Honda Power Equipment FL6555 manual Inspection, Cylinder Assembly

Page 40

SERVICE,

Ensure hands and face are kept clear of end of cylinder.

With rod packing set out of cylinder body,

remove the retaining wire located approximately l-1/4” in from end of cylinder body by pressing on one side to force the retaining wire 90 out of the groove and pull retaining wire out of cylinder body.

Pull cylinder rod out of cylinder body.

Secure the cylinder rod in a bench vise by the end eye of the rod. Do not clamp on the chromed finish section of the rod.

Remove piston assembly lock nut and pull piston assembly from rod.

Remove piston seal and backups from piston.

Clean all parts for inspection.

inspection

inspectcylinder body for evidence.of scoring and pitting. Replace cylinder body if excessive pitting/scoring is evident.

Inspect cylinder rod for evidence of pitting or plating deterioration through the section of the rod that contacts the rod packing set.

Inspect cylinder rod and body end eyes and bushings for wear. The steel bushings should fit snugly in the end eyes.

Inspect end eye grease fittings and replace if damaged

Inspect cylinder packing guides and piston. Replace any components that exhibit excessive wear or damage.

Cylinder Assembly

Clean and dry all cylinder components thoroughly.

Place cylinder end cap on cylinder rod followed by rod packing set and retaining wire.

Refer to illustration for reference to component orientation and sequence.

Assemble piston seal and backups or piston and install piston assembly on cylinder rod. refer to illustration for reference to component orientation.

Install Locknut and torque to 225 ft./lbs.

Coat piston assembly with clean hydraulic oil and with the cylinder body supported in a bench vise, carefully install cylinder rod in cylinder body. Care must be taken to ensure piston seal is not damaged during installation.

Install the retaining wire in the cylinder body.

Coat rod packing set components with clean hydraulic oil and position in cylinder body.

Install cylinder end cap and tighten until rod packing set components are snug. Do not over-tighten as rod packing service life will be reduced.

Rod packing sets should be reset by tightening cylinder end cap l/4 turn after the initial 10 hours of cylinder operation.

Install dust plugs in cylinder ports.

38

Page 39 Page 41
Image 40
Page 39 Page 41
Contents OPERATOR’S Manual \# DPage Page Loader Removal and Installation SafetyLubrication and Maintenance Service Introduction Replacement PartsSerial Number and Location Front Loader Safety SafetySafe Operating Rules Before Starting OperationSafety Maintenance Safety Safety Label Locations InformationShipping Inventory Bucket Level Indicator Tube Assy Hydraulic Hose Assembly LABEL, Hydraulic FunctionsBolt Sack Do not Exceed the Rating for Maximum Gross Vehicle Weight Tractor PreparationFL6555 Front Loader and BH6575 Backhoe Tire TypesLoader Specifications SET-UP Instructions GeneralProper Torque for Fasteners Bolt Head MarkingsWITH-OUT Mower Installation SUB Frame Installation RemovalWith Mower Installation Cl0 SUB Frame Installation and Removal SUB Frame Installation and Removal ‘DRAULIC Valve Package Tubes will be easier if you Connected to the loader hydraulic valve aJT portTubes to the loader arm Loader Assembly Installation Start-Up Procedure ManualSET-UP Instructions SET-UP Instructions Operation Cold Weather OperationScraping BackfillinglBackgradingLoading Transporting Material SafetyUnloading Yy-lf# Page Loader Removal Installation Start the tractor and shift the loader control End of Season Beginning of SeaSOnLoader Installation Lubrication Maintenance MovementAccidental Tractor/loader shouldService Interval Lift and Bucket Cylinder RodCylinder Disassembly Lift and Bucket Cylinder ServiceGeneral Cylinder Assembly InspectionLift and Bucket Cylinder Leakage Test Test ProcedureBucket Cylinder Test Disconnect from Piston Seal Assembly Leakage Test BodyHydraulic Valve Load Check Valve Service Relief ValveValve Spools Lift Cylinder Spool FloatAssembly InstallationRelief Valve Test/Adjustment Hydraulic Valve InstallationPressure Problem Possible Cause Trouble ShootingCorrection Problem Possible Cause Problem Problem Problem Hydraulic System Schematic Quick Disconnect CouplerParts List Single Lever ControlDescription REQ’D HandleREF. Description REQ’D Detent Spring Spool Steelball OrificeValve Hydraulics Hydraulic HoseREF. . . . . . . . Description Bucket Cylinder REF Description . . . . . REQ’D Boom Cylinder REF Description . . . . . REQ’D Indicator AlTACHMENT bucket level Bucket Level IndicatorParking LEG Clamp NUT Soaderboom Assembly IEFCarriage Bolt Locwasher NUT PIN Clip Description Description REQ’D Warranty Service Page

FL6555 specifications

The Honda Power Equipment FL6555 is a versatile and powerful addition to Honda's line of outdoor tools, designed to meet the needs of both professional landscapers and homeowners alike. This model excels in performance, reliability, and efficiency, making it a top choice for those looking for high-quality lawn care equipment.

One standout feature of the FL6555 is its robust engine. Powered by Honda's commercial-grade engine, the FL6555 offers impressive torque and power, ensuring efficient operation even under demanding conditions. This engine is engineered for durability and longevity, making it a dependable choice for heavy-duty tasks.

The FL6555 is equipped with a 21-inch cutting deck, which provides a wide cutting path, allowing users to complete their mowing tasks more quickly and efficiently. The cutting height can be easily adjusted, offering several options to accommodate different grass types and mowing conditions. This flexibility ensures users can achieve the perfect lawn while minimizing the time spent on maintenance.

Another notable characteristic of the Honda FL6555 is its advanced transmission system. The hydrostatic transmission offers smooth and precise control, allowing users to easily maneuver the mower over various terrains. This feature not only enhances comfort during operation but also enables a more accurate cut, further improving the overall quality of the lawn.

The FL6555 also incorporates Honda's innovative technologies aimed at enhancing ease of use. The mower features an ergonomic design with cushioned handles, making it comfortable to operate for extended periods. Additionally, the mower's lightweight construction ensures ease of transport, enabling users to move it effortlessly from one location to another.

Safety is a top priority for Honda, and the FL6555 is equipped with several safety features, including an operator presence control, which stops the engine when the user releases the handle. This design minimizes the risk of accidents, allowing for safer operation in a variety of environments.

In summary, the Honda Power Equipment FL6555 combines power, efficiency, and user-friendly features. Its robust engine, versatile cutting deck, advanced transmission, and safety mechanisms make it an ideal choice for anyone looking to maintain a beautiful lawn with ease and reliability. Whether for professional landscaping or residential upkeep, the FL6555 stands out as a reliable and effective tool in the Honda lineup.
Top Page Image Contents