutter housing. When tightening or loosening the blade screws, use a wooden block to prevent the blade from rotating.

D9. Always make sure the correct balance of the blade when sharpening.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents HRB425C Vorbeitungen UND Kontrollen VOR Inbetriebnahme InhaltsverzeichnisContents Préparations ET Vérifications Avant Utilisation Table DES MatièresZUR Beachtung / GB Note / F Note Anleitung SicherheitshinweiseVorbereitung Bedienungselemente UND BaugruppenInstandhaltung UND Lagerung Training Safety InstructionsPreparation OperationMaintenance and Storage Formation Consignes DE SécuritéPréparation UtilisationMaintenance ET Stockage HRB425C EinführungIntroduction Bauteile Rundlegende ErklärungenDescription Générale General DescriptionEquipment Identification Identification DES ÉlémentsGrundlegende Erklärungen Beschreibung DER SicherheitshinweiseTypenschild DER Machine Description of the Symbols Used in this Manual Safety Label LocationsExplication DES Symboles Utilisés Dans LE Manuel Identification of the MachineKontrolle DES Kraftstoffstandes Vorbeitungen UND Kontrollen VOR InbetriebnahmePréparations ET Vérifications Avant Utilisation Preparations and Checks Before USEChecking Fuel Level Vérification DU Niveau D’ESSENCEKontrolle DES Luftfilters Alkoholhaltiges BenzinFuel Containing Alcohol Checking the AIR CleanerEssence Contenant DE L’ALCOOL Vérification DU Filtre À AIRKontrolle DES Messers Vérification DE L’ÉTAT DE LA Lame Checking Blade ConditionSchnitthöheneinstellung Réglage DE LA Hauteur DE Coupe Adjusting Cutting HeightMehrbereichsöl ÖlstandkontrolleVérification DU Niveau DE L’HUILE Moteur Checking Engine OIL LevelKontrolle DES Grassacks Vérification DU SAC DE Ramassage Checking the Grass BAGAnlassen UND Abschalten DES Motors Starten DES MotorsChoke Schnell Langsam Stopp Mise EN Marche ET Arrêt DU Moteur Starting and Stopping the EngineStarting the Engine Mise EN Marche DU MoteurZUR Beachtung Betrieb in HöhenlagenFonctionnement EN Haute Altitude Using the Mower AT High AltitudesÜberfetteter Motor Abstellen DES MotorsFlooded Engine Stopping the EngineArrêt DU Moteur Moteur NoyéMähvorgang Empfehlungen FÜR DEN BetriebOperating Hints and Tips Mowing ProcedureConseils D’UTILISATION Procédure DE TonteEmpfehlungen FÜR DEN Betrieb Operating Hints and Tips Empfehlungen FÜR DEN Betrieb Operating Hints and Tips Ausleeren DES Grasfangsacks Vidage DU SAC DE Ramassage Emptying the Grass BAGWartungshinweise Wartung DES LuftfiltersHonda-Trockenluftfilterlinsätze nicht in Benzin reinigen AIR Cleaner Maintenance MaintenanceEntretien Entretien DU Filtre À AIRMotorölwechsel Changement DE L’HUILE Moteur Changing the Engine OILZündkerzenwechsel Bougie D’ALLUMAGE Spark PlugWartung DES Funkenfänger Sonderzubehör Spark Arrester Maintenance optional part Nachstellen DES Gaszugs Réglage DU Câble DE Commande DES GAZ Throttle Control Cable AdjustmentVergasereinstellung Einstellung DES MESSER- KupplungsspielsNormale Leerlauf-Drehzahl 1700 ± 150 U/min Blade Clutch Lever Free Play Carburetor AdjustmentRéglage DU Carburateur JEU AU Levier D’EMBRAYAGE DE LameSXE QXE PXE PQX Überprüfung DER SchwungradbremseContrôle DU Frein DE Volant Moteur Flywheel Brake InspectionEinstellen DES Fahrkupplungsspiels Modelle mit Radantrieb Einstellung DES Spiels VOM Bedienhebel DES MesserstopsRéglage DU Câble DE Frein DE Lame Blade Brake Cable AdjustmentMesserausbau Auswechseln DES MessersMontage ET Démontage DE Lame Blade Fitting and RemovalBlade Removal Démontage DE LA LameNachschleifen DES Messers Ersatz DER MessersMessereinbau Remplacement DE LA Lame Blade ReplacementBlade Sharpening Blade FittingGrasfangsack Pflege UND Erneuerung Anzugsmoment der Messerschrauben 5.5 kmg = 55 N.mSäubern DES Sacks BAG Cleaning Grass BAG Cleaning and ReplacementNettoyage ET Changement DU SAC DE Ramassage Nettoyage DU SACErneuern DES Grasfangsacks Überprüfung DES AntriebriemensForward Drive Belt Check BAG ReplacementVérification DE LA Courroie D’AVANCEMENT Changement DU SACAntriebskette Einstellung DES RiemenantriebsFinal Transmission Chain Belt Tension AdjustmentRéglage DE LA Tension DE LA Courroie Chaîne DE TransmissionHäufigkeit WartungsplanBauteil Aktion Alle zwei JahreFrequency Maintenance ScheduleIntervention Every 2 yearsPériodicité Calendrier D’ENTRETIENÉlément Intervention Tous les 2 ansStörungsbeseitigung StörungMögliche Ursache Problem Probable cause TroubleshootingIncident Cause probable Dépistage DES PannesGerätetransport Transport DES RasenmähersEinladen DES Rasenmähers Transporting the Mower TransportLoading the Mower Transport DE LA TondeuseLängere AUßERBETRIEBSETZUNG Remisage StoragePreparations for Storing the Mower Préparation Pour LE RemisageWiederinbetriebnahme Nach DER Einlagerung Réutilisation Après Remisage Using the Mower After a Storage PeriodModell HRB425C Technische DatenModel HRB425C Technical SpecificationsModèle HRB425C Spécifications Techniques

