Dimension One Spas Dynamic Massage Sequencer Clean Filters, Change Water, Change Vision Cartridge

Page 18

2002 Dimension One Spas Export Owner’s Manual

Clean Filters

On alternating months, the top line of your Digital Display will read, “DIRTY FILTER” and the message “REMOVE FILTERS & CLEAN IN SOLUTION... PUSH AND HOLD ICON PAD MORE THAN 3 SECONDS TO RESET THIS MESSAGE” will scroll from right to left on the bottom line of the display. To reset this message, push and hold the Dimension One Spas ICON (logo) pad located at the right hand side of the control for 3 seconds.

Change Water

Every four months the top line of your Digital Display will read “CHANGE WATER” and the message “TURN

POWER OFF, DRAIN & REFILL SPA...PUSH AND HOLD ICON PAD MORE THAN 3 SECONDS TO RESET THIS MESSAGE” will scroll from right to left on the bottom line of the display. To reset this message, push and hold the Dimension One Spas ICON (logo) pad located at the right hand side of the control for 3 seconds.

Change Vision Cartridge

When “CHANGE VISION CARTRIDGE” is displayed on the LCD, the system is telling you that it is time to replace it. To reset this message, push and hold the Dimension One Spas ICON (logo) pad located at the right hand side of the control for 3 seconds.

If you purchased a Vision cartridge subsequent to the initial start up of your hot tub, please follow the programming instructions for VISION as outlined in the next section (titled, “Vision Cartridge”) to set the six-month time frame.

Note

Spa Check Up

When “SPA CHECK UP” is displayed on the Digital Display, we recommend that you have your hot tub inspected by your dealer as a preventative maintenance measure. To reset this message, push and hold the Dimension One Spas ICON (logo) pad located at the right hand side of the control for 3 seconds.

The system can dismiss and reset the maintenance messages by pushing and holding the Dimension One Spas ICON (logo), on the right end of the control, for 3 seconds. If you press the Dimension One Spas ICON (logo) for 5 seconds when there is no maintenance message, it will put the spa in the “Standby” mode.

Note

Overheat

When “OVERHEAT” is displayed on the control system Digital Display, the hot tub is in a high temperature condition. If such a condition exists, check water temperature and if it is above 104° F (40° C), DO NOT ENTER THE WATER. If this happens, remove the hot tub cover and allow the water to cool below 110° F (43.3° C). Reset the power to the spa by resetting the GFCI breaker. If the problem recurs, turn off all power to the hot tub and contact your local Authorized Dimension One Spas Dealer, or authorized service center.

Flashing Display and/or “Check Water Level”

If you see 3 flashing LEDs (on Digital Display) and/or the message, “CHECK WATER LEVEL -CLEAN FILTER-IF PROBLEM CONTINUES, TURN OFF POWER AND RESTART THE SYSTEM-IF PROBLEM CONTINUES, CALL FOR SERVICE” on the Digital Display, follow the instructions as stated. Check the water temperature and if it is above 104° F (40° C), DO NOT ENTER THE WATER.

Flashing Temperature on the Display

If you see a flashing temperature of 34° F (1.11° C) or 134° F (56.6° C), DO NOT ENTER THE WATER. The system has detected a problem. Call your dealer for service.

14

Image 18
Contents Page Page Table of Contents Surface Care Ultralife and Granitex Important Safety Instructions To Reduce the Risk of InjuryHyperthermia Hazardous to your healthDo’s and Don’ts Vista, CA 92083 760 Hot Tub Features Following features are included on your hot tubJet System Selector Valve Ultra Pure Water Management System Smart Heat Available only on Dimension One SpasNeckFlex Jet Pillow CrystalZone Water Management SystemDigital Display OperationTop Side Control Jets Low/High Control PadProgram Pad Temperature PadsDimension One Spas Icon Logo Heat Status LightDigital Display Messages Filter Cycle Start Time Using the Programmable Digital ControllerClock Set Filter Cycle DurationTemperature Unit Selection Initial StartupJets 1 and 2 Pads Temperature PadDigital Display LCD Light PadScrolling Message Center Digital Display Messages Enter PadRinse Filters Change Vision Cartridge Clean FiltersChange Water Spa Check UpIce CoolingUsing the Scrolling Message Center Setting the TimeDigital Display LCD Invert Pump Run TimeVision Cartridge Control Panel LockControl Panel Reset Programming UnlockControl Panel Description Jets Pad Massage Zone Indicator Lights Human FigureSequence Indicator Lights 1 through Speed PadMassage Zone Description Massage ZonesOperating the Dynamic Massage Sequencer Panel ScrewsMale Hose Fitting Page Light Bulb Replacement Routine Equipment MaintenanceFilter Cleaning Draining Your EquipmentDimension One EnviroTect Skirts and Vinyl Covers Surface Care Ultralife and GranitexGranitex/Quarite Plus Care for the Wood Spa Cabinet Procedure for WinterizingSpecial Cold Weather Instructions Items Required for WinterizingPage Replace all equipment access panels onto the system Spring Time StartupWarranty Service Information Granitex  /Quarite Plus  DisclaimerGlossary of Terms Term DefinitionTemperature Troubleshooting Guide Heating SystemElectrical System Water System PoorPage