Honda Power Equipment FL6555 manual Start-Up Procedure, Manual

Page 24

I SET-UP INSTRUCTIONS .

Start-Up Procedure

Ensure tractor meets all requirements as outlined in tractor preparation section of this

manual.

Check to ensure all labels are installed. Refer to safety label page for label locations.

Check tractor hydraulic fluid level. Refer to

tractor operator’s manual for fluid specifications.

Bucket and Lift Cylinders should be fully retracted when checking fluid level.

Check all hydraulic connections to ensure that they are adequately tightened.

Lubricate all pivot points that incorporate grease fittings.

Start tractor and run engine at approximately 1,200 - 1,400 R.P.M. for initial cycling of loader.

Operate all hydraulic cylinders to purge air from loader hydraulic system.

Recheck hydraulic oil level with all hydraulic cylinders fully retracted. Add recommended oil as required to return hydraulic oil to proper level as instructed in tractor owner’s manual.

Install loader bucket and bucket level indicator in the second hole from the top.

NOTE: Longest bucket pin is used to attach bucket level indicator.

Cycle Lift and Bucket Cylinders with bucket empty several times to seat-in cylinder components.

Inspect all hydraulic connections for evidence of leaks.

Check hydraulic hose routings to ensure adequate clearances exist between hoses and adjacent components.

19

wBefore using loader for the

-first time, cycle lift and bucket cylinders to purge air from cylinders and hydraulic system. Air In hydraulic system can cause unexpected fall of loader boom, causing Injury or damage to loader or tractor.

The tractor/loader should only be operated with all safety equipment properly installed.

Operate the loader from the tractor seat only.

1 -

mDo not stand or walk under

a ralsed attachment. Accldental movement of control lever or leak In hydraulic system could cause loader boom to drop, causing serious Injury. -

Make sure parked loader is on a hard level surface with all safety devices engaged to prevent loader from falling and being damaged or injuring someone.

A -

mBefore disconnecting hydraulic llnes, relieve all hydraulic pressure by operating hydraulic control lever through all positions with engine off. Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious personal Injury. Oil must be surgically removed within a few hours by a doctor familiar with this type of injury or gangrene may result.

LONGEST BUCKET PIN

n

22

Page 23 Page 25
Image 24
Page 23 Page 25
Contents OPERATOR’S Manual \# DPage Page Safety Loader Removal and InstallationLubrication and Maintenance Service Replacement Parts IntroductionSerial Number and Location Safety Front Loader SafetySafe Operating Rules Before Starting OperationSafety Maintenance Safety Safety Label Locations InformationShipping Inventory Hydraulic Hose Assembly LABEL, Hydraulic Functions Bucket Level Indicator Tube AssyBolt Sack Do not Exceed the Rating for Maximum Gross Vehicle Weight Tractor PreparationFL6555 Front Loader and BH6575 Backhoe Tire TypesLoader Specifications SET-UP Instructions GeneralProper Torque for Fasteners Bolt Head MarkingsSUB Frame Installation Removal WITH-OUT Mower InstallationWith Mower Installation Cl0 SUB Frame Installation and Removal SUB Frame Installation and Removal ‘DRAULIC Valve Package Connected to the loader hydraulic valve aJT port Tubes will be easier if youTubes to the loader arm Loader Assembly Installation Start-Up Procedure ManualSET-UP Instructions SET-UP Instructions Operation Cold Weather OperationScraping BackfillinglBackgradingLoading Safety Transporting MaterialUnloading Yy-lf# Page Loader Removal Installation Start the tractor and shift the loader control End of Season Beginning of SeaSOnLoader Installation Lubrication Maintenance MovementAccidental Tractor/loader shouldService Interval Lift and Bucket Cylinder RodService Cylinder Disassembly Lift and Bucket CylinderGeneral Cylinder Assembly InspectionTest Procedure Lift and Bucket Cylinder Leakage TestBucket Cylinder Test Disconnect from Piston Seal Assembly Leakage Test BodyHydraulic Valve Load Check Valve Service Relief ValveValve Spools Lift Cylinder Spool FloatAssembly InstallationHydraulic Valve Installation Relief Valve Test/AdjustmentPressure Trouble Shooting Problem Possible CauseCorrection Problem Possible Cause Problem Problem Problem Hydraulic System Schematic Quick Disconnect CouplerParts List Single Lever ControlDescription REQ’D HandleREF. Description REQ’D Detent Spring Spool Steelball OrificeValve Hydraulics Hydraulic HoseREF. . . . . . . . Description Bucket Cylinder REF Description . . . . . REQ’D Boom Cylinder REF Description . . . . . REQ’D Bucket Level Indicator Indicator AlTACHMENT bucket levelParking LEG Soaderboom Assembly IEF Clamp NUTCarriage Bolt Locwasher NUT PIN Clip Description Description REQ’D Warranty Service Page

FL6555 specifications

The Honda Power Equipment FL6555 is a versatile and powerful addition to Honda's line of outdoor tools, designed to meet the needs of both professional landscapers and homeowners alike. This model excels in performance, reliability, and efficiency, making it a top choice for those looking for high-quality lawn care equipment.

One standout feature of the FL6555 is its robust engine. Powered by Honda's commercial-grade engine, the FL6555 offers impressive torque and power, ensuring efficient operation even under demanding conditions. This engine is engineered for durability and longevity, making it a dependable choice for heavy-duty tasks.

The FL6555 is equipped with a 21-inch cutting deck, which provides a wide cutting path, allowing users to complete their mowing tasks more quickly and efficiently. The cutting height can be easily adjusted, offering several options to accommodate different grass types and mowing conditions. This flexibility ensures users can achieve the perfect lawn while minimizing the time spent on maintenance.

Another notable characteristic of the Honda FL6555 is its advanced transmission system. The hydrostatic transmission offers smooth and precise control, allowing users to easily maneuver the mower over various terrains. This feature not only enhances comfort during operation but also enables a more accurate cut, further improving the overall quality of the lawn.

The FL6555 also incorporates Honda's innovative technologies aimed at enhancing ease of use. The mower features an ergonomic design with cushioned handles, making it comfortable to operate for extended periods. Additionally, the mower's lightweight construction ensures ease of transport, enabling users to move it effortlessly from one location to another.

Safety is a top priority for Honda, and the FL6555 is equipped with several safety features, including an operator presence control, which stops the engine when the user releases the handle. This design minimizes the risk of accidents, allowing for safer operation in a variety of environments.

In summary, the Honda Power Equipment FL6555 combines power, efficiency, and user-friendly features. Its robust engine, versatile cutting deck, advanced transmission, and safety mechanisms make it an ideal choice for anyone looking to maintain a beautiful lawn with ease and reliability. Whether for professional landscaping or residential upkeep, the FL6555 stands out as a reliable and effective tool in the Honda lineup.
Top Page Image Contents