Dimension One Spas Dynamic Massage Sequencer Scrolling Message Center Digital Display Messages

Page 17

 

 

 

2002 Dimension One Spas Export Owner’s Manual

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Control

 

 

Function

 

 

 

 

5

 

 

5. ENTER Pad

 

 

 

 

 

 

This pad is used to exit any programming sequence at any time.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

6. PROGRAM Pad

 

 

 

 

 

 

 

This pad is used to initiate the time setting, filter programming, and other

 

 

 

 

 

 

 

programming features. For more information, see the next section,

 

 

 

 

 

 

 

“Programming the Scrolling Message Center.”

 

 

 

 

 

 

 

 

 

 

 

 

7

 

 

7. Dimension One Spas ICON (Logo)

 

 

 

 

 

 

The time of day can be viewed by pushing the Dimension One Spas ICON logo

 

 

 

 

 

 

 

 

 

 

 

 

 

 

on the far right of the control panel. If no other pad is pushed within 5 seconds,

 

 

 

 

 

 

 

the display will revert to the hot tub water temperature reading. The pre-set

 

 

 

 

 

 

 

factory default is Fahrenheit.

 

 

 

 

 

 

 

Pressing the logo for 5 seconds will place the spa in the “Standby” mode and

 

 

 

 

 

 

 

allow the spa to be cleaned without turning off the power.

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

8. Heat Status Light

 

 

 

 

 

 

This Light is illuminated whenever the heater is on.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Scrolling Message Center (Digital Display) Messages

Because of the advanced programming features of your scrolling display, your hot tub will prompt you when you need to perform routine maintenance. For example:

Rinse Filters

Every other month, the top line of your Digital Display will read, “RINSE FILTERS” and the message “REMOVE FILTERS & RINSE WITH HOSE... PUSH AND HOLD ICON PAD MORE THAN 3 SECONDS TO RESET THIS MESSAGE” will scroll from right to left on the bottom line of the display. To reset this message, push and hold the Dimension One Spas ICON (logo) located at the right hand side of the control for 3 seconds.

13

Image 17
Contents Page Page Table of Contents Surface Care Ultralife and Granitex To Reduce the Risk of Injury Important Safety InstructionsHazardous to your health HyperthermiaDo’s and Don’ts Vista, CA 92083 760 Jet System Selector Valve Hot Tub FeaturesFollowing features are included on your hot tub NeckFlex Jet Pillow Smart Heat Available only on Dimension One SpasUltra Pure Water Management System CrystalZone Water Management SystemTop Side Control OperationDigital Display Jets Low/High Control PadDimension One Spas Icon Logo Temperature PadsProgram Pad Heat Status LightDigital Display Messages Clock Set Using the Programmable Digital ControllerFilter Cycle Start Time Filter Cycle DurationInitial Startup Temperature Unit SelectionDigital Display LCD Temperature PadJets 1 and 2 Pads Light PadRinse Filters Scrolling Message Center Digital Display MessagesEnter Pad Change Water Clean FiltersChange Vision Cartridge Spa Check UpCooling IceSetting the Time Using the Scrolling Message CenterVision Cartridge Pump Run TimeDigital Display LCD Invert Control Panel LockControl Panel Description Control Panel ResetProgramming Unlock Sequence Indicator Lights 1 through Massage Zone Indicator Lights Human FigureJets Pad Speed PadMassage Zones Massage Zone DescriptionPanel Screws Operating the Dynamic Massage SequencerMale Hose Fitting Page Filter Cleaning Routine Equipment MaintenanceLight Bulb Replacement Draining Your EquipmentGranitex/Quarite Plus Dimension One EnviroTect Skirts and Vinyl CoversSurface Care Ultralife and Granitex Special Cold Weather Instructions Procedure for WinterizingCare for the Wood Spa Cabinet Items Required for WinterizingPage Spring Time Startup Replace all equipment access panels onto the systemGranitex  /Quarite Plus  Disclaimer Warranty Service InformationTerm Definition Glossary of TermsTemperature Electrical System Troubleshooting GuideHeating System Poor Water SystemPage