HRB425C specifications

The Honda Power Equipment HRB425C is a robust and efficient lawn mower designed for homeowners and professional landscapers alike. Known for its reliability and innovative features, the HRB425C is engineered to provide exceptional performance in a variety of mowing conditions.

One of the standout features of the HRB425C is its powerful Honda GCV160 engine. This 4-stroke, air-cooled engine ensures reliable starting and efficient fuel consumption. With a maximum output of 5.5 horsepower, this mower delivers ample power to tackle even the toughest grass. Its advanced ignition system provides quick starts and smooth operation, reducing the hassle often associated with traditional mowers.

The HRB425C boasts a cutting width of 21 inches, making it suitable for both small and medium-sized lawns. The mower features a 3-in-1 cutting system, allowing users to choose between bagging, mulching, or side discharge. The mulching capability is particularly noteworthy, as it finely chops grass clippings and returns them to the soil, providing natural fertilizer and improving lawn health.

Operator comfort is a priority in the design of the HRB425C. The mower is equipped with an adjustable handlebar, which can be set to different heights to accommodate users of various sizes. The ergonomic design minimizes fatigue during extended mowing sessions, making it a favorite among professionals.

In terms of build quality, the HRB425C features a durable, steel deck that is designed to withstand wear and tear. Its robust construction ensures longevity, allowing users to get years of reliable service from this mower. Additionally, the mower's wheels are equipped with durable treads that maximize traction on uneven terrain, providing stability and control while mowing.

Another significant feature of the HRB425C is its quick-adjust cutting height. With a simple lever adjustment, users can select from multiple cutting heights, ranging from 3/4 inch to 4 inches, allowing for versatility in grass length and health.

Honda's commitment to innovation is evident in the HRB425C's low emissions technology. The engine meets stringent environmental standards, making it an eco-friendly choice for consumers. Moreover, the mower operates quietly, making it suitable for residential areas where noise reduction is a priority.

Overall, the Honda Power Equipment HRB425C combines power, efficiency, and user-friendly features, making it a top choice for maintaining excellent lawn care. Its blend of dependability and advanced technology ensures that it stands out in the crowded market of lawn mowers, providing a superior mowing experience for all users.
Top Page Image Contents