Honda Power Equipment FL6555 manual Cold Weather Operation

Page 27

OPERATION

Precautionary Notes

Do not lower the edge of the bucket too low for loading. Keep the bottom of the bucket level with the ground when loading.

1-j Do not use bucket for pushing down material with bucket cylinders partially extended. Damage to the cylinders may result.

Do not tip bucket cutting edge down (fully

extend bucket cylinders) during bacMilling/backgrading operation.

Operation with front tractor wheels off the ground is not recommended.

Position vehicles to be loaded as near the pile as possible and in such a direction as to minimize the amount of tractor turning required to dump.

Do not lowerthe loaderwith the tractor engine shut off.

Keep the unit clean and perform regular service. Observe safety instructions whenever cleaning, servicing, or lubricating.

We urge you to follow this advice:

Read and understandthis manual as well

as the Tractor Owner’s Manual.

Remember and observe the Safety Precautions brought to your attention in this manual, the tractor manual and on the machinery itself.

Use good common sense in the everyday

operation of this unit. Safety

recommendations can never be all-inclusive. You are responsible for watching out for, and avoiding, unsafe conditions.

Never exceed the limits of a piece of

.machinery. If its ability to do a job safely is in question - Don’t try it.

OPERATION

Don’t hurry the learning process or take the unit for granted. Ease into it and become familiar with your’new loader and tractor.

When lowering a heavy load, ease it downward slowly. Never drop a loaded attachment and ‘catch” hydraulically.

Stopping a load after it has gained downward momentum places undue strain on the unit and may cause unnecessary damage to the loader or tractor or even worse, personal injury.

1-

mEscaping hydraulic oil under Dressure can have sufficient force to aenetrate the skin causing serious Dersonal injury. If injured by escaping lydraulic oil, consult a physician mmediately. Oil must be surgically Pemovedwithin a few hours by a doctor iamiliar with this type of injury or gangrene nay result. Before disconnecting hydraulic lines, relieve .all hydraulic pressure by operating hydraulic control leverthrough all positions with engine off.

L -

-Asudden line burst can cause the mainframe to drop suddenly, causing damage to the tractor or loader or injury to personnel. Do not operate the loader if the fittings are leaking or if the hoses are damaged.

BEFORE OPERATING, LUBRICATE ALL

MOVING PARTS (REFER TO LUBRICATION SECTION).

Cold Weather Operation

To assure smooth operation in cold weather, allow tractor to warm up. SLOWLY cycle the loader and attachment several times to warm

the fluid in the hydraulic system. The loader

may operate erratically until the hydraulic fluid has warmed to operating temperatures.

25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents \# D OPERATOR’S ManualPage Page Safety Loader Removal and InstallationLubrication and Maintenance Service Replacement Parts IntroductionSerial Number and Location Safety Front Loader SafetySafe Operating Rules Operation Before StartingSafety Maintenance Safety Information Safety Label LocationsShipping Inventory Hydraulic Hose Assembly LABEL, Hydraulic Functions Bucket Level Indicator Tube AssyBolt Sack Tire Types Do not Exceed the Rating for Maximum Gross Vehicle WeightTractor Preparation FL6555 Front Loader and BH6575 BackhoeLoader Specifications General SET-UP InstructionsBolt Head Markings Proper Torque for FastenersSUB Frame Installation Removal WITH-OUT Mower InstallationWith Mower Installation Cl0 SUB Frame Installation and Removal SUB Frame Installation and Removal ‘DRAULIC Valve Package Connected to the loader hydraulic valve aJT port Tubes will be easier if youTubes to the loader arm Loader Assembly Installation Manual Start-Up ProcedureSET-UP Instructions SET-UP Instructions Cold Weather Operation OperationBackfillinglBackgrading ScrapingLoading Safety Transporting MaterialUnloading Yy-lf# Page Loader Removal Installation Start the tractor and shift the loader control Beginning of SeaSOn End of SeasonLoader Installation Tractor/loader should Lubrication MaintenanceMovement AccidentalLift and Bucket Cylinder Rod Service IntervalService Cylinder Disassembly Lift and Bucket CylinderGeneral Inspection Cylinder AssemblyTest Procedure Lift and Bucket Cylinder Leakage TestBucket Cylinder Test Disconnect from Body Piston Seal Assembly Leakage TestHydraulic Valve Lift Cylinder Spool Float Load Check Valve ServiceRelief Valve Valve SpoolsInstallation AssemblyHydraulic Valve Installation Relief Valve Test/AdjustmentPressure Trouble Shooting Problem Possible CauseCorrection Problem Possible Cause Problem Problem Problem Quick Disconnect Coupler Hydraulic System SchematicHandle Parts ListSingle Lever Control Description REQ’DSpool Steelball Orifice REF. Description REQ’D Detent SpringHydraulic Hose Valve HydraulicsREF. . . . . . . . Description Bucket Cylinder REF Description . . . . . REQ’D Boom Cylinder REF Description . . . . . REQ’D Bucket Level Indicator Indicator AlTACHMENT bucket levelParking LEG Soaderboom Assembly IEF Clamp NUTCarriage Bolt Locwasher NUT PIN Clip Description Description REQ’D Warranty Service Page

FL6555 specifications

The Honda Power Equipment FL6555 is a versatile and powerful addition to Honda's line of outdoor tools, designed to meet the needs of both professional landscapers and homeowners alike. This model excels in performance, reliability, and efficiency, making it a top choice for those looking for high-quality lawn care equipment.

One standout feature of the FL6555 is its robust engine. Powered by Honda's commercial-grade engine, the FL6555 offers impressive torque and power, ensuring efficient operation even under demanding conditions. This engine is engineered for durability and longevity, making it a dependable choice for heavy-duty tasks.

The FL6555 is equipped with a 21-inch cutting deck, which provides a wide cutting path, allowing users to complete their mowing tasks more quickly and efficiently. The cutting height can be easily adjusted, offering several options to accommodate different grass types and mowing conditions. This flexibility ensures users can achieve the perfect lawn while minimizing the time spent on maintenance.

Another notable characteristic of the Honda FL6555 is its advanced transmission system. The hydrostatic transmission offers smooth and precise control, allowing users to easily maneuver the mower over various terrains. This feature not only enhances comfort during operation but also enables a more accurate cut, further improving the overall quality of the lawn.

The FL6555 also incorporates Honda's innovative technologies aimed at enhancing ease of use. The mower features an ergonomic design with cushioned handles, making it comfortable to operate for extended periods. Additionally, the mower's lightweight construction ensures ease of transport, enabling users to move it effortlessly from one location to another.

Safety is a top priority for Honda, and the FL6555 is equipped with several safety features, including an operator presence control, which stops the engine when the user releases the handle. This design minimizes the risk of accidents, allowing for safer operation in a variety of environments.

In summary, the Honda Power Equipment FL6555 combines power, efficiency, and user-friendly features. Its robust engine, versatile cutting deck, advanced transmission, and safety mechanisms make it an ideal choice for anyone looking to maintain a beautiful lawn with ease and reliability. Whether for professional landscaping or residential upkeep, the FL6555 stands out as a reliable and effective tool in the Honda lineup.
Top Page Image Contents